B I G B A C K YA R D P R E M I U M M A I N CLUBHOUSE AND SWING – F24900 INSTALLATION AND OPERATING INSTRUCTIONS WARNING To reduce the risk of serious injury or death, you must read and follow these instructions. Keep and refer to these instructions often and give them to any future owner of this play system. Manufacturer contact information provided below. FOR OBSTACLE FREE SAFETY ZONE AND MAXIMUM NUMBER OF USERS SEE - Fort Guides in Main Clubhouse and Swing or Add On C instructions.
B I G B A C K YA R D P R E M I U M M A I N CLUBHOUSE AND SWING – F24900 Montrose TUBE SLIDE 2-4 Hrs Two person assembly Required: F24900 - Main Clubhouse and Swing A24912 - High Rail Wave Slide A24913 - TNRIII Tube Slide FORTS Cloverdale Required: F24900 - Main Clubhouse and Swing A24908 - Add On B 10-14 Hrs A24913 - TNRIII Tube Slide Two person assembly Solowave Design 375 Sligo Rd.
Warnings and Safe Play Instructions CONTINUOUS ADULT SUPERVISION REQUIRED. Most serious injuries and deaths on playground equipment have occurred while children were unsupervised! Our products are designed to meet mandatory and voluntary safety standards. Complying with all warnings and recommendations in these instructions will reduce the risk of serious or fatal injury to children using this play system.
Protective Surfacing - Reducing Risk of Serious Head Injury From Falls One of the most important things you can do to reduce the likelihood of serious head injuries is to install shock-absorbing protective surfacing under and around your play equipment. The protective surfacing should be applied to a depth that is suitable for the equipment height in accordance with ASTM F1292.
Instructions for Proper Maintenance Your Big Backyard Play System is designed and constructed of quality materials with your child’s safety in mind. As with all outdoor products used by children, it will weather and wear. To maximize the enjoyment, safety and life of your Play Set, it is important that you, the owner, properly maintain it. Check the following at the beginning of the play season: GROUND STAKES (ANCHORS): Check for looseness, damage or deterioration.
About Our Wood Solowave Design™ uses only premium playset lumber, ensuring the safest product for your children’s use. Although great care has been taken in selecting the best quality lumber available, wood is a product of nature and susceptible to weathering (changes in the aesthetics of the wood). A light sanding may be required to remove minor splinters. For your information, we have described some changes that may occur as a result of weathering: 1.
Keys to Assembly Success Tools Required • Tape Measure • Carpenters Level • Carpenters Square • Claw Hammer • Standard or Cordless Drill Part Identification Key On each page, you will find the parts and quantities required to complete the assembly step illustrated on that page. Here is a sample.
5/16" (8mm) Flat Washer 1/4" (6mm) Lock Washer 5/16" (8mm) T-Nut 1/4" (6mm) T-Nut 1/4" (6mm) Flat Washer 5/16" (8mm) Flat Washer For example: BOLT LENGTH 4½ (4.5) inches long 1 inch = 25.4mm LENGTH CONVERSION 0.31 inches x 25.4mm = 8mm BOLT DIAMETER 5/16 (0.31) inches For example: 1 inch = 25.4mm DIAMETER CONVERSION HARDWARE LENGTH CHART inches vs millimetres 6 152 5½ 140 5 127 114 4½ 4 102 3½ 89 3 76 2½ 64 2 51 1½ 38 1¼ 32 1-1/8 29 1 25.4 7/8 22 3/4 19 1/2 12.
63.5 2 1/2" 5/4 x 3 88.9 3 1/2" 5/4 x 4 114.3 4 1/2" 5/4 x 5 139.7 5 1/2" 5/4 x 6 88.9 3 1/2" 4x4 38.1 1 1/2" 34.9 1 3/8" 34.9 1 3/8" 38.1 1 1/2" 38.1 1 1/2" 2x6 136.5 5 3/8" 2x4 85.7 3 3/8" 2x3 63.5 2 1/2" 2 x2 15.9 5/8" 82.6 3 1/4" 34.9 1 3/8" 60.3 2 3/8" 85.7 3 3/8" 114.3 4 1/2" 136.5 5 3/8" 1/2 x 4 1x2 1x3 1x4 1x5 1x6 LENGTH CONVERSION 1 inch = 25.4mm 59.25 inches x 25.4mm = 1505mm For example: BOARD LENGTH 59¼ (59.25) inches 15.9 5/8" 15.9 5/8" 15.9 5/8" 15.
