Replacement Part List

ManualsBrandsKing Canopy ManualsGarden CenterHercules 10 ft. x 20 ft. Canopy with Greenhouse Cover

Hercules

™

10ft X 20ft

10ft8in Wide x 20ft Deep x 6ft8in Side Height /

9ft9in Center Height

King Canopy Item #: HC1020PC

With 8 Legs, White Drawstring Cover,

Elastic Ball Straps & Plastic Foot Pads.

WARNING:

Keep all ame and heat sources

away from this tent fabric. Meets

the ammability requirements of

CPAI-84 It is not re proof. The fabric will

burn if left in continuous contact with

any ame source.

Distributed by:

PIC America, LTD.

1730 Five Points Lane • Fuquay-Varina, NC 27526

1-800-800-6296 • www.kingcanopy.com

Summary of content (8 pages)

PAGE 1
Hercules™ 10ft X 20ft 10ft8in Wide x 20ft Deep x 6ft8in Side Height / 9ft9in Center Height King Canopy Item #: HC1020PC With 8 Legs, White Drawstring Cover, Elastic Ball Straps & Plastic Foot Pads. Distributed by: PIC America, LTD. 1730 Five Points Lane • Fuquay-Varina, NC 27526 1-800-800-6296 • www.kingcanopy.com WARNING: Keep all flame and heat sources away from this tent fabric. Meets the flammability requirements of CPAI-84 It is not fire proof.
PAGE 2
PARTS LIST 6X6-2PC 17 pc 78” Powder Coated Pipe 5X8-2PC 8 pc 68” Powder Coated Pipe 3W2PC 6 pc 3-way connectors 4W2PC 6 pc 4-way connectors BALL50W 50 pc Elastic ball straps FOOT2PC 8 pc Foot pads TDS10206-5 1 pc White Drawstring Cover CCLIP2 4 pc Curtain Clips
PAGE 3
FRAME ASSEMBLY Step 1 Separate all pieces according to size and shape and arrange per the illustration shown below. Please note: • The 68” (8) pipes are used to form the roof rafters • The 78” pipes are used for the roof and for the legs 78’’ 78’’ 78’’ 78’’ 68’’ 68’’ 78’’ 68’’ 78’’ 68’’ 68’’ 78’’ 68’’ 78’’ 68’’ 78’’ Set aside eight 78” pipes with inserts to use for legs. 68’’ 78’’ Step 2 Start with the center and complete the center frame first. Then assemble each side.
PAGE 4
COVER ASSEMBLY Step 1 Unfold the cover with the grommets toward the cover’s bottom and place over the frame. The flared edges should be located at each of the 4 corners of the frame. Step 2 Begin attaching the cover with the elastic ball straps by inserting the elastic cord of the ball strap underneath the cover and through the grommet. Then pull cord taut until ball stops. Wrap the cord around the pole and under the ball.
PAGE 5
LEGS ASSEMBLY NOW, CONNECT THE LEG POLES TO THE ROOF ASSEMBLY WITH THE COVER ALREADY POSITIONED ON TOP OF THE UNIT. Insert Second Insert First Step A: First insert the pipes for the middle poles into the 3- and 4-way connectors, and then connect the end leg pipes in the same way. (See illustration) Step B: Push the eight foot pads onto the bottom of each leg. NOTE: the foot pads are NOT for anchoring the canopy! Step C: Connect the hook & loop fastening strips down the length of each leg.
PAGE 6
ANCHORING YOUR UNIT This canopy is designed for use as a temporary structure. After assembly, the canopy MUST BE securely anchored to the ground to prevent damage from winds. Your canopy will act like a kite in the wind if not properly and securely anchored to the ground. Severe winds will cause the frame to twist and unanchored legs will fall, thereby collapsing the canopy. If severe winds are expected, you must remove the cover from the frame to prevent damage.
PAGE 7
IMPORTANT NOTICE: PLEASE READ CAREFULLY We are confident that you will be completely satisfied with your King Canopy unit. Please take a moment to read the very important information below, and call us with any questions you may have. King Canopy/PIC America, LTD. has no control over wind, snow, ice, rain or any other weather condition and we are in no way responsible for any damage caused by the canopy or to the canopy.
PAGE 8
PRODUCT INFORMATION Defective Parts We try our best to eliminate any defective parts that are shipped with our products. If, however, you should find a defective part, we will replace – free of charge – any part which is defective. You will need to provide proof of purchase showing date of purchase and provide us with detailed description of the defective component. Your replacement will be shipped by ground shipping, freight prepaid.