Operation Manual 12V Single Kit Part No.
KIT-140X 12V Single Kit, 12VDC Kit Contents: 2 12V Single Ballast xlr 2 15” 12V Single Fixture 2 Extension, 25ft 1 Car Adapter xlr 1 Alligator Clip Adapter xlr 1 Splitter xlr 1 Travel Case Dimensions 21 x 7.5 x 17” (53.5 x 19 x 43cm) Weight 14lbs (6.
Fixture is comprised of 3 parts: 1. Fixture Shell 2. Lamp Harness 3. Black Louver The Louver is held in place with Velcro fasteners. Clips hold the lamp to the fixture. Locking Lamp Connector: Depress both tabs on the lamp connector and apply to lamp pins. Push lamp into the fixture’s Lamp Holder Clips.
Most applications for the Fixture are in tight locations, where a strip of double sided Velcro or gaffer tape can hold the Fixture in place. For stand mounting, the Fixture is designed to accept a single mount plate, MTP-K1 (sold separately). Stand Mounting • • • • • Pull back the two push pins on the single mount. Insert the mount plate into the receptacle holes on the fixture mating plate. Push down on the two push-pins to lock the plate in place. Reverse the process to release the plate.
Ballast Operation continued…. (Note: The dimmer should be full up when striking the lamp. Once the lamp has come up to full temperature, in 3-5 minutes, then dim to the desired light level.) In cold temperatures the Ballast may take longer to ignite the lamp. If it does not ignite within 5 seconds, switch the ballast to OFF, and try again. If lamp does not strike after 2 or 3 attempts, turn Ballast off, check that the harness, lamp or any extension connections are secure and restrike.
Turn the DIMMER clockwise for maximum light output. The 12V Single ballast operates lamp lengths of 15”, 24”, 36” and 48” T12 or T8. The dimming range is different for each lamp length. The TRIM adjustment located under the carrying handle adjusts the dimming range to accommodate the various lamp lengths. The TRIM pot can also be used to make a lamp fade to black or to stop at a predetermined low light setting. To adjust the TRIM pot: Use a slotted screwdriver to turn the TRIM pot.
CFX-15V 15” Fixture/12V PWC-CX DC Car Adapter xlr, 6ft X04-25 Single Extension, 25ft PWC-X42 4-pin XLR Splitter BAL-140X 12V Single Ballast xlr, 12vdc KAS-12V 12V Single Travel Case PWC-AX DC Alligator Adapter xlr, 12ft Lamp Harness 4ft HAR-4801 3ft HAR-3601 2ft HAR-2401 15” HAR-1501 X04-A16 Single to 4Bank Combiner MTP-K1 Single mount plate with spare push-pins X04-A9 Single to Double Combiner PWS-137X Power Supply 7A, 100-250vac/ 12vdc, 4-Pin xlr 7
Kino Flo Lamp w/ Harness Dimensions Lamp Type 15” Med. Bi-Pin 2ft Med. Bi-Pin 3ft Med. Bi-Pin 4ft Med. Bi-Pin Length 15.5” 24.5” 36.5” 48.5” Width 1.5” 1.5” 1.5” 1.5” Kino Flo Single Fixture Dimensions Fixture Style Length Width 15” Single /12V 17.25” 3.25” 2ft Single 4ft Single 26.75” 51.50” 4.5” 4.5” Barndoor Weight Depth Width w/Lamps 2.75” 3.5” 3.5” N/A 3.5” 3.
BAL-140X 12V Single Ballast xlr, 12VDC Input Voltage: 12VDC Output Frequency: 25 kHz Amperage: F30/1.9A, F40/2.8A, F75/4.6A Dimming: 100% - 15% Lamp switching: on/off Ballast size: 7 x 6.5 x 2.5” (18 x 16.5 x 6.5cm) Weight: 2.2lb / 1.0kg Environmental: Disposal of Old Electrical & Electronic Equipment. This symbol on the product or on its packaging indicates that this product shall not be treated as household waste.