Part Identification (Reduced Part Size) 1pc. - 2648 - 1 x 4 x 40-5/8" - Floor Board - Box 2 - 3632648 Nominal Size 5/4 x 5 5/4 x 6 8pc. - 2609 - 1 x 5 x 40-5/8" - Floor Board - Box 2 - 3632609 2x2 1x4 1x6 1-1/4 x 2-1/4 2pc. - 2605 - 1 x 6 x 19-3/4" - Access Board - Box 2 3632605 2pc. - 2717 - Clock Block 3/4 x 1-3/4 x 9-3/4" 1-1/4 x 3 4x4 Box 2 - 3632717 4x6 2pc. - 2603 - 1 x 6 x 19-3/4" - Rock Board A - Box 2 3pc.
Part Identification (Reduced Part Size) 1pc. - 2627 SW Wall Panel 1¼ x 42 x 87` Box 2 - 37632627 2pc. - 2618 Front Back Panel Box 2 - 37632618 1pc. - 2639 Back Roof Panel 1¼ x 36¾ x 44" Box 2 - 37632639 1pc. - 2644 Front Roof Panel 1¼ x 37 x 44" Box 2 - 37632644 2pc. - 2655 Upper Window Insert 1.27 x 18.8 x 35.86" Box 2 - 37632655 1pc. - 2622 End Panel Assembly 1¼ x 42 x 87" Box 2 - 37632622 1pc. MOD 3 Pane Transom (2Pk) Box 2 - 3320138 2pc. - 649A Short Half Wall - 1.27 x 18.
Hardware Identification (Actual Size) 5pc. LW2 - 5/16" Lock Washer - (51303300) 5pc. FW0 - 3/16" Flat Washer - (51103100) 10pc. TN1 - 1/4" T - Nut (54503200) 12pc. FW1 - 1/4" Flat Washer - (51103200) 8pc. TN2 - 5/16" T- Nut - (54503300) 15pc. LW1 - 1/4" Lock Washer - (51303200) 66pc. FW2 - 5/16" Flat Washer - (51103300) 29pc. LN2 - 5/16" Lock Nut - (54303300) 5pc. BN1 - 1/4" Barrel Nut - (54803200) 8pc. FW3 - #8 Flat Washer - (51003500) 5pc. PB2 - Pan Bolt 1/4 x 1-1/4" 1pc.
Hardware Identification (Actual Size) 16pc. WL5 - Wafer Lag 1/4 x 2-1/2" 3pc. WB7 - Wafer Bolt 5/16 x 3" - (53613330) - (52613222) 4pc. H1 - Hex Bolt 1/4 x 1-1/2" - (53703212) 2pc. H10 - Hex Bolt 1/4 x 2-1/4" - (53703221) 4pc. G8 - Hex Bolt 5/16 x 2" - (53703320) 4pc. H11 - Hex Bolt 1/4 x 2-3/4" - (53703223) 7pc. G21 - Hex Bolt 5/16 x 3-3/4" - (53703333) 3pc. G4 - Hex Bolt 5/16 x 4" - (53703340) 14pc. G7 - Hex Bolt 5/16 x 5-1/2" - (53703352) 2pc. LS3 - Lag Screw 1/4 x 3" - (52213230) 2pc.
Step 1: Inventory Parts - Read This Before Starting Assembly STOP A. STOP STOP STOP his is the time for you to inventory all your hardware, wood and accessories, T referencing the parts identification sheets. This will assist you with your assembly. • The wood pieces will have the four digit key number stamped on the ends of the boards. The wood pieces are referenced throughout the instructions with this number. • Please refer to Page 6 for proper hardware assembly.
Step 2: Frame Assembly Part 1 It is important to assemble the frame on a flat, smooth surface. A: Place (2627) SW Wall Panel between 2 (2618) Front Back Panels noticing the panel orientations. The tops and bottoms of the panels should be flush.
