English Outdoor cookers Jet and combination Burners Assembly Instructions and use and care Manual MODEL/serial # __________ THE INSTRUCTION MANUAL CONTAINS IMPORTANT INFORMATION NECESSARY FOR THE PROPER ASSEMBLY AND SAFE USE OF THE APPLIANCE. READ AND FOLLOW ALL WARNINGS AND INSTRUCTIONS BEFORE ASSEMBLING AND USING THE APPLIANCE. FOLLOW ALL WARNINGS AND INSTRUCTIONS WHEN USING THE APPLIANCE. KEEP THIS MANUAL FOR FUTURE REFERENCE. Metal Fusion, Inc. 712 St. George Avenue.
danger for your safety If you smell gas: 1. Shut off gas to the appliance. 2. Extinguish any open flame. 3. If odor continues, keep away from the appliance and immediately call your Fire Department. FAILURE TO FOLLOW THESE INSTRUCTIONS COULD RESULT IN FIRE OR EXPLOSION WHICH COULD CAUSE PROPERTY DAMAGE, PERSONAL INJURY OR DEATH. danger 1. Never operate this appliance unattended. 2. Never operate this appliance within 10 feet (3.05m) of any structure, combustible material or other gas cylinder.
Read and Understand before using this product Throughout this manual the words appliance, cooker, fryer/boiler, burner and stove will be used interchangeably to refer to the King Kooker® Outdoor Cooker. 1) This is an ATTENDED appliance. Do NOT leave this appliance unattended while the burner is lit or while heating oil, grease, water or cooking food. Monitor the appliance when hot after use [oil, grease or water above 100°F (38°C)].
13) Introduction of water or ice from any source into the oil/grease may cause overflow and severe burns from hot oil and water splatter. When frying with oil/ grease, all food products MUST be completely thawed and towel dried before being immersed in the fryer. 14) Never drop food or accessories into hot cooking liquid. Lower food and accessories slowly into the cooking liquid in order to prevent splashing or overflow.
Read and understand all instructions before using your king kooker® product table of contents Warnings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-4 Table of Contents. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Metal Fusion, Inc. Limited One-Year Warranty What this warranty covers This warranty covers all components of this outdoor cooker to be free from defects in materials and workmanship, with the exceptions stated below. How long coverage lasts This warranty runs for one year from the date of purchase. Please keep your receipt with this manual for future reference. what is not covered This warranty does not cover the following: Incidental and Consequential Damages.
Owner’s Registration Dear Customer, Thank you for purchasing a King Kooker®! Please take a moment to fill out your registration form and return it to us. We are always happy to hear suggestions and comments from our customers about our products. Completion of this registration allows us to contact you if the need arises. Please keep your receipt with your instruction manual. It will be necessary as a proof of purchase for us to help you if there is a problem with your cooker.
TAPE HERE FOLD ________________________ ________________________ ________________________ Place Stamp Here Metal Fusion, Inc. 712 St.
section I Outdoor Cooker Assembly The use and care manual must be read and understood before using the appliance Throughout this manual the words appliance, cooker, fryer/boiler, burner and stove will be used interchangeably to refer to the King Kooker® Outdoor Cooker. TOOLS REQUIRED: TORQUE WRENCH or ADJUSTABLE WRENCH, LEAK TESTING SOLUTION 1. Before assembling, check that all cooker components are included in the shipping carton. Identify these cooker parts from the assembly drawing.
c90pk, c90pkb, c90h/spk and C90SSPK assembly INSTRUCTIONS a. Locate the three separate plates. Lay the plates on a flat surface as shown in Figure 1 below. If one of the plates has a cutout along the inner edge, this plate must be installed around the adjustable baffle’s extension when following the steps below. (Some units have been designed with larger center cutouts and the baffle extension cutout has been eliminated from the design. Some models may not include an adjustable baffle.) b.
94/90TKD ASSEMBLY INSTRUCTIONS Lighting Hole See below illustration for part identification. Also included - 6 bolts, 8 Lockwasher and 8 Nuts Windshroud Top Frame Figure 1 Jet Pipe Cylinder Collar Cylinder Heat Shield Bottom Frame Wheels, Axles, Lockwashers and Nuts Tank Ring 1. Place top frame of unit onto bottom frame of unit as per Figure 1 above. Make sure the lighting hole located on the windshroud on the top frame is installed facing away from the jet burner, to the outside of the cooker frame.
