BX BX AMPLIFIER BX360.4 BX500.
BX.4-SERIES AMPLIFIERS Owner’s Manual MODEL: BX360.4 / BX500.4 Authorized KICKER Dealer: Purchase Date: Model Number: Serial Number: PERFORMANCE Model: BX360.4 BX500.4 RMS Power, all channels driven @ 14.4V, 4Ω stereo, ≤ 1% THD+N @ 14.4V, 2Ω stereo, ≤ 1% THD+N @ 14.
INSTALLATION Mounting: Choose a structurally sound location to mount your KICKER amplifier. Avoid any damage of the vehicle’s components like wires, cables, board computer, seat belts, gastank where the screws be driven. Ensure that this chosen location provide sufficient air circulation for the amplifier. Do not mount the device into small or sealed spaces without air circulation near by heat dispersing parts or electrical parts of the vehicle.
FOUR CHANNEL OPERATION minimum impedance of 2 ohms per channel signal in signal in BRIDGED OPERATION (MONO) minimum impedance of 4 ohms signal in woofer 2 woofer 1 + AMP1 L – AMP2 R – AMP1 R + AMP2 L STEREO-AND-MONO-SIMULTANEOUSLY (SAMS) OPERATION minimum impedance of 4 ohms bridged (mono) and 2 ohms per channel stereo signal in signal in woofer – AMP2 R + AMP2 L 4 BX AMPLIFIERS
OPERATION Input Level: The RCA inputs on KICKER BX amplifiers are capable of receiving a Low-level signal from your source unit. If the only output available from your source unit is a Hi-Level signal, you can use the HI LEVEL INPUTS. Refer to the wiring section of this manual for additional instructions. Input Gain Control: The input gain control is not a volume control. It matches the output of the source unit to the input level of the amplifier.
BXRC* REMOTE BASS INSTALLATION * BXRC not included mount the housing phone cable TROUBLESHOOTING If your amplifier does not appear to be working, check the obvious things first such as blown fuses, poor or incorrect wiring connections, incorrect setting of crossover switch and gain controls, etc. There is a green POWER LED and a red PROTECTION LED on the end panel of your KICKER BX series amplifier.
Alternator noise-whining sound with engine’s RPM? Check for damaged RCA (or speaker input) cable Check the routing of RCA (or speaker input) cable Check the source unit for proper grounding Check the gain settings and turn them down if they are set too high. Poor stereo image or reduced bass response? Check system phasing by turning the balance control from left to right.
VERSTÄRKER BX.4 SERIE Benutzerhandbuch MODEL: BX360.4 / BX500.4 Autorisierter KICKER-Händler: Kaufdatum: Verstärker-Modellnummer: Verstärker-Seriennummer: TECHNISCHE DATEN Modell: BX360.4 BX500.4 RMS-Leistung, alle Kanäle betrieben @ 14.4V, 4Ω stereo, ≤ 1% Gesamtklirrfaktor @ 14.4V, 2Ω stereo, ≤ 1% Gesamtklirrfaktor @ 14.
h INSTALLATION Befestigung: Wählen Sie für die Installation des KICKER-Verstärkers einen geeigneten Einbauort. Vergewissern Sie sich, dass keine Kabel, Leitungen und andere Komponenten des Fahrzeugs beim Bohren beschädigt werden. Vergewissern Sie sich, dass der Verstärker am Montageort genügend Kühlung erhält. Montieren Sie das Gerät nicht in zu kleine, abgeschlossene Gehäuse ohne Luftzirkulation, in die Nähe von wärmeabstrahlende Teilen oder elektronischen Steuerungen des Fahrzeuges.
VIERKANALBETRIEB Mindestimpedanz von 2 Ohm pro Kanal Signaleingang Signaleingang BRÜCKENBETRIEB (MONO) Mindestimpedanz von 4 Ohm Signaleingang Tieftöner 2 Tieftöner 1 + AMP1 L – AMP2 R – AMP1 R + AMP2 L GLEICHZEITIGER STEREO- UND MONO-BETRIEB (SAMS) Mindestimpedanz von 4 Ohm (Mono) bzw.
BETRIEB Eingangspegel: Die RCA-Eingänge an KICKER BX-Verstärkern können nur Niedrigpegelsignale vom Autoradio empfangen. Wenn nur ein Hochpegelsignal vom Autoradio verfügbar ist, verwenden Sie den HI LEVEL INPUT (Hochpegeleingang) am Verstärker. Weitere Hinweise finden Sie im Abschnitt „Anschluss“ auf Seite 9. Xover-Schalter: Verwenden Sie den XOVER-Schalter, um die interne Frequenzweiche des jeweiligen Kanalpaars (AMP1 oder AMP2) auf OFF, LP oder HP einzustellen.
BXRC* BASSPEGEL-FERNBEDIENUNG INSTALLATION * BXRC ist nicht inbegriffen Gehäuse befestigen Telefonkabel PROBLEMBEHEBUNG Wenn der Verstärker nicht zu funktionieren scheint, sollten Sie zuerst offensichtliche Faktoren prüfen, wie durchgebrannte Sicherungen, schlechte oder fehlerhafte Verkabelung, inkorrekte Einstellung des XOVERSchalters und der Verstärkungsregler etc. Am Gerät befindet sich eine grüne LED (POWER) sowie eine rote PROTECT-LED.
Lichtmaschine erzeugt bei steigender Motordrehzahl heulendes Geräusch? Prüfen Sie, ob das RCA- oder Lautsprechereingangskabel defekt ist. Prüfen Sie den Verlauf des RCA- oder Lautsprechereingangskabels. Prüfen Sie, ob das Autoradio richtig geerdet ist. Prüfen Sie die Verstärkungseinstellungen und reduzieren Sie diese ggf. Prüfen Sie die RCA-Masse des Autoradios.
INTERNATIONAL WARRANTY Contact your International KICKER dealer or distributor concerning specific procedures for your country’s warranty policies. WARNING: KICKER products are capable of producing sound levels that can permanently damage your hearing! Turning up a system to a level that has audible distortion is more damaging to your ears than listening to an undistorted system at the same volume level.
BX AMPLIFIERS 15
Distribution: Audio Design GmbH Am Breilingsweg 3, D-76709 Kronau Tel. +49(0)7253-9465-0, Fax +49(0)7253-9465-10 www.audiodesign.