Installation Guide

STEP-BY-STEP. . . CONT’D
C. Install Hinge-Side Z-Bar on the Door
1
2
3
4
Hold door on its edge hinge-side up.
Place Z-bar on the door edge (see diagram).
Position Z-bar so that it extends 3/16 of an inch
above the top of the door.
Center the hinges in the hinge groove and fasten
the Z-bar with the #8 1-1/4inch self-drilling zinc
screws supplied with the door.
Note: Use one screw per hinge for now. Screws and hinges will
center themselves in the door’s edge groove.
D. Place Door in Opening
1
2
3
4
5
6
7
Place the door in the opening so hinge-side Z-bar is even with the end of the drip cap and pushed tight
to the underside of the drip cap.
Pre-drill a 1/8 inch pilot hole into the brick mould through the top mounting hole in the Z-bar.
This helps prevent the brick mould from splitting.
Use one #8 1-1/4 inch white painted screw to secure the Z-bar to the brick mould.
Use a level to ensure Z-bar is vertical, then secure with the remaining #8 1-1/4inch white-painted screws.
Remember to pre-drill pilot holes with a 1/8inch drill bit to prevent splitting.
( distribute screws evenly with number of #8 1-1/4 inch white painted screws )
Open the door and check so that it swings freely and doesn’t bind.
With the door open, drill 1/8-inch pilot holes through the mounting holes on the inside edge of the Z-bar
just above and below the hinges.
Install the #8 1-inch zinc screws.
Note: If the door opening is at the upper limits of the size tolerances (see Determine Door Size), you
may need to place shims between the doorjamb and the Z-bar. After measuring for shim size
remove the door and secure the shims to the brick mould. Place the door back in position and
replace the #8 screw.
!
CAUTION
Do not over tighten the Z-bar. If it bends, back the screws out slightly until the
Z-bar springs back into position.
E. Level and Secure Drip Cap
1
2
3
Slightly loosen the screw holding the drip cap in position on the hinge side.
Adjust the drip cap until there is a uniform gap between the drip cap and the top edge of the door.
Drill pilot holes through the drip cap and secure to the doorframe with #8 1-1/4 inch white-painted screws.
F. Cut and Install the Latch-Side Z-Bar
1
2
3
4
5
6
Measure from bottom of drip cap to top of sill on the latch side. If your
doorsill is sloped you may cut the Z-bar to match this angle. Before cutting,
hold latch side of Z-bar in position to ensure that you trim any excess length
from the bottom of the Z-bar.
Use a hacksaw to cut the Z-bar to length.
Position the Z-bar on the latch side and allow a gap of 1/8 to 3/16 inch
between the door and the Z-bar.
Drill the top 1/8 inch pilot hole and screw in one #8 1-1/4 inch white-painted
screw.
Close the door to make sure the gap is uniform at the top and bottom then
pre-drill the remaining holes and secure using the white-painted screws.
Install the rest of the 1-1/4 inch self tapping screws in the hinges
-2-
Inside of Door
Z-Bar
5
There is an aluminum strip loosely installed on
the bottom of your door. Insert this strip into the
desired hinge side. *only in storm door models
Aluminum Support Bar
G. Install the Hardware
STEP-BY-STEP. . . CONT’D
!
CAUTION
See instructions in hardware kit.
H. Install the Pneumatic Door Closer
The pneumatic door closer must be positioned in the
centre of the rail below the door screen for structural
Measure to locate the centre of the rail. Ensure the
door closes and latches freely before installing the
closer.
Slide the hold open washer onto the closer rod.
Attach the closer to the door jam bracket using the
pin provided.
Extend the closer a ¼ inch using the hold open
bracket to lock it into place.
Mount the door bracket to the closer using the
pin provided.
Hold the bracket to the middle of the door and
pre-drill 2 pilot holes ¼ inch deep through the
door bracket.
1
2
3
4
5
6
7
(See diagram W1)
(See diagram H2)
(See diagram H3)
(See diagram H4)
Note: Do not drill completely through the front of the door.
-3-
Diagram H1:
Pneumatic Closer
Diagram H2:
Hold open washer
Diagram H3:
Pneumatic Closer
Diagram H4:
Pneumatic Closer
I. Install the Sweep
8
9
1
2
3
Insert screws to hold the bracket in place, then open the door
and slide the hold open washer back allowing the door to close.
Adjust the closer, if needed, to ensure the door latch engages properly.
Slide the door sweep over the door’s bottom edge. Align the sweep with the latch side and position so
rubber
ns touch the doorsill evenly along the bottom of the door.
Drill 3 pilot holes through spaced evenly in the door sweep using a 1/16 inch drill bit.
Secure the sweep using the three #8 ½ inch white-painted screws.
Take care not to drill through the front of the door.
(See diagram H5)
Note:
Diagram H5:
Bracket
CARE MAINTENANCEAND
Your new door requires minimal maintenance. Clean the door using mild soap and warm water. Avoid
using harsh abrasives. Do not touch up or try to repaint your vinyl door with any other type of paint.
LIMITED WARRANTY
Amherst Mouldings
We are so con dent in our product that we guarantee your door for 5 years from the date of purchase. If you
follow the recommendations outlined here you will enjoy your Amherst Mouldings door for many years to come.
Warranty will be void if you paint your vinyl door.
If an Amherst Mouldings Inc. Representative decides your door is defective, it will be replaced only with a door of the same
style and size. Amherst Mouldings Inc. is not responsible for the work required to hang, paint, or modify a replacement door.
We also reserve the right to substitute a door of a similar style, if necessary.
integrity.