TDS
TECHNICAL DATA SHEET
This information is provided “as is” and no representations or warranties, either expressed or implied, of merchantability, tness for a particular purpose or of any other
nature are made with respect to this information or to any product referred to in this information. For MSDS or to consult with a technical service representative, call
1-877-KILZ-PRO. ©2015 Masterchem Industries, 3135 Old Hwy M, Imperial, MO 63052-2834.
Revised 11/2015
PRODUCT INFORMATION
KILZ KLEAR® Interior/Exterior Water-Base Primer is a high performance fast-dry multi-surface clear primer developed to seal
porous surfaces inside and outside your home. Particularly eective for ‘same color painting’, KILZ KLEAR Interior/Exterior
Water-Base Primer will bond and seal porous and chalky surfaces with little change to current color. KILZ KLEAR Interior/Exterior
Water-Base Primer is a tough, exible and breathable lm to oer years of service. KILZ KLEAR Interior/Exterior Water-Base Primer
may also be used to seal highly porous surfaces with a transparent at nish. Suitable for sealing torn drywall facing paper, dried
wallcovering adhesive, ‘hot’ joint compounds, concrete and stucco with surface pH up to 12.5. Not recommended for oors.
RECOMMENDED USES:
Use on properly prepared interior and exterior surfaces, including:
• Concrete/Tilt-Up • Concrete Block/CMU • Cement Board Siding • Brick • Stucco
• Plaster • Drywall/Gypsum Board • Wood • Plywood • Ferrous Metal
• Non-Ferrous Metal • Architectural Plastics • Vinyl/PVC • Fiberglass
PRODUCT SPECIFICATIONS:
Tint Bases/Max Tint Load:
No. 2201 128 oz. / 2 oz.
Resin Type: Styrene Acrylic
Weight per Gallon: 8.6 lbs.
% Solids by Volume: 17.5%
% Solids by Weight: 19.7%
VOC: < 100 g/L
Flash Point: N/A
Viscosity: 60 - 70 KU
Recommended Film Thickness:
Wet: 5.4 mils / Dry: 1.0 mils @ 300 Sq. Ft./Gal.
Wet: 4.0 mils / Dry: 0.7 mils @ 400 Sq. Ft./Gal.
Coverage: 300 - 400 Sq. Ft./Gal. depending on the surface
texture, porosity and application method. Does not include
the loss of material from spraying.
APPLICATION:
Brush: Nylon / Polyester
Roller: 3/8" - 1/2" nap
Airless Spray: Fluid pressure of 2,500-3,200 psi
Tip: .015" - .017"
Filter: 60 mesh
Thinning: Not recommended. Product is formulated for use
at package consistency only.
Dry Time: @ 77°F, 50% RH
Longer dry time required in cooler temperatures and in
higher humidity.
To Touch: 30 minutes
To Recoat: 1 hour
SURFACE PREPARATION:
All surfaces must be clean, free of dust, chalk, oil, grease,
wax polish, mold and mildew, loose peeling paint, rust and
all other foreign substances.
Wash: If washing is necessary, use a non-soapy detergent or
TSP substitute. Rinse well and allow to dry.
Peeling or Checked Paint: Scrape o loose paint and sand
to a smooth surface. Sanding or removal of paint containing
lead is hazardous.
Glossy Surfaces: Scu and sand to de-gloss and wipe clean
before application.
WARNING! If you scrape, sand or remove old paint, you
may release lead dust. LEAD IS TOXIC. Contact the National
Lead Information Center at 1-800-424-LEAD or visit
www.epa.gov/lead.
CLEAN UP:
Clean all tools and equipment with clean water. For disposal
of empty containers and unused product, contact your
household refuse collection service.
CAUTIONS/LIMITATIONS:
• IMPORTANT! Do not open can without reading instructions.
• Do not use on oors.
• Do not use when air and surface temperatures are below
50° or above 90°.
• Shelf life under normal conditions is two years unopened.
GENERAL INFORMATION:
Warning! Causes eye and skin irritation. Harmful if swallowed.
Wear protective clothing, gloves, eye, and face protection.
Do not eat, drink, or smoke when using this product. Take o
contaminated clothing and wash it before reuse. Wash hands
thoroughly after handling. Collect spillage and avoid release to
the environment. Dispose of unused contents, container and
other contaminated wastes in accordance with local, state,
federal and provincial regulations.
First aid: If in eyes: Rinse cautiously with water for several
minutes and remove contacts if present and easy to do.
Continue rinsing and get medical attention if eye irritation
persists. If on skin: Wash with plenty of soap and water.
If swallowed: Rinse mouth and get medical attention
if you feel unwell.
1 of 1
INTERIOR/EXTERIOR WATER-BASE PRIMER
NO. 2201
COMPLIES WITH THE BELOW AS OF 9/1/2014
SCAQMD YES LADCO YES
CARB YES AIM YES
OTC YES LEED v.3 (2009
†
) YES
GREENGUARD® YES LEED v.4
†
YES
CHPS YES
†
Please visit www.usgbc.org/LEED for additional details.
GREENGUARD is a registered trademark of UL Company.