Step 2: Frame Assembly Part 2 B: Place (2622) End Panel Assembly between both (2618) Front Back Panels noticing the panel orientations. The tops and bottoms of the panels should be flush. Make sure the panels are square then using the pilot holes as a guide pre-drill with a 3/16” drill bit and fasten the back (2618) Front Back Panel to (2622) End Panel Assembly and (2622) End Panel Assembly to the front (2618) Front Back Panel with 4 (WL5) 1/4 x 2-1/2” Wafer Lags per side. (fig. 2.4) Back Swing Side Fig.
Step 3: Floor Assembly Part 1 A: From inside of the assembly centre (2608) Floor Joist over pilot holes in (2622) End Panel Assembly and (2627) SW Wall Panel, 5/8” down from the top of board then attach (2608) Floor Joist to each panel with 2 (S4) #8 x 3” Wood Screws per end. (fig.3.1, 3.2 and 3.3) S4 Fig. 3.1 2627 Top View 2608 Fig. 3.3 2608 S4 x 2 per side 2622 S4 2622 5/8” Fig. 3.
Step 3: Floor Assembly Part 2 B: On both (2618) Front Back Panels attach 1 (2610) Side Joist to the inside of each panel with 2 (H11) 1/4 x 2-3/4” Hex Bolts (with lock washer, flat washer and t-nut) and 4 (S3) #8 x 2-1/2” Wood Screws as shown in fig. 3.4 and 3.5. 2610 Fig. 3.4 2627 2618 2610 2618 2622 2610 Fig. 3.5 2618 1/4” Flat Washer 1/4” Lock Washer S3 1/4” T-Nut H11 S3 H11 S3 Hardware Wood Parts 2x 2610 Side Joist 2 x 2 x 40-1/4” •See details SIZE A DWG. NO.
Step 3: Floor Assembly Part 3 C: Starting at (2627) SW Wall Panel place (2648) Floor Board followed by 8 (2609) Floor Boards. Make sure all boards are evenly spaced then attach to (2608) Floor Joist and each (2610) Side Joist with 5 (S2) #8 x 1-1/2” Wood Screws per board. (fig. 3.6 and 3.7) 2627 2609 Fig. 3.6 2648 2622 Fig. 3.
Step 4: Attach SW Ground and Diagonal A: Loosely attach 1 (2606) SW Ground to each (2607) Diagonal with 1 (H10) 1/4 x 2-1/4” Hex Bolt (with lock washer, flat washer and t-nut) per board then place each (2607) Diagonal tight and flush to the front of (2627) SW Wall Panel. (2606) SW Grounds to be flush to the bottom of (2627) SW Wall Panel. (fig. 4.1 and 4.
Step 5: Swing Beam Assembly A: Attach 4 Swing Hangers to Fort End of (2614) Engineered Beam and 2 Glider Hangers to the Glider End using 2 (G7) 5/16 x 5-1/2” Hex Bolts (with 2 flat washers and 1 lock nut) per Swing Hanger and Glider Hanger, as shown in fig. 5.1. B: Flush to the Fort End of (2614) Engineered Beam attach 2 L-Beam Brackets with 2 (G21) 5/16 x 3-3/4” Hex Bolts (with 2 flat washers and 1 lock nut). (fig. 5.
Step 6: Swing End Assembly A: Loosely attach 2 (2613) Heavy SW Posts to (2615) SW Upright using 2 (G7) 5/16 x 5-1/2” Hex Bolts (with lock washer, flat washer and t-nut). Notice 2 bolt holes at top of (2615) SW Upright and orientation of angle. (fig. 6.1) B: Attach (2616) SW Support to both (2613) Heavy SW Posts and (2615) SW Upright using 3 (G4) 5/16 x 4” Hex Bolts (with lock washer, flat washer and t-nut). Tighten all bolts (fig. 6.
Step 7: Attach Swing End to Swing Beam A: Place Swing End Assembly against Swing Beam Assembly then place 1 Beam Bracket on each side of the assembly (they are specific for left and right side) and attach with 5 (G21) 5/16 x 3-3/4” Hex Bolts (with 2 flat washers and 1 lock nut). (fig. 7.1 and 7.2) Fig. 7.1 Swing Beam Assembly Beam Bracket Swing End Assembly Swing Beam Assembly Fig. 7.
