Instruction Manual

2021
TM
TO PLAY
3. Insert new 6 x AA (1.5V) batteries into the battery compartment
of the control box with the correct polarity (+/—).
4. Close the battery cover.
Make sure that the wheel tyres are located as shown.
Make sure that the brushes are adjusted to the correct position as indicated.
1. Unscrew the screw on
the battery cover.
2. Open the battery cover.
5. Tighten the screw on the battery cover.
Guide pin
Guide pin must be in the slot as shown. Check the brushes of the car are in the correct position.
Place the car on the track and make sure it has good contacts with the track.
ON
(USE AA BATTERIES)
DC
(USE Transformer)
OFF
NO. 83151 / 83161
Transformer
For Control Box
(Included only for #83161)
KT-HW-27/05/21 EN
MAINTENANCE
PRODUCT: SLOT CAR TRACK SET
AGE GRADE: For ages over 5 years.
CONTENTS: All contents listed here.
The packaging and instruction manual contain important information. Please keep them for future reference. We reserve the right to improve/amend
specifications and colors without notice.
Conforms to the safety requirements of ASTM F963
SAFETY
PRODUCT MUST BE ASSEMBLED BY ADULT ONLY.
Environmental notes:
Disposal of batteries
Batteries should not be disposed of in the household waste. As the consumer you are legally obliged to return
batteries containing harmful substances and all other used batteries. You can hand in your old batteries at
public collection points in your area or wherever batteries are sold.You will find these chemical abbreviations
along with a crossed-out refuse bin on batteries containing harmful substances:
Pb=Battery contains lead
Cd=Battery contains cadmium
Hg=Battery contains mercury
The whole product also does not belong to household waste at the end of the product life.
You can return it at collection points for the recycling of electronic and electronical instruments
The symbol on the item, instruction manual, hangtag or packing is showing this clearly.
Materials should be recycled according to their respective markings.
Recycling of old devices or other re-use of materials contained therein represents an important contribution to environmental protection.
Please ask at your local community for the correct collection point.
8. Be sure to insert batteries with correct polarities and always follow the
battery manufacturer’s instructions
9. Remove all batteries when not in use
10. Exhausted batteries are to be removed from the product
11. The supply terminals are not to be short-circuited
12. Dispose of batteries properly. Do not dispose the batteries in fire – it may cause
them to explode or leak causing injury or damage
13. Battery installation and removal must only be done by adult
1. Alkaline batteries are recommended to be used (For B/O Version)
2. Only batteries of the same or equivalent type as recommended
are to be used
3. Do not mix alkaline, standard or rechargeable batteries
4. Do not mix old and new batteries or different type of batteries
5. Non-rechargeable batteries are not to be charged
6. Rechargeable batteries for adult charging only
7. Rechargeable batteries are to be removed from the product before they
are charged
BRUSHES
The instructions for battery toys with replaceable batteries shall contain the substance of the following, as applicable:
Control box : AA batteries x 6 should be used. Transmitter : AAA batteries x 4 (2 for each Transmitter) should be used.
Speed Control
1. Unscrew the screw on the battery cover.
2. Open the battery cover.
3. Insert new 2 x AAA (1.5V) batteries into
the battery compartment of each transmitter
with the correct polarity (+/—).
4. Close the battery cover.
5. Tighten the screw on the battery cover.
FCC label compliance statement:
This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions:
1. This device may not cause harmful interference, and
2. This device must accept any interference received, including interference that may cause undesired operation. Note: This equipment has been tested and
found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used
in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in
a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment
off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna
- Increase the separation between the equipment and receiver
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected
- Consult the dealer or an experienced radio/TV technician for help
Warning: Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user’s authority to operate the
equipment.
RSS-210 Compliance Statement:
This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canada’s licence-exempt RSS(s).
Operation is subject to the following two conditions:
(1) This device may not cause interference.
(2) This device must accept any interference, including interference that may cause undesired operation of the device
.
ion.
Declaration of Conformity
The product is in conformity with the requirement of EU Directive 2014/53/EU
Transmitter - Battery installation
Control box - Battery installation (For B/O Version)
www.kidztechtoys.com
KIDZTECH TOYS MANUFACTURING LTD.
Room 802, 8/F, Inter-Continental Plaza,
94 Granville Road, TST East, Hong Kong.
Tel: [phone] [e-mail]
Made in China http://www.kidztechtoys.com
US OFFICE:
1540 Forest Avenue,
River Forest, IL 60305, USA
Tel: [phone] Fax: [phone]