KXM AMPLIFIERS Owner’s Manual KXMA400.2 | KXMA1200.2 KXMA500.4 | KXMA800.
KXMA STEREO-SERIES AMPLIFIERS OWNER’S MANUAL MODEL: KXMA400.2 | KXMA1200.2 | KXMA500.4 | KXMA800.4 IMPORTANT SAFETY WARNING PROLONGED CONTINUOUS OPERATION OF AN AMPLIFIER, SPEAKER, OR SUBWOOFER IN A DISTORTED, CLIPPED OR OVER-POWERED MANNER CAN CAUSE YOUR AUDIO SYSTEM TO OVERHEAT, POSSIBLY CATCHING FIRE AND RESULTING IN SERIOUS DAMAGE TO YOUR COMPONENTS AND/OR VEHICLE. AMPLIFIERS REQUIRE UP TO 4 INCHES (10CM) OPEN VENTILATION. SUBWOOFERS SHOULD BE MOUNTED WITH AT LEAST 1 INCH (2.
source unit high-level speaker outputs KICKER KISL (optional) to amplifier core conductor OR + to amplifier – shield from source unit highlevel speaker outputs Install a fuse within 7” (18cm) of the battery and in-line with the power cable connected to your amplifier. Model External Fuse Power/Ground Wire KICKER Wiring Kit (sold separately) KXMA400.2 1 x 60 Ampere 8 Gauge KMPK8, PK8, CK8 KXMA1200.2 1 x 150 Ampere 1/0 Gauge PKD1 KXMA500.4 1 x 60 Ampere 4 Gauge KMPK4, PK4, CK4 KXMA800.
For multiple amplifier installations where distribution blocks are used, each amplifier should have its proper-rated fuse, or breaker, installed between the amplifier and the distribution block within seven inches of the block, or on the distribution block if it provides for fusing.
FOUR CHANNEL OPERATION minimum impedance of 2 ohm INPUT LEVEL L R LO/HI R L BRIDGED OPERATION (MONO) minimum impedance of 4 ohms INPUT LEVEL LO/HI Bridged operation unavailable with KXMA1200.
OPERATION Mini-USB for internal use only; do NOT remove or tamper. KICKER is not responsible for any damage to equipment resulting from connections made to this port. OFF/HP/LP/BP PRT KXMA400.2 0 11 GAIN GAIN MATCH 1X/10X 10 Hz 500 40 Hz 500 HI-PASS LO-PASS X-OVER LO-PASS RANGE 0 dB 6 KICK EQ Automatic Turn-On Selection: The KXMA series offers three different automatic turn-on modes that can be selected on the end panel; +12V, DC Offset, and Audio.
Set the 1X/10X frequency multiplier switch to the setting that is appropriate for your application. A setting of 10X will set the range of the AMP 1 crossover to 100–5,000Hz, and the low pass crossover of AMP 2 to 100–5,000Hz. For KXMA stereo amplifiers, the frequency multiplier switch will only affect the low pass crossover. KICK EQ Bass Boost Control: The variable bass boost control on the side of the amplifier is designed to give you increased output, 0–6dB, at 40Hz.
TROUBLESHOOTING If your amplifier does not appear to be working, check the obvious things first such as blown fuses, poor or incorrect wiring connections, incorrect setting of crossover switch and gain controls, etc. There is a Protection (PRT) LED on the side panel of your Kicker KXMA series amplifier. Depending on the state of the amplifier and the vehicle’s charging system, the LED will either glow red or be off. Red (PRT) LED flickering with loud music? The red (PRT) LED indicates low battery voltage.
ELECTRONICS LIMITED WARRANTY When purchased from an Authorized KICKER Dealer, KICKER warrants this product to be free from defects in material and workmanship under normal use for a period of TWO (2) YEARS from date of original purchase with receipt. If this product is identified as “Refurbished” or “B Goods”, the warranty is limited to a period of THREE (3) MONTHS from the date of original purchase. In all cases you must have the original receipt.
INTERNATIONAL WARRANTY Contact your International KICKER dealer or distributor concerning specific procedures for your country’s warranty policies. WARNING: KICKER products are capable of producing sound levels that can permanently damage your hearing! Turning up a system to a level that has audible distortion is more damaging to your ears than listening to an undistorted system at the same volume level.
©2020 Stillwater Designs
KXMA STEREO AMPLIFIER | AMPLIFICADOR DEL KXMA VERSTÄRKER DER KXMA | AMPLIFICATEUR DE KXMA KXMA400.2 | KXMA1200.2 | KXMA500.4 | KXMA800.
Wiring | Cabelado | Câblage | Verkabelung (KXMA400.2 shown) (Se muestra KXMA400.2) (KXMA400.2 illustré) (KXMA400.2 gezeigt) See owner’s manual for information on how to use amplifier features such as gain, crossover, bass boost and more! Consulte el manual del propietario para obtener información sobre cómo utilizar las funciones del amplificador, como ganancia, crossover, refuerzo de graves y más.
I POWER CHART I CUADRO DE POTENCIA LEISTUNGSDIAGRANINI I TABLEAU DE PUISSANCE {fKICKER V=SQRT(WATT*IMPEDANCE) RATED AMPLIFIER POWER IN WATTS 45W sow IMPEDANCE 40 20 10 o.so 65W 75W 100W 150W 200W 300W 24.49V 17 .32V 12.25V 8.66V 28.28V 20 .00V 14.14V 10.00V 34 .64V 24 .49V 17.32V 12.25V 900W 1000W 1200W 60.00V 42.43V 30.00V 21.21V 63.25V 44.72V 31.62V 22.36V 69 .28V 48 .99V 34.64V 24.49V 3000W 4000W 109.54V 77.46V 54 .77V 38 .73V 126.49V 89.44V 63.25V 44 .