Step 8: Attach Swing Assembly To Fort A: Place Swing Assembly against top of (2627) SW Wall Panel, make sure assembly is level then attach from inside the fort assembly into each L-Beam Bracket with 4 (G8) 5/16 x 2” Hex Bolts (with 2 flat washers and 1 lock nut). (fig. 8.1) L-Beam Bracket Fig. 8.1 2627 G8 Swing Assembly 5/16” Flat Washer 5/16” Lock Nut Hardware 4x G8 5/16 x 2” Hex Bolt (5/16” flat washer x 2, 5/16” lock nut) 24 support@solowavedesign.
Step 9: Install Ground Stakes MOVE FORT TO FINAL LOCATION PRIOR TO STAKING FINAL LOCATION MUST BE LEVEL GROUND A: In the 5 places shown in fig. 9.1 drive the Rebar Ground Stakes 13” into the ground against outside front corner of (2622) End Panel Assembly, on both (2607) Diagonals and both (2613) Heavy SW Posts. Be careful not to hit the washer while hammering stakes into the ground as this could cause the washer to break off. B: Attach ground stakes using 1 (S7) #12 x 2” Pan Screw per ground stake (fig. 9.
Steps 10 - 23 show how to assemble and install add-ons and inserts. Fort Guides show where to install them. FORT GUIDES: Page 48-49: Brooksville Page 50-51: Halliwell, Opt. 1 Page 52-53: Halliwell, Opt. 2 Page 54-55: Cloverdale Page 56-57: Montrose 26 support@solowavedesign.
Step 10: How to Install Inserts - Upper and Lower Jambs There is 1 (2601) Lower Jamb and 1 (2602) Upper Jamb provided with the Main Clubhouse and Swing. Depending on which fort you have purchased determines where they are installed on the (2622) End Panel Assembly or (2618) Front Back Panel, see Fort Guide. See below for different variations and how to attach the Jambs to the Panel. When installing you will need 2 Jamb Mounts per Jamb and 4 x (S0) #8 x 7/8” Truss Screws per Jamb Mount.
Step 11: How to Install Inserts - Window and Wall Inserts Part 1 There is 1 (2649) Lower Window Insert, 2 (2655) Upper Window Inserts, 1 (2665) Half Wall Insert, 2 (649A) Short Half Walls and 2 MOD 3-Pane Transoms provided with the Main Clubhouse and Swing. Depending on which fort you have purchased determines where they are installed, see Fort Guide. See below for how to attach each insert.
Step 11: How to Install Inserts - Window and Wall Inserts Part 2 Inside Views MOD 3-Pane Transom Tight 649A S0 2665 S0 Tight S0 Tight SIZE DWG. NO. REV. INSERTtoPANELAPREP A Flanges Details Use 5- #8 x 7/8" Truss to attach Window + 4 -#8 x 7/8" to attach SCALE:1:50 WEIGHT: SHEET 1 OF 1 WEIGHT: SCALE:1:50 SHEET 2 OF 2 wall panel ( first, install middle screw at top of Window) 29 support@solowavedesign.
Step 12: How to Install Inserts - Clock Assembly There is 1 Clock Set provided with the Main Clubhouse and Swing. Depending on which fort you have purchased determines where it is installed, see Fort Guide. See below for how to assemble and attach the Clock Set. When installing you will need the following: Base Clock, Clock Subset (includes minute and hour hands, clock adapter and clock screw), 2 (2717) Clock Blocks and 4 x (S2) #8 x 1-1/2” Wood Screws.
Step 13: Rock Wall Assembly Fig. 13.1 0349 2603 2603 2604 Note: The holes in the rock boards must orient to the top of the boards. 2604 2605 2604 S2 7-5/8” Approx x 4 per board Note: Gaps between boards 2-1/4”, not to exceed 2-3/8” Fig. 13.2 A: Lay 2 (0349) Rock Rails down, side by side with angled edges facing down. (fig. 13.1) B: Place (2605) Access Board on the bottom of each (0349) Rock Rail as shown in fig. 13.1.