6. Locate the three separate heat plate pieces. Lay the plates on a flat surface as shown in Figure 3. Place the rounded inner edge of one plate against the vertical jet pipe located on the bottom frame. The bottom of the plate should be located above the the “bent” prongs when installed (3 “bent” prongs welded to side of jet pipe.) The plate will fit around the “bent” area of the prong using the cutouts provided on the plate. Repeat procedure with the second plate.
94/90TKD HOSE ASSEMBLY INSTRUCTIONS 1. Wrench tighten the 3/8” female flare swivel to the brass adapter. If assembling a hose to a cast burner, determine if your hose has a 3/8” female flare swivel end or a 1/8” male pipe thread end. If your cooker has a 3/8” female flare end, wrench tighten it to the pre-installed half union located on the cast burner. If it has a 1/8” male pipe thread end, tighten the hose fitting into the venturi with a torque wrench, up to a torque of 95 to 105 lb./in.
C180PKHD assembly INSTRUCTIONS a. Locate the three separate plates. Lay the plates on a flat surface as shown in Figure 1 below. b. Place the rounded inner edge of one plate against the vertical jet pipe in center of cooker. The plate will fit around the appliance leg using the cutouts provided on the plate. Repeat procedure with the second plate. Align the bolt holes of the first and second plate and attach with bolt, lock washer and nut. Repeat procedure with third plate. Tighten all bolts/nuts.
9090 assembly INSTRUCTIONS 1. Remove unit from box and remove all packing materials between cooker frame and aluminum pot. All packaging materials must be removed before operation of the appliance. 2. Make sure the spigot drain valve is in the OFF/CLOSED position as pictured below. VALVE IN OFF/CLOSED POSITION SPIGOT 9090 HOSE ASSEMBLY INSTRUCTIONS 1. Wrench tighten the 3/8” female flare swivel to the brass adapter. 2. The hose to burner (brass adapter) connection must be tightened and leak tested.
9090 adjustable lid support system instructions Your cooker includes an adjustable rod system that can be used to support the pot’s lid when opened. Food contents within the pot’s basket can be emptied onto the lid when supported by the support rod system and then distributed into food trays or containers. The rod system can be adjusted so that the lid when opened and resting on the lid support rod will either be in an “angled” or “straight” position.
ANGLED LID POSITION FIGURE 2 FIGURE 3 LOWER TAB “LOWER” BAR “CENTER” BAR LOWER TAB LOWER TAB To install the adjustable lid support system in the angled position, remove the rods from the clamps. Rotate the “lower” bar downward and the “center” bar upward. Place the “lower” bar onto lower set of tabs (2) which are attached to the cooker frame as shown in Figure 2 and Figure 3 above.
9090 - OPERATION OF SPIGOT POT READ AND UNDERSTAND ALL INSTRUCTION BEFORE USING THIS PRODUCT. ALWAYS ALLOW COOKING LIQUID AND VALVE TO COOL BEFORE OPERATING SPIGOT (BELOW 100°F (38°C)). COOKING LIQUID CAN REMAIN DANGEROUSLY HOT HOURS AFTER USE. ALWAYS USE A THERMOMETER TO CHECK TEMPERATURE OF THE COOKING LIQUID BEFORE OPERATING THE SPIGOT. OPERATING INSTRUCTIONS FOR SPIGOT POT : 1. Before adding cooking liquid, make sure valve is in the OFF/Closed position as pictured in Figure 1 below.
section II Use and care Throughout this manual the words appliance, cooker, fryer/boiler, burner and stove will be used interchangeably to refer to the King Kooker® Outdoor Cooker. Read and Understand before using this appliance Failure to follow these instructions and warnings could result in fire, explosion, burn hazard or carbon monoxide poisoning which could cause Property Damage, Personal Injury or Death. Thermometer Instructions and safety Precautions For Deep Frying with Outdoor Cookers 1.
LP gas cylinder information King Kooker® Outdoor Cookers are manufactured for use with 20lb. (9 kg) LP Gas Cylinders. Important information to remember about LP Gas cylinders include: 1. 2. Always read and follow the cylinder manufacturer’s instructions. Make sure that the gas cylinder is not overfilled. The maximum weight of a properly filled 20 lb. (9 kg) LP gas cylinder is approximately 38 lbs (17 kg). Never fill the cylinder beyond 80% full. 3.
