Operation Manual Select LED 30/20 Part No.
Select LED Systems SYS-S30-120U SYS-S30-230U Select LED 30 DMX System, Univ 120U Select LED 30 DMX System, Univ 230U SYS-S20-120U SYS-S20-230U Select LED 20 DMX System, Univ 120U Select LED 20 DMX System, Univ 230U Each Select LED System consists of: 1 LED Fixture 1 Mounting Plate 1 Extension Cable 1 LED Controller Select LED System Components CFX-SL30 Select LED 30 Fixture CFX-SL20 Select LED 20 Fixture MTP-BC41 Kino 41K Mount w/ Baby Receiver Curve (16mm) X12-25 Select 150 Extension, 25ft LED
Select LED 30 DMX Kits KIT-S30B-120U Select LED 30 DMX Kit, Univ 120U w/ Soft Case KIT-S30B-230U Select LED 30 DMX Kit, Univ 230U w/ Soft Case Select LED 30 DMX Kit w/ Soft Case Kit Contents: 1 Select LED 30 Fixture 1 Select LED 150 DMX Controller 1 MTP-BC41 Mount w/ Baby Receiver Curve (16mm) 1 Extension, 25ft 1 Soft Case Dimensions: 42.5 x 7.5 x 16.
Select LED 20 DMX Kits KIT-S20B-120U Select LED 20 DMX Kit, Univ 120U w/ Soft Case KIT-S20B-230U Select LED 20 DMX Kit, Univ 230U w/ Soft Case Select LED 20 DMX Kit w/ Soft Case Kit Contents: 1 Select LED 20 Fixture 1 Select LED 150 DMX Controller 1 MTP-BC41 Mount w/ Baby Receiver Curve (16mm) 1 Extension, 25ft 1 Soft Case Dimensions: 31 x 7.5 x 18” (79 x 19 x 46cm) Weight: 23 lb (10.
Mounting the Fixture Align the center pin of the mounting plate to the center hole on the mating plate. Rotate plate clockwise until the four shoulder rivets drop into the receptacle. A locking pin will snap into place when the plate is properly seated. The yellow wire loop provides an attachment point for a safety chain. To remove the plate, pull up on the locking pin and reverse the mounting procedure. A 180° turn loosens the orientation of the mount. A right turn tightens the mount.
Mounting the Controller Insert the 4 rubber feet of the controller into the 4 holes in the fixture. Secure the Controller to the fixture with the Velcro fastening strap. Connect the harness to the Controller. Align the key ways on the harness connector with the circular receptacle on the ballast. Rotate the silver locking ring until it clicks into the lock position. Extension Cable The Select LED fixture can be used with the controller directly attached or remotely, using a 25ft extension cable.
Power AC Input The Select LED 150 DMX Controller is powered AC and includes an IEC connection. It also includes a 12ft power cord with a locking IEC connector. The Select LED 150 DMX Controller has a built-in power supply with universal input from 100-240VAC. Ambient Operating Temperature The Select LED 150 DMX is designed to operate at temperatures from 14°F to 104°F (-10°C to 40°C). DC Input The Select LED 150 DMX can also be operated on 24VDC (input range 18-36VDC) through a 3-Pin XLR.
Control Panel - White Mode A B C D E F G H A) On /Off: On = Green light displayed. Off = Red light displayed. The display and all menu settings can be operated while the power button is in the Off position, as long as power is applied to the controller. The On /Off button only controls the light source. B) Menu: Provides access to menu options such as General settings, Reset, DMX and DMX Wireless settings. Tip: While on control screen, press and hold for 3 seconds to switch to Color mode.
Control Panel - Color Mode A B C D E F G H A) On /Off: On = Green light displayed. Off = Red light displayed. The display and all menu settings can be operated while the power button is in the Off position, as long as power is applied to the controller. The On /Off button only controls the light source. B) Menu: Provides access to menu options such as General settings (Color Mode), Reset, DMX and DMX Wireless settings.
Menu Overview 10
Dimming Press the Mode button to select Dim. Rotating the control knob will dim the light of the fixture. Default setting is Fine. Press the rotating knob once to shift to Coarse. When the power is turned off or removed, the display will remember its last setting.
Kelvin Selection/Presets Press the Mode button until Kelvin is highlighted. Default Presets: 1 = 2700K 2 = 3200K 3 = 5000K 4 = 6500K Default setting is Fine. Press the control knob to shift to Coarse. Rotating the control knob will change the Kelvin.
In White mode, Kelvin custom settings between 2700K to 6500K and displayed G/M can be assigned to any preset button by holding down the desired button for 3 seconds. In Color mode, Kelvin custom settings between 2500K to 9900K and displayed G/M, Gel or Hue angle and Saturation can be assigned to any preset button by holding down the desired button for 3 seconds. The Kelvin display will flash once the setting is registered.
