Operation Manual Image 85/45 DMX Image 85 Yoke Mount Image 85 Pole-Op Part No.
Image Fixture Styles and Features Image Yoke Mount IMG-85X-120 Image 85 DMX Yoke Mount, 120VAC IMG-85X-230 Image 85 DMX Yoke Mount, 230VAC IMG-45X-120 Image 45 DMX Yoke Mount, 120VAC IMG-45X-230 Image 45 DMX Yoke Mount, 230VAC Image Pole-Op Mount IMG-85P-120 Image 85 DMX Pole-Op Mount, 120VAC IMG-85P-230 Image 85 DMX Pole-Op Mount, 230VAC IMG-45P-120 Image 45 DMX Pole-Op Mount, 120VAC IMG-45P-230 Image 45 DMX Pole-Op Mount, 230VAC 2
Included w/ all Image Models GFR-I80 Image 85 Gel Frame (Included) GFR-I40 Image 45 Gel Frame (Included) LVR-I80-S Image 85 Silver Louver (Included) LVR-I40-S Image 45 Silver Louver (Included) True Match® Lamps 488-K29-S 488-K32-S 488-K55-S 488-K10-S 488-K5-S 4ft Kino 800ma KF29 4ft Kino 800ma KF32 4ft Kino 800ma KF55 4ft Kino 800ma 420 Blue 4ft Kino 800ma 525 Green Note: Kino Flo recommends Safety-Coated 420nm Blue for Bluescreen and 525nm Green for Greenscreen.
Image 85 Yoke Mount Kits KIT-I85-X1/120 Image 85 DMX, Kit, 120VAC KIT-I85-X1/230 Image 85 DMX Kit, 230VAC Image 85 Yoke Kit Kit Contents: 1 Image 85 DMX Yoke Mount 1 MTP-I80 Mount 1 Ship Case Dimensions 56.5 x 8 x 35” (143.5 x 20.5 x 89cm) Weight 65 lb (29.3kg) KIT-I85-X2/120 Image 85 DMX, Kit, 120VAC (2-Unit) KIT-I85-X2/230 Image 85 DMX Kit, 230VAC (2-Unit) Image 85 Yoke Kit (2) Kit Contents: 2 Image 85 DMX Yoke Mount 2 MTP-I80 Mount 1 Ship Case Dimensions 56.5 x 16 x 35” (143.5 x 40.
KIT-I85-X4/120 Image 85 DMX, Kit, 120VAC (4-Unit) KIT-I85-X4/230 Image 85 DMX Kit, 230VAC (4-Unit) Image 85 Yoke Kit (4) Kit Contents: 4 Image 85 DMX Yoke Mount 4 MTP-I80 Mount 1 Ship Case Dimensions 35 x 33 x 64” (89 x 84 x 162.5cm) Weight 353 lb (160kg) Image 45 Yoke Mount Kits KIT-I45-X1/120 Image 45 DMX, Kit, 120VAC KIT-I45-X1/230 Image 45 DMX Kit, 230VAC Image 45 Yoke Kit Kit Contents: 1 Image 45 DMX Yoke Mount 1 MTP-I80 Mount 1 Ship Case Dimensions 56.5 x 9 x 23.5” (143.5 x 23x 59.
Inserting Lamps Insert lamps into both lamp holders. Twist ¼ turn to make electrical contact. Inserting Gel Frame The gel frame is secured to the fixture by 4 spring-loaded pins. Align the pins of the gel frame with the oval receptacle holes on the edge of the fixture. Pull back the pins and release into the receptacles to properly secure the gel frame. Applying Gel to Frame A) The Gel Frame comes with Gel Clips. Cut the gel to size and use the Clips to fasten the gel to the Frame.
Inserting Louver Place the long edge of the Louver into the lower channel containing a set of leaf springs. Press down on the Louver and slip the upper edge of the louver into the upper channel of the fixture. To remove reverse the procedure. Mounting Barndoors Side Door (x2) Top and Bottom Door 1. For the Side Doors, align the hinge bracket tabs with the two square receptacles on the side of the fixture. 2. Press the tabs of both brackets into the square receptacles. 3.
1. For the Top and Bottom Doors, align the two hinge bracket tabs with the two square vents closest to the silver lock pins. 2. Press the brackets down into the vent and slide them over to engage the lock pins with the hole in the bracket. 3. To remove the Barndoor, press down on the two lock pins and slide the brackets back. Adjust the hinge tension with a Phillips head screwdriver.
Image Yoke Mount The Yoke has a ½” hole to accept industry standard mounting hardware. The Image 85 Yoke Mount can hang from a grid by a junior pipe hanger using a Yoke Junior Pin (MTP-I80), sold separately. The Image 45 Yoke Mount can also hang from a grid by a junior pipe hanger using a Yoke Junior Pin (MTP-I80) or hang from a baby pipe hanger using a Yoke Baby Receiver (MTP-I40) also sold separately.
Pole Operation The Blue cup alters the Pan (left or right). The White cup alters the Tilt (up or down). Image Fixture DMX Control Panel The Image 85 Fixture is used for example purposes throughout these instructions. A B C D E F G H I J A) Remote Jack: Input for remote hand-held lamp control. Turns lamps on and off manually without connecting to DMX. B) Manual Selector Dial: Turns lamps on and off manually without connecting DMX Cable to Fixture.
