USER MANUAL KB-50 / 100 / 170WX SINGLE ZONE WINE REFRIGERATORS KB50WX-FG KB100WX-FG KB170WX-FG KB170WX BORDERLESS BLACK GLASS DOOR SERIES KB100WX KB50WX GLASS DOOR WITH STAINLESS TRIM SERIES PLEASE NOTE: Every time the unit is powered ON, there will be a 6-minute delay for the compressor to start. COMPRESSOR WINE REFRIGERATORS www.kingsbottle.com.
CONTENTS TABLE OF CONTENTS Congratulations Congratulations and thank you for choosing our KingsBottle wine refrigerators. We are sure you will find your new appliance a pleasure to use. Before installing and operating the wine refrigerator, we recommend that you read through this manual which provides a description of your wine refrigerator and its functions.
SAFETY PART I IMPORTANT SAFETY INSTRUCTIONS 3. Please read this user manual carefully and store in a handy place later reference. placeforfor forlater later reference. place reference. The symbols you will see in this 4. The symbols you will see place for later reference.
FEATURES PART II DIAGRAM & DESCRIPTION OF REFRIGERATOR 1 Control board 2 Housing 3 Ventilation DC Fan 4 Shelf 5 Front grill 6 Door hinge 7 8 9 Controller Door Adjustable stand feet YOUR REFRIGERATOR ALSO INCLUDES TWO KEYS TO OPERATE THE ROUNDED LOCKING MECHANISM WHICH IS SHOWN AT THE LOWER CENTRE POSITION OF THE DIAGRAM. COMPRESSOR WINE REFRIGERATORS www.kingsbottle.com.
INSTALLATION PART III INSTALLATION INSTRUCTIONS CUTOUT DIMENSION ILLUSTRATED ” 26.97 23.54 ” ” 26.97 23.54 ” ” KB-170 SERIES 23.54”W x 26.97”D x 71.69”H (598W x 685D x 1821H mm) Included stand height 0.98”(25mm) KB-100 SERIES 23.54”W x 26.97”D x 55.43”H (598W x 685D x 1408H mm) Included stand height 0.98”(25mm) MODEL WIDTH DEPTH HEIGHT INCLUDED STAND HEIGHT KB-50 23.42” 595mm 23.62” 600mm 33.86” 860mm 0.79” 20mm KB-100 23.54” 598mm 26.97” 685mm 55.43” 1408mm 0.98” 25mm KB-170 23.
INSTALLATION PART III INSTALLATION INSTRUCTIONS 3. Compare the alignment of the appliance to the INSTALLING YOUR WINEcupboard. REFRIGERATOR surrounding The top of the appliance should 1. Move the unit into its final position. (CAUTION: for safety purpose, for the KB100 and KB170 models, it is necessary to anchor the beappliances levelto the from side tothe side diagram below). If wall, please refer to instruction(see on the next page.) 2.
Instructions to Anchor The Appliance to The Wall INSTALLATION B Rear of the refrigerator B A parts included A B 1. Area “A” is around 7”W x 2”H ( 180Wx50H mm ). This area is located 1.2 inch (30mm) from the edge of the appliance on top, left or right side (see above image). 2. “B” refers to the position where the holes for brackets should be drilled. Note: “B” should always be inside the area “A” 3. Position the brackets on the desired location, mark and drill pilot holes for the screws about 0.
STORAGE PART IV LAYOUT AND STORAGE display shelves options ( for KB170W Models) As an additional option, you might like the idea to have some display shelves to show your bottle label. You could refer to the instruction to remove the 2nd, 4th shelves at the top (use the screws to fill the holes on the wall after shelves removed), and then change the 1st, 3rd, 5th shelves to display shelves. Note: This changes will reduce the total storage capacity.
STORAGE PART IV LAYOUT AND STORAGE display shelves options ( for KB100W Models) As an additional option, you might like the idea to have some display shelves to show your bottle label. You could refer to the instruction to remove the 2nd shelf at the top (use the screws to fill the holes on the wall after shelves removed), and then change the 1st, 3rd shelves to display shelves. Note: This changes will reduce the total storage capacity.
STORAGE PART IV LAYOUT AND STORAGE YOUR CABINET WAS DESIGNED TO STORE A MAXIMUM NUMBER OF BOTTLES SECURELY. WE RECOMMEND THAT YOU OBSERVE THE TIPS BELOW TO OPTIMIZE LOADING. 1. 2. 3. 4. Disperse your bottles evenly so as not to concentrate the weight in any one area. Also, be careful that your bottles do not touch either the back of the cabinet or the step at the bottom. Also, make sure that bottles are not all grouped together either at the top or bottom of the cabinet.
OPERATION PART V OPERATING YOUR REFRIGERATOR ON/OFF TEMP. SET UP DOWN TEMP. DISPLAY LIGHT C/F SWITCH Each wine refrigerator includes an operating panel on the front of the unit. This operating panel includes several features to operate and control the temperature of both the upper and lower zones of the wine refrigerator. The operating panel includes the following features: ON/OFF: Turns the wine refrigerator power on or off. TEMP. SET: Displays the desired temperature. TEMP.
OPERATION ERROR CODE AND ALARM Code Description Solution E1 When the temp. In the UPPER zone is 4°F (2°C ) higher than the LOWER zone, E1 displays on the panel. With the temp. changes, and temp. in the UPPER zone is lower than the LOWER zone, E1 will disappear automatically. So, just wait for about one hour and check again. F1 When the evaporator temperature is lower than 0°F (-18°C ) F1 displays on the panel F1 meaning the refrigerator is at defrosting mode.
MAINTENANCE WARNING The refrigerator must be plugged into its own dedicated 220-240V, 50Hz AC electrical outlet. PART VI CARE AND MAINTENANCE The plug must be accessible when the refrigerator is place for later reference. in position. The symbols you will see in this booklet have these meanings: CLEANING YOUR WINE REFRIGERATOR It is essential the power point is properly earthed to ground. Consult a qualified electrician if you are unsure.
TROUBLESHOOTING GUIDE PART VII PROBLEM Refrigerator does not operate Refrigerator is not cold enough; can not cool down to the preset temp.
TECHNICAL DATA PART X TECHNICAL DATA KB170WX KB100WX KB50WX 14.30 CF ( 405 Liter ) 10.88 CF ( 308 Liter) 5.37 CF ( 152 Liter ) compressor with air-circulated fan cooling compressor with air-circulated fan cooling compressor with air-circulated fan cooling CLIMATE TYPE N N N ELECTRICITY PROTECTION GRADE I I I 220/240V/50-60HZ 220/240V/50-60HZ 220/240V/50-60HZ RATED CURRENT 1.64 A 1.64 A 1.
