TDS

TECHNICAL DATA SHEET
This information is provided “as is” and no representations or warranties, either expressed or implied, of merchantability, tness for a particular purpose or of any other
nature are made with respect to this information or to any product referred to in this information. For MSDS or to consult with a technical service representative, call
1-877-KILZ-PRO. ©2015 Masterchem Industries, 3135 Old Hwy M, Imperial, MO 63052-2834.
Revised 1/2016
1 of 2
INTERIOR / EXTERIOR OIL-BASE PRIMER
NO. 1012
PRODUCT INFORMATION
KILZ COMPLETE Interior/Exterior Oil-Base Primer is ideal for blocking stains, priming, and sealing almost all interior and
exterior surfaces. It is especially eective at blocking grati, tannin, water, smoke and other bleeding stains. KILZ COMPLETE
Interior/Exterior Oil-Base Primer dries quickly and provides a mildew resistant coating. It can be used under latex or oil-based
paint. Not recommended on ooring.
RECOMMENDED USES:
Use on properly prepared interior and exterior cured surfaces such as:
• Concrete • Concrete Block/CMU • Cement Board Siding
• Brick • Stucco • Plaster
• Wood • Plywood • Ferrous Metals
PRODUCT SPECIFICATIONS:
Tint Bases/Max Tint Load:
No. L1012 128 oz. / 2 oz.
No. L1013 128 oz. / 2 oz.
No. L1012 (350 VOC)
Resin Type: Alkyd
Weight per Gallon: 11.3 lbs.
% Solids by Volume: 54.4%
% Solids by Weight: 74.6%
Flash Point: 74°F
Viscosity: 80 - 90 KU
No. L1013 (450 VOC)
Resin Type: Alkyd
Weight per Gallon: 10.3 lbs.
% Solids by Volume: 42.3%
% Solids by Weight: 64.3%
Flash Point: 71°F
Viscosity: 85 - 95 KU
Recommended Film Thickness:
Wet: 5.3 mils / Dry: 3.0 mils @ 300 Sq. Ft./Gal.
Wet: 4.0 mils / Dry: 2.2 mils @ 400 Sq. Ft./Gal.
Coverage: 300 - 400 Sq. Ft./Gal. depending on the surface
texture, porosity and application method. Does not include
the loss of material from spraying.
APPLICATION:
Brush: Nylon / Polyester Blend
Roller: 3/8" - 1/2" nap
Airless Spray: Fluid pressure of 2,500 - 3,200 psi
Tip: .015" - .021"
Filter: 60 mesh
Thinning: Not recommended. Product is formulated for use
at package consistency only.
Dry Time: @ 77°F (25°C), 50% RH
Longer dry time required in cooler temperatures and in
higher humidity.
350 VOC
To Touch: 90 minutes
To Recoat: 2 hours
450 VOC
To Touch: 90 minutes
To Recoat: 2 hours
SURFACE PREPARATION:
The surface must be clean, free of dust, grease, wax, peeling
paint, mold, mildew and wallpaper paste. If washing is
necessary, use a non-soapy detergent or a TSP substitute.
Rinse well and allow to dry.
Peeling or Checked Paint: Scrape o loose paint and sand
to a smooth surface. Sanding or removal of paint containing
lead is hazardous.
Unpainted, Exterior Wood: If exposed to sun and/or
moisture longer than 2 - 4 weeks must be cleaned and
sanded before priming.
Glossy Surfaces: For maximum adhesion, scu sand the
surface thoroughly before priming.
Masonry, Brick, Stucco and Plaster: KILZ COMPLETE
Interior/Exterior Oil-Base Primer may be used on clean, dry,
aged masonry surfaces that have cured (dried) at least 90 days.
If masonry has been cured less than 90 days, use a product such
as KILZ® PREMIUM Interior/Exterior Water-Base Primer.
Fire Restoration: It is critical to clean smoke damaged
surfaces thoroughly before priming.
WARNING! If you scrape, sand or remove old paint,
you may release lead dust. LEAD IS TOXIC. Contact the
National Lead Information Center at 1-800-424-LEAD or
visit www.epa.gov/lead.
TEST SPECIFICATIONS:
Flexibility
ASTM D522 - Pass
Adhesion Cured Enamels
ASTM D3359, >4B
Biological Growth
ASTM D3274 - Pass
CLEAN UP:
Clean all tools and equipment with mineral spirits.
For disposal of empty containers and unused product,
contact your household refuse collection service.
CAUTIONS/LIMITATIONS:
• IMPORTANT! Do not open can without reading instructions.
• Do not use when air and surface temperatures are below
50°F or above 90°F.
• Shelf life under normal conditions is two years unopened.
GENERAL INFORMATION:
Danger: Flammable liquid and vaper. May be fatal if
swallowed and enters airways. Causes serious eye and skin
irritation. Harmful if inhaled. May cause drowsiness or
dizziness. DO NOT use this product unless you can achieve
cross-ventilation by opening windows and doors during
application and drying or use the product outdoors. Do not
spray on an open ame or other ignition source. Extinguish
all ames and pilot lights and turn o stoves, heaters,
electric motors, high intensity lights and other sources of
ignition during use and until all vapors are gone. In case
of re: Use dry chemical, carbon dioxide to extinguish
small res. Wear protective clothing, gloves, eye and face
protection. Do not breathe vapors or spray mist. Do not
eat, drink or smoke when using this product. Wash hands
thoroughly after handling. Take o contaminated clothing
COMPLIES WITH THE BELOW AS OF 1/1/2016
SCAQMD YES LADCO YES
CARB YES AIM YES
OTC YES MPI# 5, 45, 76, 95, 136