Datasheet

ManualsBrandsKINGBRIGHT ManualsLEDs & AccessoriesSMD LED PLCC2 Yellow 250 mcd 120 ° 20 mA 2 V

SPEC NO: DSAK1880 REV NO: V.3B DATE: DEC/03/2011 PAGE: 1 OF 6

APPROVED: WYNEC CHECKED: Allen Liu DRAWN: C.H.Han ERP: 1201005727

2.2x1.4mm SURFACE MOUNT LED LAMP

Part Number: KA-2214SYSK

Super Bright Yellow

Features

z 2.2mm x 1.4mm, 1.3mm high.

z Low power consumption.

z Available on tape and reel.

z Package : 2000pcs / reel.

z Moisture sensitivity level : level 3.

z RoHS compliant.

Description

The Super Bright Yellow device is made with AlGaInP (on

GaAs substrate) light emitting diode chip.

Package Dimensions

Notes:

1. All dimensions are in millimeters (inches).

2. Tolerance is ±0.2(0.008") unless otherwise noted.

3. The specifications, characteristics and technical data described in the datasheet are subject to change without prior notice.

4. The device has a single mounting surface. The device must be mounted according to the specifications.

Summary of content (6 pages)

PAGE 1
2.2x1.4mm SURFACE MOUNT LED LAMP Part Number: KA-2214SYSK Super Bright Yellow Features Description z 2.2mm x 1.4mm, 1.3mm high. The Super Bright Yellow device is made with AlGaInP (on z Low power consumption. GaAs substrate) light emitting diode chip. z Available on tape and reel. z Package : 2000pcs / reel. z Moisture sensitivity level : level 3. z RoHS compliant. Package Dimensions Notes: 1. All dimensions are in millimeters (inches). 2. Tolerance is ±0.2(0.008") unless otherwise noted. 3.
PAGE 2
Handling Precautions Compare to epoxy encapsulant that is hard and brittle, silicone is softer and flexible. Although its characteristic significantly reduces thermal stress, it is more susceptible to damage by external mechanical force. As a result, special handling precautions need to be observed during assembly using silicone encapsulated LED products. Failure to comply might lead to damage and premature failure of the LED. 1.
PAGE 3
Selection Guide Part No. Dice KA-2214SYSK Lens Type Super Bright Yellow (AlGaInP) Water Clear Viewing Angle [1] Iv (mcd) [2] @ 20mA Min. Typ. 2θ1/2 120 250 120° Notes: 1. θ1/2 is the angle from optical centerline where the luminous intensity is 1/2 of the optical peak value. 2. Luminous intensity/ luminous Flux: +/-15%. 3. Luminous intensity value is traceable to the CIE127-2007 compliant national standards. Electrical / Optical Characteristics at TA=25°C Symbol Parameter Device Typ.
PAGE 4
Super Bright Yellow KA-2214SYSK SPEC NO: DSAK1880 REV NO: V.3B DATE: DEC/03/2011 PAGE: 4 OF 6 APPROVED: WYNEC CHECKED: Allen Liu DRAWN: C.H.
PAGE 5
KA-2214SYSK Reflow soldering is recommended and the soldering profile is shown below. Other soldering methods are not recommended as they might cause damage to the product. Recommended Soldering Pattern (Units : mm; Tolerance: ± 0.1) Reel Dimension Tape Dimensions (Units : mm) SPEC NO: DSAK1880 REV NO: V.3B DATE: DEC/03/2011 PAGE: 5 OF 6 APPROVED: WYNEC CHECKED: Allen Liu DRAWN: C.H.
PAGE 6
PACKING & LABEL SPECIFICATIONS KA-2214SYSK SPEC NO: DSAK1880 REV NO: V.3B DATE: DEC/03/2011 PAGE: 6 OF 6 APPROVED: WYNEC CHECKED: Allen Liu DRAWN: C.H.