KCV Series Installation Manual

ManualsBrandsKing Electric ManualsCeiling Heaters71 in. 240-Volt 840-Watt Cove Heater in White

It is extremely important to verify the electrical power supply is the same voltage as the heater being installed.

240 and 120 Volt heaters are not interchangeable. Powering a 240 Volt unit with 120 Volt supply wires will

reduce heater output by approximately 75%. Powering a 120 Volt unit with 240 Volt supply wires will destroy the

heater and voids all guarantee and warranties.

CAUTION: Turn off power source supplying heater before attempting

any installation, maintenance or repairs. Lock or tag circuit breaker/fuse

panel door. Failure to do so could result in serious electrical shock, burns

or possible death.

WARNINGS: To insure proper operation of this heater it should be a minimum

of 6 feet above the ﬂoor and no closer than 2½” below drywall ceiling

(6” vinyl or drop ceilings). Draperies should clear the front and the top of this

heater by 6”. Draperies hung below the heater should have a 2½” clearance.

Do not block the heater in any manner. Never paint the heater.

MAINTENANCE & WARRANTY

KCV SERIES

Cove

Heater

SAVE THESE INSTRUCTIONS

GENERAL INFORMATION

KING ELECTRICAL MFG. COMPANY • 9131 10TH AVENUE SOUTH • SEATTLE, WA 98108 • PH: 206.762.0400 • FAX: 206.763.7738 • www.king-electric.com

REV. 66447_11-23-20

Cove heaters are completely assembled and pre-wired. To prepare

the heater for installation, carefully check the voltage to be used is

the same as stated on the rating nameplate. Operating voltage can

not exceed 5% of nameplate voltage. Operating heater above listed

voltage ratings voids all gaurantees and warranties.

Following the guidlines herein listed will result in a maintenance-free heater. There are no moving parts or motors

to maintain. Periodic dusting of the front panel is all that is suggested.

The KCV Cove Heater carries a (2) warranty form date of installation. Please refer to the manufacturer’s warranty

statement for further information.

Diag. A

KING ELECTRICAL MFG. COMPANY • 9131 10TH AVENUE SOUTH • SEATTLE, WA 98108 • PH: 206.762.0400 • FAX: 206.763.7738 • www.king-electric.com

Summary of content (4 pages)

PAGE 1
KCV SERIES Cove Heater It is extremely important to verify the electrical power supply is the same voltage as the heater being installed. 240 and 120 Volt heaters are not interchangeable. Powering a 240 Volt unit with 120 Volt supply wires will reduce heater output by approximately 75%. Powering a 120 Volt unit with 240 Volt supply wires will destroy the heater and voids all guarantee and warranties. CAUTION: Turn off power source supplying heater before attempting any installation, maintenance or repairs.
PAGE 2
Fig. D LEFT GREEN GROUND WIRE RIGHT END OF WHITE OR WHITE/BLACK WIRE LEFT WHITE SUPPLY WIRE #$-%".. Following are some general guidelines: • Do not recess this cove heater. • Disconnect power at main panel. • Make certain all wiring is in accordance with all local codes and units are properly grounded. • Voltage rating of heater should be the same as supply load. • Do not install the heater on vinyl wall coverings. 2. Remove heater from carton.
PAGE 3
Fig. D LEFT GREEN GROUND WIRE RIGHT END OF WHITE OR WHITE/BLACK WIRE LEFT WHITE SUPPLY WIRE #$-%".. Following are some general guidelines: • Do not recess this cove heater. • Disconnect power at main panel. • Make certain all wiring is in accordance with all local codes and units are properly grounded. • Voltage rating of heater should be the same as supply load. • Do not install the heater on vinyl wall coverings. 2. Remove heater from carton.
PAGE 4
KCV SERIES Cove Heater It is extremely important to verify the electrical power supply is the same voltage as the heater being installed. 240 and 120 Volt heaters are not interchangeable. Powering a 240 Volt unit with 120 Volt supply wires will reduce heater output by approximately 75%. Powering a 120 Volt unit with 240 Volt supply wires will destroy the heater and voids all guarantee and warranties. CAUTION: Turn off power source supplying heater before attempting any installation, maintenance or repairs.