+-++ MT12 User manual Container and Asset GPS Tracker
Declaration The contents of this manual is expected to be renewed from time to time without prior notice; the updated content will be added to the new version of this manual. KINGWO will improve or update the products or procedures described in the manual at any time. If there is a description of the product in the manual that does not match the actual product, the actual product shall prevail. KINGWO has the final interpretation rights of this manual.
Contents 1. Product features ................................................... 4 2. Technical Specification .............................................. 5 3. Functions ......................................................... 6 3.1 【Basic function】 ......................................................................................... 6 3.1.1 Position ................................................................................................. 6 3.1.2 AGPS .........................................
PART 01 Product Overview ● This product is designed for container and asset management; it can replace the air vent of the container, which will not affect the integrity of the container, or screwed to the assets that needs to be tracked. ● Long standby working time, if data upload interval is one packet per 24 hours, it would work about 3-5 years, this battery is capable of support different battery capacity to meet different requirements from customers.
PART 02 Technical Specification 2.1 【Parameter】 Characteristics Working Voltage Power Consumption Communication GSM GNSS Dimension Weight Waterproof Working Temperature Description Built in Unchangeable Lithium battery（3.6V， 5400～10800mAh） Optional 5400/8100/10800mAh Average working current<100mA;Sleep current<20uA; 4G network: TDD LTE/ FDD LTE network: WCDMA network: GSM/ GPRS 850/900/1800/1900MHZ Support GPS、BD Dual mode GPS L1:1575.42MHz,C/A Code BD B1: 1561.
PART 03 Functions 3.1 【Basic function】 3.1.1 Position Default upload is 24 hours per packet, the upload packet includes position status, longitude and latitude, GSM Signal Strength, GPS numbers, battery voltage etc, the upload interval can be configured 3.1.2 AGPS The device is with AGPS function, when the device connects to GPRS; AGPS is used for speeding up the position speed and improve the position accuracy 3.1.
3.1.5 Intelligent Tracking In case the container is stolen or in other emergency cases, a SMS can be sent or a command can be sent from the backend, when the device wake up, it will receive this command and enter into track mode, and upload the location data according to the preconfigured interval by customer until a stop tracking command is received 3.1.
3.2 【Extention/Optional Functions】 3.2.1 Light Sensor for removal alarm Built in high sensitive light sensor module, once the unit sense a light change from dark, it is considered the removal alarm been triggered. PART 04 Installation guide 4.
Screw Hole Green LED： Solid on-GPS fixed Blink：LBS Off：GPS not fixed Light sensor E-SIM Battery Switch Red LED： Fast blink：GPRS connecting Slow Blink：GPRS Connected Solid on：Module SIM card slot 8
4.2 【Installation and debugging】 4.2.1 SIM card installation Open the top cover of the device, insert the prepared SIM card into the SIM cardholder, and then confirm that the SIM card holder is well placed. Please make sure that the SIM card has the GPRS function available in advance and write down the SIM card number. If the device is with built in E-SIM, no need to insert SIM card 4.2.2Main Unit power on After installing the SIM card, turn the battery switch to the ON position.
4.3 【Key parameter setting】 4.3.1 Upload in sleep mode Command format：HX,T# Command description：T:wake up time，unit： minutes，default T：1440，value range :10-43200f minutes；for example，HX,1440#,set the wake up time is 1440 minutes (24 hours)。 Remark: Normally we use the default setting 1440, if set shorter wakeup time, the lifetime of the device will reduce 4.3.
Examples：LBS,1# enter LBS+WIFI position mode， Switch off GPS 4.3.
They are all clock points which will wake up at 8:00、 10:00、15:30、19:00 and upload device parameter info FALL,A# A=3 Open tamper alarm，no track A=2 Open tamper alarm，track 15 minutes，every 300 seconds A=1 Close tamper alarm A=0 Open tamper alarm，track 60 minutes，every 60 seconds Default :A=0 For example; FALL,0# ,Open tamper alarm，track 60 minutes， every 60 seconds UTC,TTTT# Set Time zone Range 780~-720 For example：UTC,480#,Platform positioning time is Beijing time Check device communication
Set standby server domain name as www.365qczx.com，port as 6000，communication mode UDP IP2,,0,0# delete standby server parameter MT12 Usage Requirements The users are required to strict using the device according to the operating instructions ,any disassemble, collide, charge, soak, over 80 °C, human failure, force majeure damage, etc. may cause short circuit, insufficient working time, battery deformation, liquid leakage, explosion, no warranty and compensation will be provided by Kingwo.
-- Contact us Shenzhen Kingwo IoT Co., Ltd +86 0755 86704262 marketing@kingwoiot.com www.itracksense.com www.kingwoiot.
