Cut Sheet

ManualsBrandsKidde Fire ManualsAC Operated120V AC/DC, Photo/Ion Dual Sensor wire-i

Dual Sensor, 120V AC with

Battery Backup Smoke Alarm

Model PI2010 Formerly Model PI2000

Dual Sensor

Contains both a photoelectric and ionization sensor

providing dual sensor protection in your home.

Hush

Feature

Temporarily silences nuisance alarms.

Battery Backup

Provides protection even during a power outage.

Red LED

Flashes every 30-40 seconds to indicate that

the smoke alarm is operating properly.

Test/Reset Button

Tests unit’s electronic circuitry and horn.

Description

The Kidde PI2010 is a 120VAC, wire-in smoke alarm with

9V battery backup. This smoke alarm functions as a stand

alone unit or in an interconnected system. The Kidde

PI2010 features Hush

, allowing you to quickly silence

nuisance alarms and also includes a tamper resist features

that deters tampering and theft. The PI2010 includes a

quick connect power harness that allows for quick and

easy installation.

This smoke alarm combines both photoelectric and

ionization sensors. Ionization sensing alarms may detect

invisible fire particles (associated with flaming fires) soon-

er than photoelectric alarms. Photoelectric sensing alarms

may detect visible particles (associated with smoldering

fires) sooner than ionization alarms.

Kidde strongly recommends that both ionization

and photoelectric smoke alarms be installed to help

insure maximum detection of the various types of

fire that can occur within the home.

The Kidde PI2010, 120VAC, wire-in smoke alarm

with 9V battery back up provides continuous protection

against smoke and fire hazards, even during power out-

ages. The combination of ionization and photoelectric

sensors offer the best protection against both fast flam-

ing and slow smoldering fires. The Kidde PI2010 inter-

connects with up to 24 Kidde devices of which 18 can be

initiating. This unit also includes flashing LEDs to signal

the alarm is functioning properly, a low battery warning

and a loud 85dB alarm. The Kidde PI2010 is UL Listed

and includes a 10-year limited warranty.

Features and Benefits

• Ionization Sensor – may detect invisible fire

particles (associated with flaming fires) sooner

than photoelectric alarms.

• Photoelectric Sensor – may detect visible particles

(associated with smoldering fires) sooner than

ionization alarms.

• Interconnect – Interconnects with up to 24

Kidde devices on one wiring network of which

18 can be initiating.

• Battery Backup (9V battery included) – Provides

continuous protection even during power outages.

• Tamper Resistant – Deters from tampering or theft.

• Hush

Feature – Temporarily silences nuisance alarms.

• Red LED – Flashes every 30-40 seconds to indicate

that the smoke alarm is operating properly.

• Test/Reset Button – Tests smoke alarm circuitry

and horn.

Summary of content (2 pages)

PAGE 1
Dual Sensor, 120V AC with Battery Backup Smoke Alarm Model PI2010 Formerly Model PI2000 Dual Sensor Contains both a photoelectric and ionization sensor providing dual sensor protection in your home. Hush® Feature Temporarily silences nuisance alarms. Battery Backup Provides protection even during a power outage. Red LED Flashes every 30-40 seconds to indicate that the smoke alarm is operating properly. Test/Reset Button Tests unit’s electronic circuitry and horn.
PAGE 2
Dual Sensor, 120V AC with Battery Backup Smoke Alarm Model PI2010 Formerly Model PI2000 Architectural and Engineering Specifications Installation of Smoke Alarm The smoke alarm should be installed to comply with all local codes having jurisdiction in your area, Article 760 of the National Electric Code, and NFPA 72. Make certain all alarms are wired to a single, continuous (non-switched) power line, which is not protected by a ground fault interrupter. A maximum of 1000 ft.