TDS

TECHNICAL DATA SHEET
This information is provided “as is” and no representations or warranties, either expressed or implied, of merchantability, tness for a particular purpose or of any other
nature are made with respect to this information or to any product referred to in this information. For SDS or to consult with a technical service representative, call
1-877-KILZ-PRO. ©2019 Masterchem Industries LLC, 3135 Old Hwy M, Imperial, MO 63052-2834.
Revised 03/2019
LOW ODOR STAIN BLOCKING PRIMER IN AN AEROSOL
NO. 1044
1 of 2
PRODUCT INFORMATION
KILZ® ORIGINAL LOW ODOR is an oil-based sealer, adhesion promoter and stain blocker with less odor than typical oil-based primers.
It also features fast odor dissipation technology which means no lingering odor. Ideal for use in oces, schools, dining areas,
apartments and other areas which are sensitive to solvent odors or high odor levels. Use KILZ ORIGINAL LOW ODOR to block stains
including water, tannin and smoke from tobacco and re. Not recommended for oors.
RECOMMENDED USES:
Use on properly prepared interior surfaces, such as:
• Wood • Brick • Wallpaper
• Drywall • Masonry • Painted Metal
• Plaster • Interior Paneling • Properly Prepared Glossy Surfaces
†
PRODUCT SPECIFICATIONS:
FILL
No. 14444 Aerosol – 13 oz (6 pack)
No. 10444 Aerosol – 13 oz (12 pack)
FINISH
85° = < 10.0
Sheen levels depend on porosity and various surface
irregularities.
COMPOSITION
Vehicle: Solution Acrylic
Weight Solids: 42%
Volume Solids: 17%
Max VOC (by weight): 60%
Max Product Weighted MIR: 0.7
Flash Point: -156°F (-104°C)
Coverage: 20 - 25 sq. ft. (1.9 - 2.3 m
2
) per container,
depending on the surface texture, porosity and application
method. Does not include the loss of material from spraying.
APPLICATION:
• Eye protection is recommended.
• For best results, use at room temperature.
• Cover adjacent areas to protect from overspray.
• Shake can vigorously for 1 minute after mixing ball begins
to rattle and often during use.
• Hold can upright, moving from side-to-side while spraying
lightly and evenly about 12" from area being painted.
• 2-3 thin coats produce best results.
• Topcoat with latex or oil-based paint after 60 minutes.
• NOTE: On some surfaces, spot priming may cause a
non-uniform appearance in the nal coat. To avoid this,
prime the entire surface.
Dry Time: @ 77°F (25°C), 50% RH
Longer dry time may be required in cooler temperatures and
in higher humidity.
To Touch: 15-30 minutes
To Recoat: 1 Hour
SURFACE PREPARATION:
The surface must be clean, free of dust, grease, wax, peeling
paint, mold, mildew and wallpaper paste. If washing is
necessary, use a non-soapy detergent or a TSP substitute.
Rinse well and allow to dry.
Peeling or Checked Paint: Scrape o loose paint and
sand to a smooth surface. Sanding or removal of paint
containing lead is hazardous.
*
†
Glossy Surfaces: For maximum adhesion, scu sand the
surface thoroughly before priming.
*
CLEAN UP:
• Clear spray valve immediately after use by turning can
upside down and spraying until only clear gas is released.
• If spray nozzle becomes clogged, remove and clean. Do not
stick pins or wire into can opening.
• Replace nozzle with valve opening pointed away from you.
• Clean fresh overspray with mineral spirits or paint thinner.
Remove dried paint with paint remover, but test small area
rst to ensure paint remover does not damage substrate.
• Please consider donating any unused product.
• For recycling or disposal information, contact your local
household refuse collection service.
CAUTIONS/LIMITATIONS:
LIFETIME LIMITED WARRANTY: Masterchem Industries
LLC warrants to you, the original residential consumer
purchaser, the performance of this product as described
on this label for so long as you reside in your home. If
this product is found to be defective upon inspection by
its representative, Masterchem Industries LLC will, at its
option and upon presentation of proof-of-purchase (the
original receipt), either furnish an equivalent amount of
new product or refund the original purchase price of this
product to you. This warranty is not transferable. This
warranty excludes (1) labor and costs of labor for
the application or removal of any product, and (2)
any incidental or consequential damages, whether
based on breach of express or implied warranty,
negligence, strict liability or any other legal theory.
Some states do not allow the exclusion or limitation
of incidental or consequential damages, so the above
limitation or exclusion may not apply to you. To the extent
permitted by applicable law, any implied warranties
including the implied warranties of merchantability and of
tness for a particular purpose, are limited to the duration
of this express warranty. Some states do not allow
limitations on how long an implied warranty lasts, so
the above limitation may not apply to you. This warranty
gives you specic legal rights and you may also have other
rights, which vary from state to state. Note to residents
of the State of New Jersey: The provisions of this
warranty, including its limitations, are intended to
apply to the fullest extent permitted by the laws
of the State of New Jersey. For warranty service, call:
1-866-774-6371, or email: [e-mail].
Masterchem Industries LLC reserves the right to inspect
any and all application of the product prior to processing
your claim made under this warranty.
COMPLIES WITH THE BELOW AS OF 1/1/2019
SCAQMD YES LEED® NO
CARB YES MPI # 45, 46, 223
OTC YES MPI X-GREEN NO
LADCO YES GREENGUARD® NO
AIM YES GREEN SEAL™ NO
†
Please visit www.usgbc.org/LEED for additional details.