rouno rl:agc:rTM by{fKICKER Designed for the Jeep Wrangler, with applicable model years.
CONTENTS CON'T BRACKET ASSEMBLY 5-CHANNEL AMP POWER HARNESS M6 BOLT 15A FUSE 25A FUSE AMP SCREWS x4 AMP WASHERS x4 WIRE TIES x6 OVERLAY HARNESS Radio Removal 1. Disconnect the negative battery terminal. 2. Using a panel removal tool, pry up on the plastic trim panel located above the radio. Make sure to pry on the side of the panel closest to the window. Fig. 1 3. Using a panel removal tool pry loose the top edge of the panel below the HVAC controls . Fig.
4. Remove the four screws securing the radio trim bezel. There are two at the top and two at the bottom. Fig. 3 5. Starting at the top and working your way down pull out on the trim bezel to release the fasteners securing it. Once the bezel is completely detached from the dash it is not necessary to disconnect any of the wiring or the HVAC linkage. Simply allow the bezel to rest on the console to allow access to the screws securing the radio. Fig. 4 6.
12. Place the amp on top of the bracket by sliding it under the dash past the brake pedal. Make sure the connecters on the amp are facing toward the fire wall and the mounting holes are facing down. 13. Using a Torx® T-25 screwdriver install the four supplied screws and washers to attach the amp to the amp bracket. Fig. 9 14. Pass the factory radio harness connecter behind the metal framework indicated by the arrow. Fig. 10 15.
19. Remove the two 1Omm bolts temporarily installed in step 11. Position the previously removed metal plate over the top of the amp bracket and secure both with the two 1Omm bolts. 20. Tighten the bottom bolt. 21. Loosen the four screws indicated by the arrows in Fig. 12 approximately 4 turns. Fig. 12 22. Remove the screw indicated by arrow A completely. Fig. 12 23. Install the amplifier with the long tab toward the center of the car.
31. Gently pull the kick panel/sill plate toward the brake pedal to release the fasteners securing it. 32. Connect the ten pin connector of the harness to the amplifier. Slide the red locking tab over to prevent the connector from accidentally coming disconnected. 33. Route the harness along the bottom of the front and rear door jam and toward the back seat. 34. Connect the two pin connector of the amplifier harness to the two pin connector of the subwoofer harness. 35.
41. Set the subwoofer in place and connect the wire harness. 42. Align the mounting bracket with the anchor points at the bottom of the seat and press the enclosure down until it locks into place. Fig. 20 43. To remove the subwoofer press the tabs on each side of the mounting bracket while lifting up. Disconnect wiring. Fig. 21 44. Reinstall all previously removed parts in reverse order. 45. Reinstall supplied fuses in the fuse holders under hood .
Troubleshooting the Kicker Integrated Systems If you experience a problem once the Subwoofer is installed use this guide to locate the trouble. The radio is working, but the Subwoofer is not working: • • • • • • • • Check the battery voltage to make sure it is not discharged below 11 volts. Check the negative battery cable to see if it has been securely tightened back on the battery. Check the in line fuse located near the battery to make sure it is plugged in completely, and not blown.
No Subwoofer Output Radio not coming on Radio comes on, but no sound from any speakers Signal input connector not connected properly Connect signal wire of subwoofer harness to signal wire of amplifier harness or factory speaker wire depending on application. Check for loose connection Balance or fader controls not set to neutral position Set balance and fader control to center ~~;tings.
IMPORTANT: Please note that the stated fuse ratings included in the instructions are incorrect. The fuse(s) included in this kit are rated at 30A. Remember to also place your warranty card in the glove box fo·r future use.
f5(fKICKER(fKICKERrfKICKER(fKICKERrfKICKERrfKICKERrfKICKERrfKICKERrfKICKERrfKICKERrfKICKERrfKICKE~ ~ i ~ ~ Limited Warranty I ~ u ~ ~ ~ ~ ~ u ~ ~ ~ ~ ~ ~ ~ ~ ~ ~ ~ ~ ~ ~ ~ fOUnD fl:agEf~ ~ by{fKICKER ~ Audio System Upgrade ~ Please retain this card and your receipt with vehicle Contains valuable information should you need service ~ ~ ~ ~ ~ ~ ~ m PWRA207 u ~ ~ ~ ~ u~ ~ ~ m ffi ~ ~~~~~~~~~~~~.~m~~~~~~~~~~~.~m~~~~~~~~~~~.
ftj{fKICKER{fKICKER{fKICKER{fKICKER{fKICKER{fKICKER{fKICKER{fKICKER{fKICKER{fKICKER{fKICKER{fKICKE~ ~ U ~ n~ LIMITED WARRANTY ~ When purchased from an Authorized KICKER Dealer, KICKER warrants this product to be free from defects in material and workmanship under normal use for a period of ONE (1) YEAR from date of original purchase, or TWO (2) YEARS if installed by a KICKER dealer.
