Owners manual

ManualsBrandsKidKraft ManualsBabyLimited Edition Toy Box - Cherry

Limited Edition Toy Box

Assembly Instructions

Item #14101- 14181

PARTS LIST:HARDWARE:

K. Nut x 2 pcs

J. Bolt x 2 pcs

x 2pcs

8 9

Small Allen

Wrench x 1 pc

Large Allen

Wrench x 1 pc

(1 1/4 in, 32 mm)

IMPORTANT: Lid support mechanism (Part I) must be

installed properly (Step 2,8) or a head/neck entrapment may

exist. Check to make sure the Lid Support is properly

installed by moving it back and forth. When you let go of the

lid it should stop, not fall or slam shut.

A. Cross Dowel Bolt

x 10 pcs

(2 5/8 in, 67 mm)

B. Cross Dowel Nut

x 10 pcs

C. Screw x 4 pcs

( 5/8 in, 15mm)

D. Spring Washer

x 4 pcs

E. Wood Dowel

x 2 pcs

F. Small Washer

x 2 pcs

G. Large Washer

x 4 pcs

H. Caster x 4 pcs

I. Lid Hinge x 1 pc

Wrench x 1 pc

The following tool

(not included) is

required for assembly:

Phillips screwdriver

Step 3

Step 4

Step 5

Step 1

Step 2

Customer Service

1-800-933-0771

www.kidkraft.com

•Do not allow children to play inside with lid closed. In certain

situations, sufficient air may not be available for breathing.

IMPORTANT! DO NOT TIGHTEN

SCREWS OR BOLTS UNTIL

COMPLETELY ASSEMBLED.

USE AND MAINTENANCE:

-Use on level surfaces only

-Please check assembly at regular intervals, and frequently

tighten hardware if necessary. If maintenance is not carried out,

the product could cease to function properly

Please retain this information for future reference

To order replacement parts, please visit www.kidkraft.com

CAUTION: Adult Assembly Required. Hardware

contains small screws with sharp points. Keep

unassembled parts out of reach of small children.

WARNING: CHOKING HAZARD

Small parts and sharp points, not

suitable for children under 3 years.

Summary of content (3 pages)

PAGE 1
Limited Edition Toy Box Please retain this information for future reference HARDWARE: A. Cross Dowel Bolt x 10 pcs Item #14101- 14181 Assembly Instructions PARTS LIST: To order replacement parts, please visit www.kidkraft.com Step 2 Step 1 K. Nut x 2 pcs I 1 (2 5/8 in, 67 mm) B. Cross Dowel Nut x 10 pcs 2 Small Allen Wrench x 1 pc D. Spring Washer x 4 pcs E. Wood Dowel x 2 pcs F. Small Washer x 2 pcs G. Large Washer x 4 pcs 3 1 J G Large Allen Wrench x 1 pc 4 C.
PAGE 2
Limited Edition Toy Box Assembly Instructions Step 6 Item #14101- 14181 Step 7 C C C C F F B 9 E B Step 8 F B When you let go of the lid it should stop, not fall or slam shut. A B 8 I A A Check periodically to make sure the lid is not falling shut. If the lid is starting to slowly fall shut, adjust the braking tension (set screw) with a 4mm hex key until the lid will remain open when you let go of it. A CAUTION: Adult Assembly Required. Hardware contains small screws with sharp points.
PAGE 3
Warning: This is intended for children of a specific age or above. Keep children younger than the specified age from using this item. Do not let children of any age climb on or around this item. Adult supervision is always recommended. IMPORTANT INFORMATION - PLEASE READ FIRST ALL OF OUR WOODEN ITEMS ARE HANDCRAFTED, HAND ASSEMBLED, AND HAND PAINTED. EACH ONE IS UNIQUE. SLIGHT IMPERFECTIONS MAY OCCUR AND ARE NOT MANUFACTURING DEFECTS.