Step 14: Attach Rock Wall Assembly to Fort Part 1 A: Place Rock Wall Assembly centred in opening shown on the Fort Guide and flush as shown below. Attach (0349) Rock Rails panel using 4 (S11) #8 x 2” Wood Screws. (fig. 14.1 and 14.2) B: Attach 1 (2605) Access Board to top of Rock Wall Assembly, flush to top of (0349) Rock Rail using 4 (S2) #8 x 1-1/2” Wood Screws. (fig. 14.3) Fig. 14.2 Fig. 14.1 S11 Panel Panel Flush S11 S11 0349 0349 Fig. 14.
Step 14: Attach Rock Wall Assembly to Fort Part 2 C: Drive 1 Rebar Ground Stake 13” into the ground against outside (0349) Rock Rail then attach with 1 (S7) #12 x 2” Pan Screw. Be careful not to hit the washer while hammering stake into the ground as this could cause the washer to break off. (fig. 14.4 and 14.5) D: After driving stake into the ground, check for sharp edges caused by the impact of the hammer. Smooth any sharp edges from impact area and touch up with outdoor paint.
Step 15: Cafe Table Assembly A: Place (2612) Table Support flush to the notched out ends of (2611) Table Top and attach with 4 (S7) #12 x 2” Pan Screws as shown in fig. 15.1. B: Place Table Top Assembly tight in the opening of panel as shown in Fort Guide then attach (2612) Table Support to the panel with 2 (S3) #8 x 2-1/2” Wood Screws. (fig. 15.2) Note: For the Cloverdale the Cafe Table is installed from the inside of the fort on the (2627) SW Wall Panel. (fig. 15.3) S7 Fig. 15.1 2612 Flush 2611 Fig.
Step 16: Attach Cafe Canopy to Fort See note below before starting this step. A: Feed Cafe Canopy Frame through the pocket of the Cafe Canopy. (fig. 16.1) B: With a helper hold the Canopy against the fort, on the panel shown on the Fort Guide, measure 3-1/8” in from the outside edge of the post, making sure the Cafe Canopy is smooth and tight then attach to the panel with 2 (S5) #8 x 1/2” Pan Screws (with #8 flat washer), measure 1-1/2” down from the first screw then attach a third screw and washer.
Step 17: Attach Slide to Fort Please note this slide is not used on the Cloverdale Fort, please skip this step and refer to the instructions in the TNRIII Tube Slide box for assembly and installation. A: Place Slide in the centre of the opening at the front of the fort as shown in the Fort Guide, pre-drill with a 1/8” drill bit then attach slide to fort through the (2618) Front Back Panel using 3 (S7) #12 x 2” Pan Screws. (fig. 17.1 and 17.2) Fig. 17.1 S7 Slide S7 Fig. 17.
Step 18: Glider Assembly A: Attach 1 Space Glider Handle to the Space Glider Body using 1 (G25) 5/16 x 7-1/4” Hex Bolt (with 2 flat washers and 1 lock nut). Repeat for the second Space Glider Handle. (fig. 18.1) B: Install 2 Glider Rope with Chains into each Space Glider Handle using 2 - 5/16” Flat Washers and 1 Lock Nut per rope. (fig. 18.1) Fig. 18.
Step 19: Roof Support Assembly A: Attach 1 (2617) Roof Support to a second (2617) Roof Support at peak using 1 (S4) #8 x 3” Wood Screw. Repeat this step so there are 2 Roof Support Assemblies. (fig. 19.1 and 19.2) Roof Support Assembly Fig. 19.1 S4 2617 Fig. 19.2 S4 2617 Wood Parts 4x 2617 Roof Support 1-1/4 x 2-1/4 x 37-1/2” Hardware 2x S4 #8 x 3” Wood Screw 38 support@solowavedesign.
Step 20: Roof Assembly Part 1 A: Place (2644) Front Roof Panel against (2639) Back Roof Panel so the tops form a peak then tight to the inside edge of the outside slats attach 1 Narrow Angle Bracket per slat with 2 (S0) #8 x 7/8” Truss Screws per bracket. (fig. 20.1 and 20.2) B: Attach the third Narrow Angle Bracket centred on the middle slat with 2 (S0) #8 x 7/8” Truss Screws. (fig. 20.1 and 20.3) Centred Fig. 20.3 Narrow Angle Bracket Flush Fig. 20.
