Operation Manual Image 82, 42, 22 4/14/03
Image 82 • 8 x 4ft lamps • Manual on/off switching control • Switches 2 lamps at a time Image 42 • 4 x 4ft lamps • Manual on/off switching control • Switches 2 lamps at a time Image 22 • 4 x 2ft lamps • Manual on/off switching control • Switches 2 lamps at a time Each System Includes: 1 Image Fixture 1 Silver Louver 1 Gel Frame 2
Insert lamps into both lamp connectors. Twist ¼ turn to make electrical contact. The gel frame is secured to the fixture by 4 spring-loaded pins. Align the pins of the gel frame with the oval receptacle holes on the edge of the fixture. Pull back the pins and release into the receptacles to properly secure the gel frame. A) The Gel Frame comes with Gel Clips. Cut the gel to size and use the Clips to fasten the gel to the Frame.
Place the long edge of the Louver into the lower channel containing a set of leaf springs. Press down on the Louver and slip the upper edge of the louver into the upper channel of the fixture. To remove reverse the procedure. The Image 82 requires a Junior Pin assembly or any other clamping device that uses a ½ inch bolt. The Image 82 uses the longer bolt. The Image 42 and 22 require the shorter bolt. Junior Pin Assembly The Baby Receiver is for use only on the Image 42 and Image 22.
The Image 82 Fixture is used for example purposes throughout these instructions. A B A ) Power Switch: Has a built-in indicator light, which can detect if AC power is present in power cord. "O" = OFF position B ) Fuse: Provides circuit protection. Note: If Fuse is blown or open replace with same type of fuse rating as marked. Provide 120 Volt AC primary power. Do not dim the fixture through a dimming circuit. If powering the fixtures through a dimmer board, set the dimmer profile to non-dim.
IMAGE 82, 42 and 22 Fixtures are operated manually with the Lamp Switches.
LVR-I80-B Image 82 Black Louver MTP-I80 Junior Pin for Image 82 Image 42 and 22 MTP-I40 Baby Receiver for Image 42 and 22 BRD-I80 Image 82 Barndoors, Set of 4 BRD-I40 Image 42 Barndoors, Set of 4 BRD-I20 Image 22 Barndoors,Set of 4 7
Side Door X2 Top and Bottom Door 1. For the Side Doors, align the hinge bracket tabs with the two square receptacles on the side of the fixture. 2. Press the tabs of both brackets into the square receptacles. 3. Slide the two brackets up until the silver lock pin snaps into place. 4. To release the Barndoor, press the Lock Pin down and slide the bracket in reverse.
1. For the Top and Bottom Doors, align the two hinge bracket tabs with the two square vents closest to the Silver Lock Pins. 2. Press the brackets down into the vent and slide them over to engage the Lock Pins with the hole in the bracket. 3. To remove the Barndoor, press down on the two Lock Pins and slide the brackets back. Adjust the hinge tension with a Philips head screwdriver.
Kas-I80-1 Part Number Kas-I80-2 Description Dimensions KAS-48 Weight (Empty) Holds KAS-I80-2 Image 82 Ship Case 56.25” x 16.25” x 35” 98 lb / 44Kg 1435mm x 413mm x 889mm Image 82 x 2 8KAS-I80-1 Image 82 Ship Case 56.5” x 7.75” x 35” 38lb / 17Kg 1435mm x 197mm x 889mm Image 82 x 1 KAS-I40-1 Image 42 Ship Case 56.5” x 10.25” x 23.25” 29lb / 13Kg 1435mm x 260mm x 590mm Image 42 x 1 KAS-I20-1 Image 22 Ship Case 31.25” x 10.25” x 23.
Model: Image 42 Power requirements: 120VAC or 230VAC Amperage: 5 amps at 120VAC, 2.5 amps at 230VAC Weight w/lamps: 22lb / 10Kg Dimensions: 54.5” x 20.25” x 6.25” 1384mm x 514mm x 159mm Lamp Switching: 4 / 2 / Off Lamp types: F40T12 Model: Image 22 Power requirements: 120VAC or 230VAC Amperage: 1.8 amps at 120VAC, .9 amps at 230VAC Weight w/lamps: 14lb / 6.3Kg Dimensions: 30.5” x 20.25” x 6.25” 775mm x 514mm x 159mm Lamp Switching: 4 / 2 / Off Lamp types: F20T12 Kino Flo, Inc.