User Guide

1. Turn on TV.
2. Turn on power to KING Jack antenna.
3. Perform a channel scan per the digital TV or digital TV
converter box manufacturer’s instructions.
4. Rotate antenna 90 degrees. Scan again.
5. Rotate antenna 90 degrees. Scan again.
6. Rotate antenna 90 degrees. Scan again.
7. Reposition your KING antenna to where you received the most channels.
Choose one of those channels on your TV. Now monitor the signal strength
screen and ne tune the KING Jack until the highest signal strength is achieved.
Perform one nal scan and watch TV. Enjoy!
Page 4
The optional KING SureLock Digital TV Signal Finder allows you to
pinpoint the location of local DTV towers and eliminate the need for
multiple channel scans. Consult your local dealer or visit
www.kingconnect.com for additional information.
IMPORTANT! Do not power wash any part of the KING Jack antenna.
OPERATING INSTRUCTIONS: Scanning for Channels
LIMITED WARRANTY
Every new KING Jack HDTV Antenna is covered by the following one-year parts limited warranty from the date of original purchase:
• One-year parts warranty: The customer is not responsible for the cost of replacement parts if the original part is determined to be defective under the terms of the warranty. The customer is responsible for the cost
of replacement parts after one year.
Should any trouble develop during the warranty period, contact KING. You must contact KING before the warranty period expires. The customer must supply proof of purchase (such as a dated sales receipt) when
requesting warranty service. If customer cannot supply proof of purchase, warranty period shall start 30 days after date of manufacture. Only KING will perform warranty evaluations and repairs.
If it is determined that the unit needs to be returned to KING, customer must return COMPLETE product, freight prepaid, to: KING, 11200 Hampshire Avenue South, Bloomington, MN 55438-2453.
If inspection shows the trouble is caused by defective workmanship or material, KING will repair (or at its option, replace) without charge.
When returning product, KING will supply an RMA number (Return Merchandise Authorization). This number must be clearly written on the box. Failure to clearly write RMA number on box may result in delays in
processing claim. Along with product, customer should include in the box: his/her name, address, daytime phone number, proof of purchase and description of the problem.
This warranty does not cover installation and external wiring, or remanufactured units. This warranty is not transferable from the original owner. This warranty also does not apply where:
• The product has been abused, misused, improperly installed or improperly maintained.
• Repairs have been made or attempted by others that are not certied by KING to do such repairs.
• Repairs are required because of normal wear and tear.
• Alterations have been made to the product.
• The product or any associated component has been opened without authorization or disassembled to any degree.
• Damage has been caused by power washing.
• Supplied grease not used in the external coax connection as specied in the instructions.
• Circumstances beyond the control of KING cause the product to no longer operate correctly.
• Customer is not the original owner.
In no event shall KING be liable for any indirect, incidental, or consequential damages from the sale or use of the product. This disclaimer applies both during and after the term of the warranty.
KING disclaims liability for any implied warranties, including implied warranties of “merchantability” and “tness for a specic purpose,” after the one year term of this warranty.
This warranty gives you specic legal rights, and you may also have other rights, which vary from state to state. Some states do not allow the exclusion or limitation of incidental or consequential damages, so the above
limitation or exclusion may not apply to you. Some states do not allow limitations on how long an implied warranty lasts, so the above limitation may not apply to you.
© 2017 KING 22545 REV E
TROUBLESHOOTING
SYMPTOM POSSIBLE REASON COURSE OF ACTION
No TV reception. No power to antenna.
(Red LED on antenna head
is not lit.)
Antenna pointed in wrong
direction.
Make sure power supply is plugged into a known good 110-120 VAC source.
Check for 12 VDC at power supply output. If not present, replace power supply.
Check for 12 VDC at antenna port of power injector. If voltage is not present, replace power
injector.
If voltage is present, the coax to the antenna or the antenna is bad.
Temporarily run a known good coax from the injector to the antenna. If you now have power
(red LED lit), replace the coax. If you don’t, replace the antenna.
Perform a 4 quadrant search as shown in the operating instructions or use a
KING SureLock Signal Meter to locate TV towers.
KING SureLock™
Digital TV Signal Finder SL1000
(sold separately)
11200 Hampshire Avenue South, Bloomington, MN 55438
PH 952.922.6889 || FAX [phone] || kingconnect.com
NOTE: In stationary applications, you only need to scan for channels one time. In mobile applications, you will need to scan for
channels each time you change locations.
KING Jack and KING SureLock are trademarks, and KING is a
registered trademark of Electronic Controlled Systems, Inc.
NOTE: In steps 3-6, keep track of in which position
you receive the most channels.
Winegard is a registered trademark of Winegard Company.
KING Jack
™
and KING SureLock
™
are products of KING
®
and are not afliated with nor manufactured by Winegard
®
Company.