Instructions / Assembly

ManualsBrandsKing Arthur's Tools ManualsPower Tool AccessoriesRoyal Knight's Choice -2218 RMR Power Carving Kit

TANDEM MOUNTING - One Lancelot

With M14 (14mm) or 5/8”(16mm)

Center and One Lancelot

or Squire

with 7/8” (22mm) Center

1. DO NOT ATTEMPT TO TANDEM MOUNT A 7/8” (22mm) LANCELOT

ON THE BOTTOM

OF THREADED SHAFT WITH AN M14(14mm) OR A 5/8” (16mm) LANCELOT

SQUIRE ON TOP.

2. REMOVE THE GRINDER BACKING PLATE.

3. TIGHTEN WITH MANUFACTURER’S LOCK NUT.

These instructions are generally the same as tandem mounting a dual combination with M14

(14mm) or 5/8”(16mm) centers with the following important exceptions. After removing the

grinder backing plate, first mount one Lancelot

(NOT Squire

) with a M14 (14mm) or 5/8”

(16mm) center over the threaded shaft followed by the second Lancelot

or Squire

with a

7/8”(22mm) center. Any minor play prior to tightening the nut should be eliminated when this

combination is secured. You must use the manufacturer’s Flanged Lock Nut.

Insert the flange nut face down into the center hole of the top mounted Lancelot

or Squire

and tighten securely using manufacturer’s spanner wrenches. As a guide, the top of the nut

will be level or below the top of the threaded shaft when secured. There must be 1) no move-

ment or slippage of the saw chains between discs and 2) discs and chains must rotate as

one unit. SEE DIAGRAM 5.

Whichever tandem combination you ha

ve chosen, if you followed these instructions, you are

now ready to use one of the finest and most powerful cutting accessories in the world!

DIAGRAM 5

- 6 -

LANCELOT

& SQUIRE

GENERAL SETUP

Remove any non-KAT accessory

from the disc grinder.

Adjust the safety guard as shown

on WARNING - SAFETY GUARD

and assemble Lancelot

or Squire

as instructed in CHAIN AND

DISC ASSEMBLY.

CHAIN AND DISC ASSEMBLY - Lancelot

and Squire

1. Remove plastic center fastener. Retain for assembly when not attached to grinder.

2. Place BOTTOM disc on even surface, with the stamped word BOTTOM and directional

arrow facing up.

3. Place chain on BOTTOM disc with number 25 or 72

stamped on tang facing down. Ensure chain link tangs

fit over disc perimeter, with rakers facing left.

SEE DIAGRAM 2 - CHAIN DIRECTION. If assembled

in reverse, saw chain blades will not cut efficiently and

will appear blunt during operation by burning the wood.

4. Place TOP disc over chain circlet, with the decal and the

side stamped TOP side facing up. Minor adjustment will

secure chain between the two plates. SEE DIAGRAM 3 -

ASSEMBLY. Lancelot

or Squire

is ready for mounting to

disc grinder.

WARNING: DO NOT USE CUTTERS WITH INCOMPATIBLE GRINDERS

Do NOT Use Lancelot

or Squire

Saw Chain Blades, products of King Arthur’s Tools

on any 4” (100mm) angle grinder that requires safety guard modification by drilling an

additional hole in the body of the grinder. This includes any and all 4”(100mm) Makita

grinders that need the safety guard adjusted by drilling an additional hole in the body

of the grinder.

We do not support use of any 4” (100mm) angle grinders as described above.

e do, however, strongly support the use of 4-1/2” (115mm) angle grinders with

a constant pressure switch (paddle, kill or dead man switch). Safety is our utmost

iority and concern, however, under no circumstances will King Arthur’s Tools take

responsibility for any incident arising from improper use of our accessories or

ignorance of our recommendations and instructions.

DIAGRAM 2

Tang

Raker

DIAGRAM 2

CHAIN DIRECTION

- 3 -