Green/Magenta The Select LED features a G/M (Green/Magenta) control to match the spectral sensitive curves of most popular cameras and other light sources. Green/Magenta Chart 100G +1 Green 50G +½ Green 25G +¼ Green 25M +¼ Magenta 50M +½ Magenta 100M +1 Magenta Press the Mode button until G/M is highlighted. Rotating the control knob to the right will adjust towards Green. Rotating to the left will adjust towards Magenta. Default setting is Fine.
Gel, Hue Angle & Saturation In Color mode (in addition to G/M control), Gel, Hue angle and Saturation adjustments are available. Kino Flo preset Gels and industry standard preset gels are included. Press Menu, select General and press control knob to change Mode to Color. Gel Press the Mode button until Gel is highlighted. Rotate the dimming knob to choose preset Gels. For DMX protocol for preset Gels, see www.kinoflo.com.
General Settings 16
Mode: White or Color Default is White mode. Custom Kelvin settings can be set between 2700K to 6500K. To change to Color mode, press the control knob. Custom Kelvin settings can be set between 2500K to 9900K. Timeout When choosing settings, if there is no activity, the display will default to Dim. The default for White mode is 5 seconds; the default for Color mode is 15 seconds, but can be changed by pressing the control knob to 0, 5, 15, 20 and 30 seconds. Smooth Default is On.
DMX DMX White mode: In White mode, the Select LED operates on three DMX channels using DMX512 while in the default 8 Bit Dim mode. The first channel operates dimming; 2nd channel operates Kelvin color temperature control from 2700K to 6500K; 3rd channel operates G/M. Once an address is selected, the fixture automatically assigns 3 channels. Color Mode In Color mode, the Select LED operates on six DMX channels using DMX512 while in the default 8 Bit Dim mode.
DMX Settings Press the Menu button to select DMX. Press and turn the control knob to select individual digit settings for a valid address from 1-512. On the main display, “X” next to DMX indicates DMX signal is present. All manual controls are disabled once the DMX cable is applied and DMX is turned on. To regain manual control with the DMX cable plugged in, set the DMX address to “0”. DIM Curve Default is Square. Press control knob to change to Linear.
DMX Wireless Settings The Select LED includes a built-in Lumen Radio receiver and can be operated wirelessly with a Lumen Radio transmitter (sold separately). DMX Wireless is an alternative to using DMX cables. Set DMX address as previously instructed on p 19. For more information on Lumen Radio Receiver/Transmitter, see www.LumenRadio.com.
Enable Enables wireless DMX. Default is OFF. Press the control knob to turn Enable ON. The following are examples of what will be seen in the main display when wireless DMX is Enabled: 1) “R” with no signal bar: Indicates wireless DMX is enabled, but there is no connection to a transmitter. 2) “R” with signal bar: Indicates wireless DMX is enabled; the fixture is connected to a transmitter, but no valid DMX is currently being transmitted.
Accessories DFS-SL30-H Select 30 Flozier, Half DFS-SL20-H Select 20 Flozier, Half DFS-SL30-S Select LED 30 Snapbag w/ 2 x Diffusion Select LED 20 Snapbag w/ 2 x Diffusion DFS-SL20-S LVR-SL340-S Select LED 30 Snapgrid 40° LVR-SL240-S Select LED 20 Snapgrid 40° LVR-SL390-P LVR-SL360-P LVR-SL290-P LVR-SL260-P Select 30 Louver/HP 90° Select 30 Louver/HP 60° Select 20 Louver/HP 90° Select 20 Louver/HP 60° MTP-KF41 Kino 41K Mount w/ 3/8” Pin (10mm) MTP-BF41S Kino 41K Mount w/ Baby Receiver Short (1
Cases BAG-SL30 Select LED 30 Soft Case BAG-SL20 Select LED 20 Soft Case KAS-DL30 Select LED 30 Flight Case KAS-DL20 Select LED 20 Flight Case KAS-SL32 Gaffer LED 30 Ship Case (2) KAS-SL22 Interview LED 20 Ship Case (2) KAS-SL33 Select LED 30 Fixture Ship Case (3) KAS-SL23 Select LED 20 Fixture Ship Case (3) Select LED Fixture Specifications CFX-SL30 Select LED 30 Fixture Weight: 12 lb (5kg) Dimensions: 40.5 x 10.5 x 3.5” w/ 6.5” barndoors (103 x 27 x 9cm w/ 16.
LED Controller Specifications LED-150X Select LED 150 DMX Controller Select LED 150 DMX Controller AC Input Voltage: 100~240VAC 50/60Hz, 150W Amperage VAC: 1.3A at 120VAC, 0.65A at 230VAC DC Input Voltage: 18~36VDC, 150W Amperage VDC: 7.0A at 24VDC Kelvin Range: 2700K~6500K (White Mode) Kelvin Range: 2500K~9900K (Color Mode) Dimming Range: 100%~1% Weight: 4.5 lb (2kg) Dimensions: 14.5 x 4 x 3” (37 x 10 x 8cm) FCC Part 15 Verification: This device complies with Part 15 of the FCC Rules.
