Instructions / Assembly

ManualsBrandsKing Canopy ManualsOutdoors10 ft. W x 10 ft. D Greenhouse

Greenhouse 10ft X 10ft

9ft4in Wide x 10ft3in Deep x 5ft4in Side Height /

7ft10in Center Height

King Canopy Item #: GH1010

With 6 Legs, Cover,

Elastic Ball Straps & Foot Pads.

WARNING:

Keep all ame and heat sources

away from this tent fabric. Meets

the ammability requirements of

CPAI-84 Section 6 and NFPA-701.

It is not re proof. The fabric will burn if

left in continuous contact with

any ame source.

Distributed by:

PIC America, LTD.

1730 Five Points Lane • Fuquay-Varina, NC 27526

1-800-800-6296 • www.kingcanopy.com

These Tools Are

Recommended:

Summary of content (7 pages)

PAGE 1
Greenhouse 10ft X 10ft 9ft4in Wide x 10ft3in Deep x 5ft4in Side Height / 7ft10in Center Height King Canopy Item #: GH1010 With 6 Legs, Cover, Elastic Ball Straps & Foot Pads. These Tools Are Recommended: Distributed by: PIC America, LTD. 1730 Five Points Lane • Fuquay-Varina, NC 27526 1-800-800-6296 • www.kingcanopy.com WARNING: Keep all flame and heat sources away from this tent fabric. Meets the flammability requirements of CPAI-84 Section 6 and NFPA-701. It is not fire proof.
PAGE 2
PARTS LIST 5X0PCS 22 pc 60” powder coated pipe 3WPCS 6 pc 3-way connectors 4WPCS 3 pc 4-way connectors BALL50W 50 pc Elastic ball straps FOOTPCS 6 pc Metal foot pads GH1010T 1 pc One piece cover DC1313 2 pc Double pipe clamps w/bolts SC1313 4 pc Single pipe clamps w/bolts
PAGE 3
FRAME ASSEMBLY 1. Separate all pieces according to size and shape and arrange per the illustration shown below. All the pipes are 60” long. 60” 60” 60” 60” 60” 60” 60” 60” 60” There are six 60” pipes for the legs. 60” 60” 60” 2. Start with the center and complete the center frame first. Then assemble each side. 60’’ 60’’ Start Here 3. Cover installation - Before installing cover, unzip the door on the cover. This will make installation easy and will not cause damage to zippers.
PAGE 4
LEGS & COVER ASSEMBLY 1. Lift one side of canopy top and insert legs. Proceed to the other side. Insert second Insert first 2. Pull sides of tarp down and adjust until it fits equally on all sides. CANOPY REMOVAL: The best way to remove and fold the cover would be to follow the exact opposite of the installation process. Detach all the ball bungees, unzip the door, slide up the sides and fold them over onto the roof. Disassemble your structure by removing the legs from one side and lowering it.
PAGE 5
LEGS & COVER ASSEMBLY TO GET A TIGHTER FIT ON CANOPY COVER The ball straps are long enough to accommodate various cover lengths. If your straps are too long for a tight fit making an additional knot in the strap cord can shorten them. 1. 2. 3. 4. Slide the ball upwards to reveal the tied knot. Tie a new knot above the old one. The length taken up here determines how short the strap becomes. Slip the ball down over the new knot.
PAGE 6
IMPORTANT NOTICE: PLEASE READ CAREFULLY We are confident that you will be completely satisfied with your King Canopy unit. Please take a moment to read the very important information below, and call us with any questions you may have. King Canopy/PIC America, LTD. has no control over wind, snow, ice, rain or any other weather condition and we are in no way responsible for any damage caused by the canopy or to the canopy.
PAGE 7
PRODUCT INFORMATION Defective Parts We try our best to eliminate any defective parts that are shipped with our products. If, however, you should find a defective part, we will replace – free of charge – any part which is defective. You will need to provide proof of purchase showing date of purchase and provide us with detailed description of the defective component. Your replacement will be shipped by ground shipping, freight prepaid.