LIVIN’ LOUD ZX AMPLIFIER ZX700.5 English Version Versión Español Amplificador del la Serie ZX.5 Deutsche Version Stereoverstärker der ZX.5-Serie Version Francaise Amplificateur de série ZX.5 2011 ZX 700.5 RevB.
ZX.5-SERIES AMPLIFIERS Owner’s Manual MODEL: ZX700.5 Authorized KICKER Dealer: Purchase Date: Model Number: Serial Number: PERFORMANCE RMS Power: AMP1 & AMP2 channels driven @ 14.4V, 4Ω stereo, 1% THD+N @ 14.4V, 2Ω stereo, 1% THD+N @ 14.4V, 4Ω mono, 1% THD+N 70W x 4 85W x 4 165W x 2 RMS Power: SUBWOOFER channel driven @ 14.4V, 4Ω mono, 1% THD+N @ 14.
The ZX amplifier has dual input sensitivity differential RCA inputs which will receive either high or low level signals from your car stereo’s source unit. A high-level signal can be run from the source unit’s speaker outputs to the stereo RCA input on the end panel of the amplifier using the KICKER ZISL as shown (make sure you set the ZX amplifier’s input level switch to “HI”). Alternatively, the signal can be delivered to the amplifier using the low-level RCA outputs on the source unit.
FOUR CHANNEL OPERATION with SUBWOOFER minimum impedance of 2 ohms per channel (AMP1, AMP2, and SUB channels) signal in AUTO TURN ON +12V DC L AUDIO XOVER1 XOVER2 OFF OFF HI R AMP1 1 L R SUB INPUT LEVEL FADER INPUT HI L AMP2 LO HI OFF ON AMP2 SUB R 2 SUB L+ L- R+ R- REMOTE BASS + SUB - signal in woofer ZXRC* REMOTE BASS INSTALLATION 2. slide the housing until it snaps into the metal bracket back view 1.
OPERATION AUTO TURN ON +12V DC L AUDIO XOVER1 XOVER2 OFF OFF HI R R INPUT SUB LEVEL FADER INPUT HI AMP1 INPUT 1 L L AMP2 INPUT LO HI OFF ON AMP2 SUB R 2 L+ L- R+ R- SUB INPUT REMOTE BASS + SUB - Automatic Turn-On Selection: The ZX series offers three different automatic turn-on modes that can be selected on the end panel; +12V, DC Offset, and Audio. Using either the DC Offset or Audio mode causes the REM terminal to have +12V out for turning on additional amplifiers.
TROUBLESHOOTING If your amplifier does not appear to be working, check the obvious things first such as blown fuses, poor or incorrect wiring connections, incorrect setting of crossover switch and gain controls, etc. There is an illuminated red badge on top of the amplifier denoting the power state of the amp in addition to the Protection LED on the end panel of your KICKER ZX series amplifier. When the red badge is lit, this indicates the amplifier is turned on and the amplifier is functioning properly.
CAUTION: When jump starting the vehicle, be sure that connections made with jumper cables are correct. Improper connections can result in blown amplifier fuses as well as the failure of other critical systems in the vehicle. If you have more questions about the installation or operation of your new KICKER product, see the Authorized KICKER Dealer where you made your purchase. For more advice on installation, click on the SUPPORT tab on the KICKER homepage, www.kicker.com.
AMPLIFICADOR DE LA SERIE ZX.5 Manual del propietario MODELO: ZX700.5 Distribuidor autorizado de KICKER: Fecha de compra: Número de modelo del amplificador: Número de serie del amplificador: RENDIMIENTO Potencia RMS: AMP1 y AMP2 canales activados @ 14.4V, 4Ω estereofónico, 1% THD+N @ 14.4V, 2Ω estereofónico, 1% THD+N @ 14.4V, 4Ω monofónico, 1% THD+N 70W x 4 85W x 4 165W x 2 Potencia RMS: SUBWOOFER canale activado @ 14.4V, 4Ω monofónico, 1% THD+N @ 14.
El amplificador ZX tiene entradas RCA diferenciales de doble sensibilidad de entrada que reciben señales de alto nivel o bajo nivel de la unidad fuente del sistema estereofónico del automóvil.La señal se puede llevar al amplificador desde las salidas de altavoz de alto nivel de la unidad fuente. Fije el selector de nivel de entrada del panel de extremo del amplificador en la posición de alto (HI).
