Operation Manual Foto-Flo 400 Part No.
KIT-F4-120 Foto-Flo 400 Kit, 120vac KIT-F4-230 Foto-Flo 400 Kit, 230vac Kit Contents: 1 Foto-Flo 400 Ballast 1 Foto-Flo 400 Fixture 1 Extension, 25ft 1 6-Lamp Carry Case 1 Travel Case .. Dimensions 54 x 21.5 x 9” (137 x 54.5 x 23cm) Weight 43lb (19.
CFX-F4 Foto-Flo 400 Fixture MTP-B41 Mount w/ Baby Receiver (16mm) X16-25 Extension, 25ft X16-12 Extension, 12ft BAL-422-120 Foto-Flo 400 Ballast, 120vac BAL-422-230 Foto-Flo 400 Ballast, 230vac Each System consists of: 1 Foto-Flo 400 Fixture 1 Mounting Plate 1 25ft Extension Cable 1 Foto-Flo 400 Ballast 3
The Foto-Flo 400 fixture is comprised of a removable Louver, Reflector, and Lamp Harness. The Louver and Reflector are held in place with Velcro fasteners. The Lamp Harness is secured by means of a ¼ turn fastener and two clips. To Release the Lamp Harness Remove the harness from 2 clips located under the reflector. Rotate the ¼ turn fastener clockwise to release harness.
Lamp Harness Color Codes BLACK/RED WHITE/YELLOW WHITE/BLACK BLACK/BLUE Foto-Flo 400 Harness The Harness wiring is color-coded. The same colorcode must match at each end of the lamp for proper operation. Locking Lamp Connector: Depress both tabs on lamp connector and apply to lamp pins. Match the Harness color-codes at each end of the lamp. Push lamps into the fixture’s Lamp Holder Clips.
Restricting the airflow around the lamps can cause the lamp to operate hotter. This increased heat will raise the lamp’s color temperature and green spike. Therefore, it is recommended to clip gels to the Doors of the Fixture. Do Not clip gels to louver. Do Not block the fixture ends in a manner that restricts airflow. Align the center pin of the mounting plate to the center hole on the mating plate. Rotate plate clockwise until the four shoulder rivets drop into the receptacle.
To remove the plate, pull up on the locking pin and rotate the plate counter clockwise. The standard mount comes with a Baby Receptacle Lollipop that mounts onto a baby stand. The ball and socket mount allows the fixture to be oriented in a broad range of angles. The Silver ring loops provide attachment points for a safety chain. MTP-L MTP-LBT Optional Lollipops allow mounting to grip heads or baby stands.
1. Connect the harness to the Ballast. Align the key ways on the harness connector with the circular receptacle on the ballast. Rotate the locking ring until it clicks into the lock position. 2. Insert the 4 rubber feet of the ballast into the 4 holes in the fixture. 3. Secure the Ballast to the fixture with the Velcro fastening strap. The Foto-Flo fixture can be used with the ballast directly attached or remotely, using a 25ft extension cable.
WARNING! 1) ALWAYS TURN OFF THE BALLAST BEFORE connecting or disconnecting Lamps, Harnesses or Extension Cables. 2) Use only with Sine wave inverters. Do not operate on SCR dimmers. 3) If powering the ballasts through a Dimmer Pack set the Dimmer to Non-Dim Mode. The 120 VAC Ballast requires 110 to 130 Volts AC 50/60 Hertz on an earth grounded circuit; the 230 VAC Ballast requires 220 to 240 Volts AC on an earth grounded circuit. The electronic Ballast operates at a high frequency of 25KHz.
MTP-B41 “Twist-On” Mount w/ Baby Receiver X16-25 4Bank Ext. Cable, 25ft X16-12 4Bank Ext.
MTP-L MTP-LB MTP-LBS MTP-LBT Lollipop 3/8” Pin Lollipop w/ Baby Receiver Lollipop w/ Baby Receiver Short Lollipop w/ Baby Receiver Straight X16-A4 4Bank to Single Splitter X16-A9 4Bank to Double Splitter DFS-4804 Foto-Flo 400 Flozier, Full DFS-4804-H Foto-Flo 400 Flozier, Half FIX-F4 HAR-F4 Foto-Flo 400 Fixture Shell Foto-Flo 400 Harness LVR-4804-B Foto-Flo 400 Louver, Black REF-4804 Foto-Flo 400 Reflector 11
EXP-LHC-T12 Lamp Holder Clips T12, 24pk EXP-M&T Adhesive Mounts and Releasable Ties, 25pk PRT-HLC Kino Locking Lamp Connector, 1 pk See web site: www.kinoflo.com for more repair parts KAS-C46 Part Number KAS-C46 KAS-F4-C Description Dimensions 6-Lamp Carry Case, 50.5 x 6 x 4” (4ft) (128.5 x 15 x 10cm) BAG-401 Weight (Empty) 1.5lb / .7kg Holds 4ft Lamps (6) KAS-F4-C Foto-Flo 400, Travel Case 54 x 21.5 x 9” (137 x 54.5 x 23cm) 22lb / 9.9kg BAG-401 53.5 x 7 x 14” (136 x 18 x 35.5cm) 4.6lb / 2.
Kino Flo Foto-Flo 400 Fixture Dimensions Barndoor Weight Fixture Style Length Width Depth Width w/Lamps Foto-Flo 400 52” 13” 3.5” 6.5” 11.5 lbs BAL-422-120 Foto-Flo 400 Ballast, 120VAC Input Voltage: 120VAC 50/60Hz Output Frequency: 25 kHz Amperage: F75/4.8A Lamp switching: 4 / 2 / off Ballast size: 9.5 x 9 x 2.5” (24 x 23 x 6.5cm) Weight: 4.3lb / 1.9kg BAL-422-230 Foto-Flo 400 Ballast, 230VAC Input Voltage: 230VAC 50/60Hz Output Frequency: 25kHz Amperage: F75/2.
Environmental: Disposal of Old Electrical & Electronic Equipment. This symbol on the product or on its packaging indicates that this product shall not be treated as household waste. This product is made of recyclable materials and should be disposed of in accordance with local and state regulations. Kino Flo, Inc. 2840 N. Hollywood Way, Burbank, CA 91505, USA Tel: 818 767-6528 website: www.kinoflo.