PLACEMENT INSTRUCTIONS 1. Never operate this appliance within 10ft. (3.05m) of any structure, combustible material or other gas cylinder. Never operate this appliance within 25ft. (7.5m) of any flammable liquids or vapors 2. There must be no combustibles or roof overhead. 3. For models with a tank ring for cylinder retention, place the cylinder base inside the ring as per Figure 3. The prongs that extend from the cart handle should bracket the cylinder’s collar. For all other models keep 24 inches (.
90B, 90H/S, 90H/SPK, 90PK, 90PKB, 90SSPK, c90pk, c90pkb, c90h/spk and C90SSPk lighting and operating Instructions The Cooker must not be lit until the preceding placement instructions have been completely followed. 1. 2. 3. 4. 5. 6. If your Jet Burner has a baffle over the jet tube, turn it away from the jet tube. Make certain that the regulator control is turned to OFF by turning it counterclockwise until it reaches the stop.
C180PKHD LIGHTING AND OPERATING INSTRUCTIONS The Cooker must not be lit until the preceding placement instructions have been completely followed. 1. 2. 3. 4. Make certain that the regulator control is turned to OFF by turning it counterclockwise until it reaches the stop. Open cylinder control valve by turning it counterclockwise as per the diagram (Figure 2). Hold a multipurpose lighter as per Figure 4 or paperbook match as per Figure 3 over one of the jet pipes.
94/90TKD LIGHTING AND OPERATING INSTRUCTIONS The Cooker must not be lit until the preceding placement instructions have been completely followed. 1. Check that the casting is properly located as per the diagram and that the orifice is properly located in respect to the jet pipe. (Figure 1) Turn triangle handle toward ON (Counterclockwise) VIEW FROM TOP OF LARGE JET PIPE ORIFICE 2.
9090 LIGHTING AND OPERATING INSTRUCTIONS The Cooker must not be lit until the preceding placement instructions have been completely followed. Pot must be installed onto cooker frame and filled with water before lighting appliance. The lid support rod must be in straight or angled position before lighting appliance. 1. 2. 3. 4. Make certain that the regulator control is turned to OFF by turning it counterclockwise until it reaches the stop.
Turning off and storing the cooker after use 1. 2. 3. Never Move the cooker OR POT while in use or still hot [above 100°F(38°C)]. After each use turn OFF the King Kooker® at the regulator/manual valve(s) first, then at the gas cylinder valve. Check to make sure there is no flame and all valves are off. Do not leave the cooker until it has cooled completely. When removing food from the cooker wear protective mitts.
7. Cleaning of the appliance: Cooker and LP Hose/Regulator: If necessary, remove any oil or liquid which has spilled onto the unit during cooking with mild soapy water on a rag and towel dry. Do not immerse the burner unit or hose and regulator into water as this will cause rust. Aluminum or Stainless Steel Pots: Clean after each use according to the directions below. Cast Iron Cookware: Clean after each use according to the directions below.
section III Recipes from The King of Outdoor Cooking™ The following recipes are based on common food quantites and pot sizes used in outdoor cooking. Variations will occur dependent on food quantities and pot sizes being used. Adjust the recipes accordingly. SUGGESTED RECIPES for Models 90B, 90H/S, 90H/SPK, 90PK, 90PKB, 90SSPK, c90pk, c90pkb, c90h/spk, C90SSPk, C180PKHD and 94/90tkd Boiled Seafood! The King Kooker® Way! For a 60 to 100 quart pot, fill 1/2 full of water.
additional SUGGESTED RECIPES for Model 94/90TKD (Cast burner) The below recipes are intended to be used with the cast burner side of the 94/90TKD. If using the jet burner side of the 94/90TKD with a large pot, see boiling and steaming recipes located on page 28. Blackened Fish Heat a cast iron skillet for at least ten minutes on your King Kooker®. Allow the skillet to get almost white hot -- hot enough to see the “flame circle” in the center of the skillet. This recipe produces lots of smoke.
section IV Read and understand all instructions before using your king kooker® product Frequently Asked Questions and Answers 1. What is the problem if the cooker takes too long or will not heat oil or cooking ingredients to desired temperature? My cooker’s flame appearance is very weak. Answer: If the hose assembly has a Type 1 Connection (black/green knob), it is equipped with a flow limiting device.
NOTES 31
or go to www.kingkooker.com , King GrilleRDine®, King Kooker®, the King Kooker® logo, The King®, the KING OF OUTDOOR COOKING®, Mr. Outdoors®, and WATCHDOG OUTDOOR COOKER SERIES® are trademarks of Metal Fusion, Inc., 712 St. George Avenue, Jefferson, LA 70121 Rev.
