TDS

ManualsBrandsKILZ 2 ManualsPaint1-gal. White Water-Based Latex Interior/Exterior Multi-Surface Primer, Sealer and Stain-Blocker

Revised 6/2014

TECHNICAL DATA SHEET

This information is provided “as is” and no representations or warranties, either expressed or implied, of merchantability, tness for a particular purpose or of any other

nature are made with respect to this information or to any product referred to in this information. For MSDS or to consult with a technical service representative, call

Revised 11/2015

1 of 1

INTERIOR / EXTERIOR WATER-BASE PRIMER

NO. 2000

PRODUCT INFORMATION

KILZ 2® Latex Interior/Exterior Water-Based Primer is a fast drying, water-based multi-purpose primer, sealer and

stainblocker that has a very mild odor and blocks out most light stains including water, rust, grease, ink, pencil and felt

marker. For use on interior and exterior surfaces. Not recommended on ooring.

RECOMMENDED USES:

This product is ideal over oil or water-based coatings, stains and glossy surfaces. Use on properly prepared interior and

exterior surfaces such as:

• Concrete • Concrete Block/CMU • Cement Board Siding • Brick

• Stucco • Paneling • Plaster • Drywall/Gypsum Board

• Wood • Plywood • Non-Ferrous Metals • Architectural Plastics

PRODUCT SPECIFICATIONS:

Tint Bases/Max Tint Load:

No. 2000 128 oz. / 2 oz.

Resin Type: Acrylic Polymer

Weight per Gallon: 10.8 lbs.

% Solids by Volume: 34.0%

% Solids by Weight: 48.5%

VOC: <50 g/L

Flash Point: N/A

Viscosity: 95 - 105 KU

Recommended Film Thickness:

Wet: 5.3 mils / Dry: 1.8 mils @ 300 Sq. Ft./Gal.

Wet: 4.0 mils / Dry: 1.4 mils @ 400 Sq. Ft./Gal.

Coverage: 300 - 400 Sq. Ft./Gal. depending on the surface

texture, porosity and application method. Does not include

the loss of material from spraying.

APPLICATION:

Brush: Nylon / Polyester

Roller: 3/8" - 3/4" nap

Airless Spray: Fluid pressure of 2,500 - 3,200 psi

Tip: .015" - .021"

Filter: 60 mesh

Thinning: Not recommended. Product is formulated for use

at package consistency only.

Dry Time: @ 77°F, 50% RH

Longer dry time required in cooler temperatures and in

higher humidity.

To Touch: 30 minutes

To Recoat: 1 hour

SURFACE PREPARATION:

The surface must be clean, free of dust, grease, wax, peeling

paint, mold, mildew and wallpaper paste. If washing is

necessary, use a non-soapy detergent or a TSP substitute.

Rinse well and allow to dry.

Peeling or Checked Paint: Scrape o loose paint and sand

to a smooth surface. Sanding or removal of paint containing

lead is hazardous.

Unpainted, exterior wood: Exposed to sun and/or

moisture longer than 2-4 weeks must be cleaned and

sanded before priming.

Glossy Surfaces: For maximum adhesion, scu sand the

surface thoroughly before priming.

Masonry, Brick, Stucco and Plaster: KILZ 2 Latex

Interior & Exterior Water-Base Primer may be used on clean,

dry, aged masonry surfaces. New masonry must be allowed

to cure (dry) at least 30 days before applying

KILZ 2 Latex Primer.

Fire Restoration: It is critical to clean smoke damaged

surfaces thoroughly before priming.

Primary Recommendations: Use a product such as

KILZ MAX®, KILZ COMPLETE®, KILZ ODORLESS® or

KILZ® ORIGINAL Primers.

WARNING! If you scrape, sand or remove old paint, you

may release lead dust. LEAD IS TOXIC. Contact the National

Lead Information Center at 1-800-424-LEAD or visit

www.epa.gov/lead.

TEST SPECIFICATIONS:

Flexibility

ASTM D522 - Pass

Biological Growth

ASTM D3274 - Pass

CLEAN UP:

Clean all tools and equipment with clean water. For disposal

of empty containers and unused product, contact your

household refuse collection service.

CAUTIONS/LIMITATIONS:

• Protect from freezing.

• For best results, apply at temperatures between

50°F - 90°F. Temperatures above 90°F may aect the

application such as drying too fast. Avoid painting in

direct sun.

• Shelf life under normal conditions is two years unopened.

• Partially used cans might develop skinning if not

tightly sealed.

GENERAL INFORMATION:

Warning! Causes eye and skin irritation. Wear protective

clothing, gloves, eye, and face protection. Do not eat, drink,

or smoke when using this product. Take o contaminated

clothing and wash it before reuse. Wash hands thoroughly

after handling. Dispose of unused contents, container and

other contaminated wastes in accordance with local, state,

federal and provincial regulations.

First aid: If in eyes: Rinse cautiously with water for several

minutes and remove contacts if present and easy to do.

Continue rinsing and get medical attention if eye irritation

persists. If on skin: Wash with plenty of soap and water.

If swallowed: Rinse mouth and get medical attention if

you feel unwell.

COMPLIES WITH THE BELOW AS OF 2/1/2015

SCAQMD YES LEED v.3 (2009)

†

YES

CARB YES LEED v.4

†

YES

OTC YES MPI# 6,17,39,50

LADCO YES GREENGUARD® YES

AIM YES CHPS YES

NAHB/ICC NGBS YES

†

Please visit www.usgbc.org/LEED for additional details.

GREENGUARD is a registered trademark of UL Company.

Summary of content (1 pages)

PAGE 1
TECHNIC AL DATA SHEET INTERIOR / EXTERIOR WATER-BASE PRIMER N O. 2000 PRODUCT INFORMATION COMPLIES WITH THE BELOW AS OF 2/1/2015 KILZ 2® Latex Interior/Exterior Water-Based Primer is a fast drying, water-based multi-purpose primer, sealer and stainblocker that has a very mild odor and blocks out most light stains including water, rust, grease, ink, pencil and felt marker. For use on interior and exterior surfaces. Not recommended on flooring. SCAQMD YES LEED v.3 (2009)† CARB YES LEED v.