I) DMX-In & DMX-Out: DMX-IN receives DMX signals from Dimmer Board. DMX-OUT relays DMX signal through to other Fixtures or Instruments. J) DMX TERMINATE Switch: Terminates DMX signal at the end of Fixture series. IMPORTANT! The dimmer board/light console should have its channel set to LINEAR light output response. (LINEAR response is the default setting on most dimmer boards.) Power Requirements Provide 120 Volt AC primary power. Do not dim the fixture through a dimming circuit.
DMX Image 85 Switching DMX Image 45 Switching Note: Manual lamp switching, HO/STD as well as remote hand-held control (DIM-5) is disabled as soon as DMX cables are applied. For Manual control with DMX cables plugged in, set address to “000”. There is a 5 second delay when switching between DMX and Manual control. DMX Operation DMX Addressing Prior to hanging any instruments set the DMX address of each Fixture. Push the tabs above or below the number window to set the address.
Image 85 - Each Image 85 fixture operates on 9 addresses. After the first DMX address is entered, the Image 85 Fixture automatically captures 9 addresses to lamps 1 – 8 and the 9th address to control the HO/STD Select feature. For the sake of simplification, it is advisable to select address sequences such as 10, 20, 30, 40 and so on. th The 9 address controls the HO/STD setting of all the lamps in the fixture. A dimmer level of 0%~50% sets the lamps in the HO mode.
DMX Cables The Fixture uses five-pin XLR male and female connectors to receive DMX signals from the Dimmer Board and jumper the Fixtures in a series. DMX pin-out wiring follows the USITT DMX512 standard: Do Not use Microphone Cables and other general purpose, two-core Cables designed for audio or signaling use. They are not suitable for DMX512. Problems due to incorrect cabling may not be immediately apparent.
One of the best applications for the Fixture mode is when lighting Blue and Green Screens or large Cycloramas. For example: One row of Image 85 fixtures can be set to Fixture mode on a common address. When the fader on the dimmer board is brought up or down, all the Fixtures on that address will have the same lamps turned on. Assigning the 9th address on all the fixtures renders control over the HO/STD settings.
Individual Lamp Mode Setting the unit to Individual Lamp mode allows each lamp within the fixture to have its own address. Although this option will use up a lot of addresses, it may be preferable for certain situations. The Individual Lamp mode is useful in achieving light effects like flickering, chasing or creating light patterns. After the first DMX address is entered, the DMX Image 85 automatically captures th 9 addresses. Lamps are on addresses 1- 8. The 9 address controls the HO/STD mode.
Accessories LVR-I80-B Image 85 Black Louver MTP-I80 Yoke Junior Pin MTP-I40 Yoke Baby Receiver XLR-515 DMX Cable 5 Pin, 15ft XLR-525 DMX Cable 5 Pin, 25ft BRD-I80 Image 85 Barndoors, set of 4 BRD-I40 Image 45 Barndoors, set of 4 DIM-5 Remote Lamp Selector 17
True Match ® Lamps 488-K29-S 488-K32-S 488-K55-S 488-K10-S 488-K5-S 4ft Kino 800ma KF29 4ft Kino 800ma KF32 4ft Kino 800ma KF55 4ft Kino 800ma 420 Blue 4ft Kino 800ma 525 Green Note: Kino Flo recommends Safety-Coated 420nm Blue for Bluescreen and 525nm Green for Greenscreen. Cases KAS-I80-1 Part Number KAS-I80-2 Description Dimensions KAS-I80-4 Weight (Empty) Holds KAS-I40-1 Image 45 Ship Case (1) 56.5 x 9 x 23.5” (143.5 x 23 x 59.5cm) 27lb / 12.
Fixture Specifications IMG-85X Image 85 DMX Yoke Image 85 Yoke Power Requirements: 120VAC or 230VAC Amperage: 8.6 amps at 120VAC, 4.3 amps at 230VAC Weight w/ lamps: 38lb / 17.1kg Dimensions: 54 x 28 x 6.5” (137 x 71 x 16.5cm) Lamp Select Switch: Rotary 1-8 Power Switch: On/Off (Lighted when On) Remote Lamp Select: Phono jack input for remote control Lamp type: F75T12 IMG-45X Image 45 DMX Yoke Image 45 Yoke Power requirements: 120VAC or 230VAC Amperage: 4.5 amps at 120VAC, 2.
IMG-85P Image 85 DMX Pole-Op Image 85 Pole-Op Power Requirements: 120VAC or 230VAC Amperage: 8.6 amps at 120VAC, 4.3 amps at 230VAC Weight w/ lamps: 40lb / 18kg Dimensions: 54.5 x 28 x 6.5” (138.4 x 71 x 16.5cm) Lamp Select Switch: Rotary 1-8 Power Switch: On/Off (Lighted when On) Remote Lamp Select: Phono jack input for remote control Lamp type: F75T12 IMG-45P Image 45 DMX Pole-Op Image 45 Pole-Op Power requirements: 120VAC or 230VAC Amperage: 4.5 amps at 120VAC, 2.