TDS
TECHNICAL DATA SHEET
This information is provided “as is” and no representations or warranties, either expressed or implied, of merchantability, tness for a particular purpose or of any other
nature are made with respect to this information or to any product referred to in this information. For MSDS or to consult with a technical service representative, call
1-877-KILZ-PRO. ©2014 Masterchem Industries, 3135 Old Hwy M, Imperial, MO 63052-2834.
Revised 11/2015
1 of 2
INTERIOR OIL-BASED PRIMER
NO. 1004
PRODUCT INFORMATION
KILZ ODORLESS Oil-Base Primer is a powerful interior stain blocker with no lingering odor. Ideal for use in oces, schools,
dining areas, apartments and other areas where high odor levels are prohibitive. Use KILZ ODORLESS Primer to block stains
including water, tannin and smoke from tobacco and re. Not recommended for oors.
RECOMMENDED USES:
Use on properly prepared interior surfaces, such as:
• Drywall/Gypsum Board • Wood • Plaster
• Concrete • Concrete Block/CMU • Non-Ferrous Metals
• Brick • Paneling
PRODUCT SPECIFICATIONS:
Tint Bases/Max Tint Load:
No. 1004 128 oz. / 2oz.
Resin Type: Solution Acrylic
Weight per Gallon: 13.2 lbs.
% Solids by Volume: 53.3%
% Solids by Weight: 7 7. 9 %
VOC: 350 g/L
Flash Point: 102°F (38.9°C)
Viscosity: 85 - 95 KU
Recommended Film Thickness:
Wet: 5.3 mils / Dry: 3.0 mils @ 300 Sq. Ft./Gal.
Wet: 4.0mils / Dry: 2.1 mils @ 400 Sq. Ft./Gal.
Coverage: 300 - 400 Sq. Ft./Gal. depending on the surface
texture, porosity and application method. Does not include
the loss of material from spraying.
APPLICATION:
Brush: Nylon / Polyester Blend or Premium Natural Bristle
Roller: 3/8" - 1/2" nap
Airless Spray: Fluid pressure of 2,500 - 3,200 psi
Tip: .015" - .021"
Filter: 60 mesh
Thinning: Not recommended. Product is formulated for use
at package consistency only.
Dry Time: @ 77°F, 50% RH
Longer dry time required in cooler temperatures and in
higher humidity.
To Touch: 30 minutes
To Recoat: 1 hour
Stainblocking: After priming, test for stain bleed-through
by applying the topcoat to a small section. If the stain bleeds
through the topcoat, apply a second coat of primer and
test again before topcoating the entire area. If bleeding
continues, a longer dry time is needed before topcoating.
KILZ ODORLESS Primer may be tinted with up to 2 ounces of
universal colorant per gallon for non-stainblocking projects.
Tinting to a lighter shade than the topcoat is recommended.
SURFACE PREPARATION:
The surface must be clean, free of dust, grease, wax, peeling
paint, mold, mildew and wallpaper paste. If washing is
necessary, use a non-soapy detergent or a TSP substitute.
Rinse well and allow to dry.
Peeling or Checked Paint: Scrape o loose paint and sand
to a smooth surface. Sanding or removal of paint containing
lead is hazardous.
Glossy Surfaces: For maximum adhesion, scu sand the
surface thoroughly before priming.
Note: Products such as KILZ® PREMIUM and KILZ 2® Primers
are recommended for mildew-prone surfaces.
Masonry, Brick, Stucco and Plaster: KILZ ODORLESS
Interior Oil-Base Primer may be used on clean, dry, aged
masonry surfaces. New masonry must be allowed to cure
(dry) at least 30 days before applying KILZ ODORLESS
Interior Oil-Base Primer.
Fire Restoration: It is critical to clean smoke damaged
surfaces thoroughly before priming.
WARNING! If you scrape, sand or remove old paint, you
may release lead dust. LEAD IS TOXIC. Contact the National
Lead Information Center at 1-800-424-LEAD or visit
www.epa.gov/lead.
CLEAN UP:
Clean all tools and equipment with mineral spirit. For
disposal of empty containers and unused product, contact
your household refuse collection service.
CAUTIONS/LIMITATIONS:
• Protect from freezing.
• For best results, apply at temperatures between 45°F -
90°F. Temperatures above 90°F may aect the application
such as drying too fast. Avoid painting in direct sun.
• Shelf life under normal conditions is two years unopened.
• Partially used cans might develop skinning if not
tightly sealed.
GENERAL INFORMATION:
Danger: Flammable liquid and vapor. May be fatal if
swallowed and enters airways. Causes serious eye and skin
irritation. Harmful if inhaled. May cause drowsiness or
dizziness. DO NOT use this product unless you can achieve
cross-ventilation by opening windows and doors during
application and drying or use the product outdoors. Do not
spray on an open ame or other ignition source. Extinguish
all ames and pilot lights and turn o stoves, heaters,
electric motors, high intensity lights and other sources of
ignition during use and until all vapors are gone. In case
of re: Use dry chemical, carbon dioxide to extinguish
small res. Wear protective clothing, gloves, eye and face
protection. Do not breathe vapors or spray mist. Do not
eat, drink or smoke when using this product. Wash hands
thoroughly after handling. Take o contaminated clothing
and wash it before reuse. Keep container tightly closed.
Store locked up in a cool, well-ventilated place. Dispose of
unused contents, container, and other contaminated
wastes in accordance with local, state, federal, and
provincial regulations.
COMPLIES WITH THE BELOW AS OF 9/1/2014
AIM YES MPI# 45, 223
®