Use and Care Guide
TECHNICAL DATA SHEET
This information is provided “as is” and no representations or warranties, either expressed or implied, of merchantability, tness for a particular purpose or of any other
nature are made with respect to this information or to any product referred to in this information. For MSDS or to consult with a technical service representative, call
1-877-KILZ-PRO. ©2019 Masterchem Industries LLC, 3135 Old Hwy M, Imperial, MO 63052-2834.
Revised 02/2019
MOLD & MILDEW RESISTANT PRIMER FILM
NO. L2046
1 of 2
PRODUCT INFORMATION
KILZ® MOLD & MILDEW
†
Primer is a water based primer-sealer-stainblocker that is specially designed for residential surfaces
in high humidity, moisture and temperature environments such as kitchens, bathrooms, powder rooms and laundry rooms.
It oers excellent adhesion to both interior and exterior surfaces and provides a sound anchor for paints. The EPA registered
active ingredient creates a mold and mildew-resistant lm that protects the primer lm from mold and mildew growth.
KILZ MOLD & MILDEW Primer will block most medium to heavy stains including felt marker, grease, ink, pencil, tannin and water
stains. It is a fast drying, low odor, very low VOC formula and is easy to clean with soap and water. Not recommended for oors.
RECOMMENDED USES:
Use on properly prepared interior surfaces, such as :
• Drywall • Plaster • Paneling • Stucco
• Wood • Brick • Masonry • Painted Metal
• Residential Surfaces Prone to Moisture & Humidity (excludes insides of sinks, tubs, hot tubs, toilets, shower enclosures, pools,
and areas where direct water contact is regularly made)
PRODUCT SPECIFICATIONS:
Tint Bases/Max Tint Load:
No. L2046 128 oz. / 2 oz.
Resin Type: Acrylic Polymer
Weight per Gallon: 10.9 lbs.
% Solids by Volume: 41%
% Solids by Weight: 55%
VOC: <5 g/L
Flash Point: N/A
Viscosity: 95 - 101 KU
Recommended Film Thickness:
Wet: 5.3 mils / Dry: 2.2 mils @ 300 Sq. Ft./Gal.
Wet: 4.0 mils / Dry: 1.6 mils @ 400 Sq. Ft./Gal.
Coverage: 300 - 400 Sq. Ft./Gal. depending on the surface
texture, porosity and application method. Does not include
the loss of material from spraying.
APPLICATION:
Brush: Nylon / Polyester Blend
Roller: 3/8" - 3/4" nap
Airless Spray: Fluid pressure of 2,500 - 3,200 psi
Tip: .017"- .021"
Filter: 60 mesh
Thinning: Not recommended. Product is formulated for use
at package consistency only.
Dry Time: @ 77°F, 50% RH
Longer dry time required in cooler temperatures and in
higher humidity.
To Touch: 30 minutes
To Paint: 1 hour
SURFACE PREPARATION:
The surface to be primed must be clean, dry, free of dust,
chalk, oil, grease, wax, polish, mold and mildew, loose
or peeling paint, rust and all other foreign substances. If
washing is necessary, use a non-soapy detergent or a TSP
substitute. Rinse well and allow to dry.
Peeling or Checked Paint: Scrape o loose paint and sand
to a smooth surface. Sanding or removal of paint containing
lead is hazardous.
Glossy Surfaces: For maximum adhesion, scu sand the
surface thoroughly before priming.
Mold or Mildew Covered Surfaces: This product is
designed to prevent mold and/or mildew from forming and
contaminating the primer lm before topcoat is applied.
Although it is designed to be applied directly to mold and
mildew prone surfaces, any existing mold and/or mildew on
the surface should be removed before priming and painting.
This will ensure best results. Wash the area with a mildew
remover, rinse with water and allow to dry before priming.
Masonry, Brick, Stucco and Plaster: KILZ MOLD &
MILDEW Primer may be used on clean, dry, aged masonry
surfaces. New masonry must be allowed to cure (dry) at
least 30 days before applying KILZ MOLD & MILDEW Primer.
Fire Restoration: Not recommended. Primer
recommendations: KILZ® ORIGINAL and KILZ® ORIGINAL
EXTERIOR or KILZ® ORIGINAL LOW ODOR Primers for
oil based. KILZ® RESTORATION™ Primer for water based.
WARNING! If you scrape, sand or remove old paint, you
may release lead dust. LEAD IS TOXIC. Contact the National
Lead Information Center at 1-800-424-LEAD or visit
www.epa.gov/lead.
CLEAN UP:
Clean all tools, equipment and paint spatters with warm
clean water or warm soapy water.
SPILL CONTROL & DISPOSAL:
Do not dispose of this product down a drain. Please consider
donating any unused product. For recycling or disposal
information contact your local household refuse collection
service. If spilled, contain material and remove with an inert
absorbent. Dispose of contaminated absorbent, container and
unused product in accordance with all current federal, state
and local regulations. For recycling or disposal information,
contact your local household refuse collection service.
CAUTIONS/LIMITATIONS:
• Protect from freezing.
• For best results, apply at temperatures between 50°F -
90°F. Temperatures above 90°F may aect the application
such as drying too fast. Avoid painting in direct sun.
• Eye protection is recommended. Avoid contact with eyes.
• Avoid breathing of dust, vapors or spray mist. Open
windows and doors or use other means to ensure fresh air
entry during application and drying.
• Wear an appropriate, properly tted respirator (NIOSH /
MSHA TC 23C or equivalent) if vapor/mist levels cause eye
watering, headache or dizziness.
• Close container after each use.
• Wash hands thoroughly after handling and before smoking
and eating.
• Shelf life under normal conditions is two years unopened.
COMPLIES WITH THE BELOW AS OF 9/1/2014
SCAQMD YES AIM YES
CARB YES LEED v.3 (2009)
†
YES
OTC YES LEED v.4
†
YES
LADCO YES CHPS YES
TAV V
†
Please visit www.usgbc.org/LEED for additional details.
GREENGUARD is a registered trademark of UL Company.