Step 20: Roof Assembly Part 2 C: Place 1 Roof Support Assembly against one side so the peaks meet and the ends of the roof supports are flush with the ends of the roof panels. Attach with 6 (S11) #8 x 2” Wood Screws. (fig. 20.4) D: Attach the second Roof Support Assembly on the opposite side, peaks to meet and ends are flush with 6 (S11) #8 x 2” Wood Screws. (fig. 20.4) S11 Fig. 20.
Step 21: Attach Sky Gable A: Attach 1 Sky Gable to the inside of the (2617) Roof Supports on each side of the Roof Assembly with 4 (S5) #8 x 1/2” Pan Screws per Sky Gable. (fig. 21.1 and 21.2) Sky Gable Fig. 21.1 2617 2617 Roof Assembly Sky Gable 2617 Fig. 21.2 S5 S5 SIZE DWG. NO. A Roof -Gable Connect •Attach Gable to inside Roof Supports with #8 x 1/2 Pan Screws •Repeat for other side Sky Gable SCALE:1:50 WEIGHT: REV.
Step 22: Attach Roof Ends Part 1 Use the reference guides below to determine where the (2646) Roof End and (2647) Roof End Left are attached. For Cloverdale use Ref #1 and TNRIII Tube Slide must be assembled and attached first. For Brooksville and Halliwell use Ref #2.
Step 22 Part 2: For Halliwell,Opt. 2 and Montrose Attach Cafe Canopy to Fort B: Feed Cafe Canopy Frame through the pocket of the Cafe Canopy. (fig. 22.3) C: With a helper hold the Canopy against the top of the Front Wall so it sits in the centre of the wall and the edge of the canopy is flush to the inside of (2618) Front Back Panel.
Step 23: Attach Roof Assembly to Fort A: With 2 people on the ground and at least 1 person in the fort, lift the Roof Assembly up and over the Back side of the fort. Guide the Roof Assembly onto the fort so all four (2617) Roof Supports sit flush to the front and outside edges of (2646) Roof End and (2647) Roof End Left. (fig. 23.1 and 23.2) B: Attach (2617) Roof Supports to (2646) Roof End and (2647) Roof End Left with 1 (S3) #8 x 2-1/2” Wood Screw per support. (fig. 23.2) Fig. 23.
Step 24: Bench Assembly A: Open the (2658) Folding Bench Assembly. (fig. 24.1, 24.2 and 24.3) B: Make sure assembly is level then secure with 2 (H1) 1/4 x 1-1/2” Hex Bolts (with lock washer, flat washer and t-nut) per side. (fig. 24.4) C: Tighten the top screws in all 4 Bench Legs. (fig. 24.4) Bench Legs Fig. 24.1 2658 Fig. 24.3 Fig. 24.2 Bench Legs Tighten these screws - all 4 legs Fig. 24.
Step 25: Attach Belt Swings and Glider Warning! Check entire play centre for bolts protruding beyond t-nuts. Use extra washers to eliminate this condition. A: Attach 2 Belt Swings and assembled Space Glider to the hangers then tighten all Quick Links with an adjustable wrench. (fig. 25.1 and 25.2) Quick Link Fig. 25.1 Fig. 25.2 Tighten Clip using adjustable wrench Belt Swings Space Glider Other Parts 2 x Belt Swings 46 support@solowavedesign.
WARNING & I.D. PROMINENT Final Step: Attach I.D. Plaque YOUR PLAY ort or Swing Post) ATTACH THIS WARNING & I.D. PLAQUE TO THIS LOCATION ON YOUR PLAY rnings concerning EQUIPMENT! ant contact acking Number This provides warnings concerning safety and ow you to get critical important contact information. A Tracking Number der replacement parts is provided to allow you to get critical information or order replacement parts for this specific model. model. A: Attach Big Backyard I.D.
Fort Guide: Brooksville MOD 3-Pane Transom 2618 2655 Front 17” 17” 2618 2601 2655 Clock Set MOD 3-Pane Transom Slide Position 2601 Clock Set 2649 Slide sold separately Front Installation 2649 649A 2622 17” 2602 17” 2622 2665 Cafe Canopy Set 2602 Cafe Table Assembly 649A Left Side Installation Cafe Canopy Set Cafe Table Assembly 2665 48 support@solowavedesign.
