Datasheet

ManualsBrandsKINGBRIGHT ManualsLEDs & AccessoriesSMD LED PLCC2 Yellow 120 ° 150 mA 3 V

SPEC NO: DSAM4545 REV NO: V.2B DATE: MAR/29/2013 PAGE: 1 OF 6

APPROVED: WYNEC CHECKED: Allen Liu DRAWN: F.Cui ERP: 1201008298

3.5x2.8 mm SMD CHIP LED LAMP

Part Number: KA-3529ASYLZ4S

Super Bright Yellow

Features

zSingle color.

zSuitable for all SMT assembly and solder process.

zAvailable on tape and reel.

zWhite SMD package, silicone resin.

zLow thermal resistance.

zPackage: 2000pcs / reel.

zMoisture sensitivity level : level 2a.

zRoHS compliant.

Description

The source color devices are made with AlGaInP Light

Emitting Diode.

Static electricity and surge damage the LEDS.

It is recommended to use a wrist band or anti-electrostatic

glove when handling the LEDs.

All devices, equipment and machinery must be electrically

grounded.

Package Dimensions

Notes:

1. All dimensions are in millimeters (inches).

2. Tolerance is ±0.25(0.01") unless otherwise noted.

3. The specifications, characteristics and technical data described in the datasheet are subject to change without prior notice.

4. The device has a single mounting surface. The device must be mounted according to the specifications.

ATTENTION

OBSERVE PRECAUTIONS

FOR HANDLING

ELECTROSTATIC

DISCHARGE

SENSITIVE

DEVICES

Summary of content (6 pages)

PAGE 1
3.5x2.8 mm SMD CHIP LED LAMP Part Number: KA-3529ASYLZ4S ATTENTION Super Bright Yellow OBSERVE PRECAUTIONS FOR HANDLING ELECTROSTATIC DISCHARGE SENSITIVE DEVICES Features Description zSingle color. The source color devices are made with AlGaInP Light zSuitable for all SMT assembly and solder process. Emitting Diode. zAvailable on tape and reel. Static electricity and surge damage the LEDS. zWhite SMD package, silicone resin.
PAGE 2
Handling Precautions Compare to epoxy encapsulant that is hard and brittle, silicone is softer and flexible. Although its characteristic significantly reduces thermal stress, it is more susceptible to damage by external mechanical force. As a result, special handling precautions need to be observed during assembly using silicone encapsulated LED products. Failure to comply might lead to damage and premature failure of the LED. 1.
PAGE 3
Selection Guide Dice Part No. KA-3529ASYLZ4S Iv (cd) [2] @ 150mA Lens Type Super Bright Yellow (AlGaInP) Water Clear Φv (lm) [2] @ 150mA Viewing Angle [1] Min. Typ. Min. Typ. 2θ1/2 2.3 3.2 8.6 12 120° Notes: 1. θ1/2 is the angle from optical centerline where the luminous intensity is 1/2 of the optical peak value. 2. Luminous intensity/ luminous Flux: +/-15%. 3. LEDs are binned according to their luminous flux. 4.
PAGE 4
Super Bright Yellow SPEC NO: DSAM4545 APPROVED: WYNEC KA-3529ASYLZ4S REV NO: V.2B CHECKED: Allen Liu DATE: MAR/29/2013 PAGE: 4 OF 6 DRAWN: F.
PAGE 5
KA-3529ASYLZ4S Reflow soldering is recommended and the soldering profile is shown below. Other soldering methods are not recommended as they might cause damage to the product. Reel Dimension Recommended Soldering Pattern (Units : mm; Tolerance: ± 0.1) Tape Specifications (Units : mm) SPEC NO: DSAM4545 APPROVED: WYNEC REV NO: V.2B CHECKED: Allen Liu DATE: MAR/29/2013 PAGE: 5 OF 6 DRAWN: F.
PAGE 6
PACKING & LABEL SPECIFICATIONS SPEC NO: DSAM4545 APPROVED: WYNEC REV NO: V.2B CHECKED: Allen Liu KA-3529ASYLZ4S DATE: MAR/29/2013 PAGE: 6 OF 6 DRAWN: F.