Installation Guide

ManualsBrandsKINDRED ManualsDrop-in Kitchen Sinks20-Gauge Drop-In Stainless Steel 43.43 in. 4-Hole Corner Double Bowl Kitchen Sink

Congratulations!

You have purchased a quality product designed for long lasting beauty. The following instructions will take you step-

by-step through the installation process and care of your product. We recommend reading the entire instruction

booklet before beginning.

Caution: Risk of personal injury. Metal surfaces are sharp and can cause severe cuts. Use gloves and handle

sink and tools with care.

Installing Your New Sink

Tools And Materials

Step 1: Remove existing sink

1. Leave the faucet and drain outlet in place

2. Shut off water supply valves (usually under sink).

3. Release any water that may be in the supply lines by opening faucet valves

(the same way you would normally turn your water on). Let water run until it

stops owing.

4. Disconnect the supply lines from the water supply valves.

5. Disconnect the drain tting from the waste trap.

6. Remove clips around underside of old sink.

7. Lift sink out with faucet and drain tting still in place.

Topmount Installation Instructions:

Stainless Steel Sinks

KINDREDINST-TOP 01/15

1. Long Phillips head screwdriver

2. 2” hole saw (if installing new countertop)

3. Tube of silicone sealant or plumber’s putty

4. Adjustable wrench

5. Pipe wrench (if steel pipe is used)

6. Drill

7. Jigsaw

8. Gloves

9. Measuring tape

10. Work light

11. File

1. Phillips Screwdriver

3. Silicone Sealant or

Plumber’s Putty

2. Hole Saw

4. Adjustable

Wrench

9. Measuring

Tape

6. Drill

7. Jigsaw

5. Pipe Wrench

8. Gloves

10. Work Light

11. File

Supply valves

Waste trap

Supply

line

Step 1

Summary of content (6 pages)

PAGE 1
USA Topmount Installation Instructions: Stainless Steel Sinks Congratulations! You have purchased a quality product designed for long lasting beauty. The following instructions will take you stepby-step through the installation process and care of your product. We recommend reading the entire instruction booklet before beginning. Caution: Risk of personal injury. Metal surfaces are sharp and can cause severe cuts. Use gloves and handle sink and tools with care.
PAGE 2
OPTION B: Prepare a new countertop using the sink as a template 1. Carefully place the sink upside down on the countertop at the desired position. Trace the outline of the sink onto the countertop. Do not cut along this line. 2. Draw a line 3/8” (9mm) inside the sink outline. Measure the cut-out line you just drew and compare to all sink dimensions. The cut-out should be approximately 3/4” (19mm) smaller than the overall sink dimensions. 3. Verify both measurements. 4.
PAGE 3
7. Do not overtighten. It is only necessary to draw the rim down snugly to the countertop. 8. Wipe excess sealant from perimeter with a wet cloth. Step 6: Final Steps 1. Connect and tighten hot and cold faucet supply lines, strainer, drain and trap assembly. Note: Depending on the location of sink drain holes, it may be necessary to adjust the drain pipe fittings under the sink to accommodate the new sink installation. 2. Turn on water supply and examine all connections for leaks.
PAGE 4
USA Instrucciones de instalación del montaje superior: Fregaderos de acero inoxidable ¡Felicitaciones! Ha comprado un producto de calidad diseñado para brindar belleza duradera y muy fácil de instalar. Las instrucciones que aparecen a continuación le van a guiar paso a paso por el proceso de instalación y cuidado de su producto. Le sugerimos que lea todo el manual de instrucciones antes de seguir adelante. Precaución: Riesgo de lesiones personales.
PAGE 5
Paso 2: OPCIÓN A: Cómo preparar una encimera existente Paso 2 Largo Anc ho 1. Asegúrese de que el orificio existente en la encimera sea del tamaño adecuado. Coloque el fregadero nuevo dentro del orificio. El reborde del fregadero debe asentarse sin inconvenientes sobre la encimera. Para realizar ajustes leves, puede utilizar una lima o sierra de vaivén. 2. Utilice la lima o la sierra de vaivén con cuidado para no fragmentar ni quebrar la encimera. 3.
PAGE 6
. Por debajo de la encimera, comience a ajustar los sujetadores con un destornillador de forma uniforme y alternada hasta que el reborde quede sellado por completo. 7. No ajuste excesivamente. Basta con asentar el reborde firmemente sobre la encimera. 8. Limpie el exceso de sellador en el perímetro con un paño húmedo. Paso 6: Pasos finales 1. Conecte y ajuste los conductos de suministro de agua fría y caliente del grifo, el filtro, el drenaje y el ensamble del bote sifónico.