FUNCIONAMIENTO POR CUATRO CANALES CON SUBWOOFER impedancia mínima de 2 ohmios por canales (AMP1, AMP2, y SUB canales) señal de entrada AUTO TURN ON +12V DC L AUDIO XOVER1 XOVER2 OFF OFF HI R AMP1 1 L R INPUT SUB LEVEL FADER INPUT HI L AMP2 OFF ON LO HI AMP2 SUB R 2 SUB L+ L- R+ R- REMOTE BASS + SUB - señal de entrada woofer ZXRC* CONTROL REMOTO DE BAJOS INSTALACIÓN 2. deslice el alojamiento hasta que encaje en el soporte de metal vista desde atrás 1.
FUNCIONAMIENTO AUTO TURN ON +12V DC L AUDIO XOVER1 XOVER2 OFF OFF HI R R SUB INPUT LEVEL FADER INPUT HI AMP1 INPUT 1 L L AMP2 INPUT LO HI OFF ON AMP2 SUB R 2 L+ L- R+ R- SUB INPUT REMOTE BASS + SUB - Selección de Encendido Automático: La serie ZX ofrece tres modalidades de encendido automático que se pueden seleccionar en el panel de extremo: +12V, compensación de CC y audio.
Control de Crossover: El crossover variable ubicado en la parte de arriba del amplificador permite ajustar la frecuencia de crossover de 50 a 200 Hz. La configuración de este control es subjetiva; 80 Hz es un buen punto de partida. Control Remoto de Bajos-ZXRC (no incluido): Con el control remoto de bajos, el nivel de salida del amplificador se puede controlar a distancia. Para montar el control remoto de bajos, atornille el soporte de metal en el lugar escogido.
¿Hay mala imagen estereofónica o baja respuesta de bajos? Revise la fase del sistema girando el control de balance de izquierda a derecha. Si hay más salida de bajos cuando se pasa a uno de los dos lados, revise el cableado de altavoz, las redes de crossovers pasivos y las terminales de altavoz para asegurarse de que tengan las conexiones positivas y negativas correctas.
VERSTÄRKER DER ZX.5 SERIE Benutzerhandbuch ZX700.5 MODELL: Autorisierter KICKER-Händler: Kaufdatum: Verstärker-Modellnummer: Verstärker-Seriennummer: LEISTUNG RMS-Leistung: AMP1 & AMP2 Kanäle betrieben @ 14.4V, 4Ω stereo, 1% Gesamtklirrfaktor @ 14.4V, 2Ω stereo, 1% Gesamtklirrfaktor @ 14.4V, 4Ω mono, 1% Gesamtklirrfaktor 70W x 4 85W x 4 165W x 2 RMS-Leistung: SUBWOOFER Kanal betrieben @ 14.4V, 4Ω mono, 1% Gesamtklirrfaktor @ 14.
Der ZX-Verstärker hat zwei RCA-Eingänge mit Eingangsempfindlichkeits-Differential, die entweder Hoch- oder Niedrigpegelsignale vom Autoradio empfangen. Kann das Signal mit den Hochpegel-Lautsprecherausgängen am Autoradio an den Verstärker übertragen werden. Stellen Sie den Eingangspegelschalter an der Endplatte des Verstärkers auf „HI“.
VIERKANALBETRIEB MIT SUBWOOFER Minimal impedanz von 2 Ohm pro Kanal (AMP1, AMP2, und SUB Kanäle) Signaleingang AUTO TURN ON +12V DC L AUDIO XOVER1 XOVER2 OFF OFF HI R AMP1 1 L R SUB INPUT LEVEL FADER INPUT HI L AMP2 LO HI OFF ON AMP2 SUB R 2 SUB L+ L- R+ R- REMOTE BASS + SUB - Signaleingang Tieftöner ZXRC* BASSPEGELFERNBEDIENUNG INSTALLATION 2. Schieben Sie das Gehäuse ein, bis es in der Metallhalterung einrastet. 1.
BETRIEB AUTO TURN ON +12V DC L AUDIO XOVER1 XOVER2 OFF OFF HI R R INPUT SUB LEVEL FADER INPUT HI AMP1 INPUT 1 L L AMP2 INPUT LO HI OFF ON AMP2 SUB R 2 L+ L- R+ R- SUB INPUT REMOTE BASS + SUB - Automatische Einschaltung: Die ZX-Serie bietet drei verschiedene automatische Einschaltmethoden, die an der Endplatte gewählt werden können: +12V, DC Offset und Audio.
Basspegel-Fernbedienung-ZXRC (nicht inbegriffen). Mit der Basspegel-Fernbedienung können Sie den Ausgangspegel des Verstärkers per Fernbedienung kontrollieren. Um die Basspegel-Fernbedienung zu befestigen, schrauben Sie einfach die Metallhalterung am gewünschten Installationsort ein. Schieben Sie dann das Gehäuse in die Halterung, bis es einrastet. Stecken Sie das Kabel von der Fernbedienung in die „Remote Bass“-Buchse am Verstärkergehäuse.