Fort Guide: Brooksville MOD 3-Pane Transom 2655 Back MOD 3-Pane Transom 2618 2655 2618 Rock Wall Assembly Back Installation Rock Wall Assembly Position Roof Installation Roof Assembly with Sky Gables 2647 1 per side 2646 1 per side Maximum Number of Users: 10 49 support@solowavedesign.
Fort Guide: Halliwell - Opt. # 1 MOD 3-Pane Transom 2618 2649 649A 2601 Front 17” 17” 2618 Rock Wall Assembly Position 2601 649A MOD 3-Pane Transom Slide Position Rock Wall Assembly Front Installation Slide sold separately 2649 2655 Clock Set 17” 2622 17” 2602 2655 2665 Cafe Canopy Set 2602 2622 Cafe Table Assembly Left Side Installation Clock Set Cafe Canopy Set Cafe Table Assembly 2665 50 support@solowavedesign.
Fort Guide: Halliwell - Opt. # 1 2618 649A Back Monkey Ladder Assembly Monkey Ladder Position 649A Back Installation Monkey Ladder instructions are in the Add-On A box (A24905) 2618 Roof Installation Roof Assembly with Sky Gables 2646 1 per side 2647 1 per side Maximum Number of Users: 12 51 support@solowavedesign.
Fort Guide: Halliwell - Opt.
Fort Guide: Halliwell - Opt. # 2 2618 MOD 3-Pane Transom Rock Wall Assembly 2655 Back MOD 3-Pane Transom Rock Wall Assembly 2655 2618 Back Installation Roof and Swing Installation Swing Assembly Roof Assembly with Sky Gables 28'-9" 16'-9" 11'-5" 27'-0" HALLIWELL2 H: same as BBY Premiums Maximum Number of Users: 12 53 support@solowavedesign.
Fort Guide: Cloverdale 2655 2618 17” Front 2655 2601 17” 2715 2618 Door Assembly Door Assembly instructions are in the Add-On B box (A24908) Cafe Canopy Set Door Assembly 2649 Clock Set 2649 Cafe Canopy Set Front Installation 2601 8935 MOD Side Lite Clock Set 2622 2602 9-5/8” 2622 2665 2602 TNR III Tube Slide instructions are in A24913 TNR III Tube Slide Position TNR III Tube Slide 8935 Left Side Installation 54 MOD Side Lite 2665 support@solowavedesign.
2618 Fort Guide: Cloverdale MOD 3-Pane Transom 649A Cafe Table Assembly Back 17” MOD 3-Pane Transom 17” 2601 2618 649A 2649 649A Rock Wall Assembly Position Back Installation Rock Wall Assembly 2649 649A 2601 Roof Installation Roof Assembly with Sky Gables 2646 1 per side 2647 1 per side Maximum Number of Users: 10 55 support@solowavedesign.
Fort Guide: Montrose 2618 Cafe Canopy Set MOD 3-Pane Transom Front 17” 17” Cafe Canopy Set Slide Position 2601 MOD 3-Pane Transom 649A 649A Slide Position 2649 2618 2601 Rock Wall Assembly 2649 Front Installation 2622 2602 MOD Side Lite 9-5/8” 8935 Left Side 2602 MOD Side Lite TNR III Tube Slide Position TNR III Tube Slide instructions are in A24913 TNR III Tube Slide 8935 Cafe Table Assembly (use directions for Cloverdale in Step 15, Fig. 15.
Fort Guide: Montrose 2618 Back 2655 2655 2618 Clock Set Clock Set 2655 Back Installation Roof and Swing Installation Roof Assembly with Sky Gables Swing Assembly 28'-8" 16'-8" 11'-5" 27'-0" MONTROSE H: Maximum Number of Users: 10 57 support@solowavedesign.
NOTES NOTES 58 support@solowavedesign.
NOTES NOTES 59 support@solowavedesign.
BIG BACKYARD Consumer Registration Card First Name Initial Last Name Street Apt. No.
