Installation Guide

ManualsBrandsKing Canopy ManualsCar CanopiesUniversal 10 ft. x 20 ft. 6-Leg Canopy with Silver Cover

Universal

™

10ft X 20ft

10ft8in Wide x 20ft Deep x 5ft10in Side Height /

8ft11in Center Height

King Canopy Item #: C61020PC

With 6 Legs, White Drawstring Cover,

Elastic Ball Straps & Foot Pads.

WARNING:

Keep all ame and heat sources

away from this tent fabric. Meets

the ammability requirements of

CPAI-84 It is not re proof. The fabric

will burn if left in continuous contact

with any ame source.

Distributed by:

PIC America, LTD.

1730 Five Points Lane • Fuquay-Varina, NC 27526

1-800-800-6296 • www.kingcanopy.com

Summary of content (8 pages)

PAGE 1
Universal™ 10ft X 20ft 10ft8in Wide x 20ft Deep x 5ft10in Side Height / 8ft11in Center Height King Canopy Item #: C61020PC With 6 Legs, White Drawstring Cover, Elastic Ball Straps & Foot Pads. Distributed by: PIC America, LTD. 1730 Five Points Lane • Fuquay-Varina, NC 27526 1-800-800-6296 • www.kingcanopy.com WARNING: Keep all flame and heat sources away from this tent fabric. Meets the flammability requirements of CPAI-84 It is not fire proof.
PAGE 2
PARTS LIST 5X8PC 18 pc 68” Powder Coated Pipe 4X6PC 6 pc 52” Swaged Powder Coated Pipe 3WPC 6 pc 3-Way Connectors 4WPC 3 pc 4-Way Connectors BALL50W 50 pc Elastic Ball Straps PFOOT 6 pc Plastic Foot Pads TDS10206-5 1 pc White Drawstring Cover CCLIP 4 pc Curtain Clips
PAGE 3
FRAME ASSEMBLY Step 1 Place all corners and pipe on the ground as shown. The 52” swaged pipes are used to form the length of the canopy. Step 2 Start with the center and complete the center frame first. Then assemble each side. NOTE: Attach the cover before inserting the legs.
PAGE 4
COVER ASSEMBLY Step 1 Unfold the cover with the grommets toward the cover’s bottom and place over the frame. Step 2 Begin attaching the cover with the elastic ball straps by inserting the elastic cord of the ball strap underneath the cover and through the grommet. Then pull cord taut until ball stops. Wrap the cord around the pole and under the ball. This will hide the ball under the cover and provide a more finished look to your unit.
PAGE 5
LEGS ASSEMBLY NOW, CONNECT THE LEG POLES TO THE ROOF ASSEMBLY WITH THE COVER ALREADY POSITIONED ON TOP OF THE UNIT. Step A: First insert the pipes for the middle poles into the 3- and 4-way connectors, and then connect the end leg pipes in the same way. (See illustration) Step B: Slip one clip onto each of the corner legs. Step C: Push the foot pads onto the bottom of each leg.
PAGE 6
ANCHORING YOUR UNIT This canopy is designed for use as a temporary structure. After assembly, the canopy MUST BE securely anchored to the ground to prevent damage from winds. Your canopy will act like a kite in the wind if not properly and securely anchored to the ground. Severe winds will cause the frame to twist and unanchored legs will fall, thereby collapsing the canopy. If severe winds are expected, you must remove the cover from the frame to prevent damage.
PAGE 7
IMPORTANT NOTICE: PLEASE READ CAREFULLY We are confident that you will be completely satisfied with your King Canopy unit. Please take a moment to read the very important information below, and call us with any questions you may have. King Canopy/PIC America, LTD. has no control over wind, snow, ice, rain or any other weather condition and we are in no way responsible for any damage caused by the canopy or to the canopy.
PAGE 8
PRODUCT INFORMATION Defective Parts We try our best to eliminate any defective parts that are shipped with our products. If, however, you should find a defective part, we will replace – free of charge – any part which is defective. You will need to provide proof of purchase showing date of purchase and provide us with detailed description of the defective component. Your replacement will be shipped by ground shipping, freight prepaid.