Keine Fade-Funktion? Wenn Sie beide Gruppen von Niedrigpegel- (RCA) oder Hochpegeleingängen (Lautsprecherkabel) verwenden, muss die Fader-Taste gedrückt sein. Störung durch Erdung? KICKER-Verstärker sind mit den Autoradios aller Hersteller kompatibel. Manche Autoradios erfordern eventuell weitere Erdung, um Störungen am Audiosignal zu verhindern. Wenn Sie Probleme mit dem Autoradio haben, reicht es meist, ein Massekabel von den RCA-Ausgängen am Autoradio zur Karosserie zu verlegen.
AMPLIFICATEUR SÉRIE ZX.5 Manuel d’utilisation MODÈLE: ZX700.5 Revendeur agréé KICKER : Date d’achat : Numéro de modèle de l’amplificateur : Numéro de série de l’amplificateur : PERFORMANCES Puissance Efficace: AMP1 & AMP2 canaux en service @ 14.4V, 4Ω stereo, 1% THD+N @ 14.4V, 2Ω stereo, 1% THD+N @ 14.4V, 4Ω mono, 1% THD+N 70W x 4 85W x 4 165W x 2 RMS Power: SUBWOOFER canal en service @ 14.4V, 4Ω mono, 1% THD+N @ 14.
L’amplificateur ZX est doté de deux entrées RCA différentielles de sensibilité d’entrée qui reçoivent des signaux de haut ou bas niveau à partir de l’appareil source de la stéréo de votre voiture. Le signal peut être transmis à l’amplificateur en utilisant les sorties de haut-parleur de haut niveau sur l’appareil source. Réglez le commutateur de niveau d’entrée sur le panneau d’extrémité de l’amplificateur à la position « HI ».
FONCTIONNEMENT À QUATRE CANAUX AVEC CAISSON DE GRAVES impédance minimum de 2 ohms par canal (AMP1, AMP2, et le SUB canaux Entrée du signal AUTO TURN ON +12V DC L AUDIO XOVER1 XOVER2 OFF OFF HI R L AMP1 1 R INPUT SUB LEVEL FADER INPUT HI L AMP2 LO HI OFF ON AMP2 SUB R 2 SUB L+ L- R+ R- REMOTE BASS + SUB - Entrée du signal woofer ZXRC* TÉLÉCOMMANDE DU NIVEAU DES GRAVES INSTALLATION 2.
UTILISATION AUTO TURN ON +12V DC L AUDIO XOVER1 XOVER2 OFF OFF HI R R INPUT SUB LEVEL FADER INPUT HI AMP1 INPUT 1 L L AMP2 INPUT LO HI OFF ON AMP2 SUB R 2 L+ L- R+ R- SUB INPUT REMOTE BASS + SUB - Sélection de Mise sous Tension Automatique : La série ZX est dotée de trois modes différents de mise sous tension automatique pouvant être sélectionnés au panneau d’extrémité de l’amplificateur : +12V, DC Offset (décalage c.c.) et Audio.
Télécommande du Niveau des Graves-ZXRC (non inclus) : La télécommande du niveau des graves permet de contrôler à distance le niveau de sortie de l’amplificateur. Pour monter la télécommande du niveau des graves, il suffit de visser le support métallique à l’emplacement choisi. Ensuite, faites glisser le logement sur le support jusqu’à ce qu’il s’enclenche en place. Faites passer le câble du contrôleur à la prise de la télécommande des graves (« Remote Bass ») sur le châssis de l’amplificateur.
Mauvaise image stéréo ou réponse réduite des graves ? Vérifiez le phasage du système en tournant le bouton de commande de balance de gauche à droite. Si la sortie des graves augmente lorsque vous tournez le bouton d’un côté ou de l’autre, vérifiez le câblage des haut-parleurs, les réseaux de filtrage passif et les bornes des haut-parleurs pour déterminer si les branchements positifs et négatifs sont corrects.
ELECTRONICS LIMITED WARRANTY KICKER warrants this product to be free from defects in material and workmanship under normal use for a period of THREE (3) MONTHS from date of original purchase with receipt. When purchased from an Authorized KICKER Dealer it is warranted for TWO (2) YEARS from date of original purchase with receipt. In all cases you must have the original receipt.
INTERNATIONAL WARRANTY Contact your International KICKER dealer or distributor concerning specific procedures for your country’s warranty policies. WARNING: KICKER products are capable of producing sound levels that can permanently damage your hearing! Turning up a system to a level that has audible distortion is more damaging to your ears than listening to an undistorted system at the same volume level.
©2010 Stillwater Designs 2011 ZX 700.5 RevB.