Operation Manual VistaBeam ® 610 & 310 DMX VistaBeam 610 Center VistaBeam 610 Pole-Op Part No.
VistaBeam Fixture Styles and Features VistaBeam Center Mount VIS-610C-120 VistaBeam 610 DMX Center Mount, 120VAC VIS-610C-230 VistaBeam 610 DMX Center Mount, 230VAC VIS-310C-120 VistaBeam 310 DMX Center Mount, 120VAC VIS-310C-230 VistaBeam 310 DMX Center Mount, 230VAC VistaBeam Yoke Mount VIS-610Y-120 VistaBeam 610 DMX Yoke Mount, 120VAC VIS-610Y-230 VistaBeam 610 DMX Yoke Mount, 230VAC VIS-310Y-120 VistaBeam 310 DMX Yoke Mount, 120VAC VIS-310Y-230 VistaBeam 310 DMX Yoke Mount, 230VAC VistaBeam Pole-Op Mo
Included w/ all VistaBeam Models GFR-V6 VistaBeam 610 Gel Frame (Included) GFR-V3 VistaBeam 310 Gel Frame (Included) LVR-V690 VistaBeam 610 Louver 90° (Included) LVR-V390 VistaBeam 310 Louver 90° (Included) True Match® Lamps 964-K32 96W Kino KF32 Twin 964-K55 96W Kino KF55 Twin 3
VistaBeam Center Mount Kits KIT-V6C-120 VistaBeam 610 Center Mount Kit, 120VAC KIT-V6C-230 VistaBeam 610 Center Mount Kit, 230VAC Kit Contents: 1 VistaBeam 610 Center Mount 1 Ship Case Dimensions 41.5 x 15.5 x 44” (105.5 x 39.5 x 112cm) Weight 135 lb (61kg) KIT-V3C-120 VistaBeam 310 Center Mount Kit, 120VAC KIT-V3C-230 VistaBeam 310 Center Mount Kit, 230VAC Kit Contents: 1 VistaBeam 310 Center Mount 1 Ship Case Dimensions 42 x 14.5 x 25.5” (107 x 37 x 65cm) 4 Weight 79.
Inserting Lamps 1 2 3 4 1) Open the two hinged reflector panels. 2 & 3) Insert the lamp base into the lamp connector. 4) Insert the lamp tip into the lamp clip. Close the reflector panels. Inserting Gel Frame Align the pins of the Gel Frame with the inner (closest to lamps) holes of the Accessory Holder. Pull back the pins and release into the holes to secure the gel frame.
Applying Gel to Frame A B A) The Gel Frame comes with Gel clips. Cut the gel to size and use the clips to fasten the gel to the frame. Note: It is recommended to attach one clip on all four sides and two clips near all four corners of the Gel Frame. B) Another method is to apply transfer tape directly to the gel frame. The clips are not necessary when taping the gel. Inserting Louver Align the pins of the louver with the outer (farthest from lamps) receptacle holes on the Accessory Holder.
VistaBeam Center Mount The VistaBeam Center Mount allows the fixture to mount to a junior stand or hang from a pipe grid with junior pipe clamp. The Center Mount includes a Junior Stand Adapter (MTP-V63JR) which can be mounted onto a junior stand. Center Mount Rotation and Tilt Controls 1) The black knob controls the tilt. 2) The gold lock lever controls the rotation of the fixture. 3) For further control, the center mount also rotates at 90° stops. Pull locking pin and turn counter-clockwise to unlock.
Center Mount Speed-Rail Rigging The mount fittings are U.S. industry standard “Speed Rail” 1 ¼” fittings. They accept a 1 5/8” outside diameter pipe. These fittings enable custom frames to be constructed for special rigging applications such as multiple fixture hangs. VistaBeam Yoke Mount The yoke has a ½” hole to accept industry standard hardware. The VistaBeam 610 and 310 Yoke Mount fixtures can hang from a junior pipe hanger using a Junior Pin Assembly for Yoke (MTP-I80), sold separately.
VistaBeam Pole-Op Mount The VistaBeam 610 and 310 Pole-Op Mount fixtures include a yoke with an attached junior pin. They can be hung from a grid with a junior pipe hanger. Junior pin attached to Pole-Op Yoke Operating Pole-Op The Blue cup alters the Pan (left or right). The White cup alters the Tilt (up or down). Warning! Do not pull yoke to adjust tilt. Turn the white knob counter clockwise to angle the yoke 90°. (ParaBeam shown for illustration purposes only.
VistaBeam DMX Control Panel A B C D F E G A) DMX-IN & DMX-OUT: DMX-IN receives DMX signals from Dimmer Board. DMX-OUT relays DMX signal through other Fixtures or Instruments. Note: Each VistaBeam 610 & 310 DMX fixture has an “AUTO TERMINATE” feature. The last fixture that does not have an XLR cable attached to the DMX “Out” port will automatically terminate. B) Indicator Light: Lights if valid DMX signal is present.
Power & Fuse Requirements POWER Provide 120VAC or 230VAC depending on model. Do not dim the fixture through a dimming circuit. If powering the fixtures through a dimming board, set the dimmer profile to non-dim. FUSE Fuse provides circuit protection. Note: If Fuse is “blown” or “open”, replace with same type of fuse rating as marked. Load Considerations: The Kino Flo ballasts used in the VistaBeam are not power factor corrected.
Manual Operation The VistaBeam DMX fixtures may be operated with the Manual Lamp Selector Knob. The selector knob enables you to turn lamps on and off with an “inside-out” pattern (i.e., if all lamps are on, the outside tubes will turn off first). VistaBeam 610 Lamp Switching VistaBeam 310 Lamp Switching HO operates lamps in High Output mode. STD operates lamps in Standard Output mode. Note: All manual functions are disabled as soon as DMX cables are applied.
DMX Channels The VistaBeam 610 operates on DMX Channel 1 or 7. On DMX Channel 1, one DMX address controls all 6 lamps on one dimmer channel. Channels 2-6 not used. A 7th address controls the HO/Std setting. Not assigning the 7th address results in the fixture operating at the HO setting. On DMX Channel 7, the first six DMX addresses control 6 lamps individually.
Dimmer level – Lamp response Sliding the fader on the dimmer board from 0~100 controls the number of lamps that are on within a fixture. Note: The lamps may respond ± 4 channel levels, depending on the dimmer board. See diagrams below.
VistaBeam 610 Lamp Sequence (DMX Channel 7) VistaBeam 610 DMX Address Sequence (DMX Channel 7) Lamp # DMX Address Lamp 1 1 Lamp 2 2 Lamp 3 3 Lamp 4 4 Lamp 5 5 Lamp 6 6 HO/STD 7 VistaBeam 310 Lamp Sequence (DMX Channel 4) VistaBeam 310 DMX Address Sequence (DMX Channel 4) Lamp # DMX Address Lamp 1 1 Lamp 2 2 Lamp 3 3 HO/STD 4 15
Auto Terminate Feature The VistaBeam 610 and 310 series have an “AUTO TERMINATE” feature. The last fixture that does not have an XLR cable attached to the DMX “Out” port will automatically terminate. Any theatrical lighting board with DMX512 protocol can be used to individually turn on/off lamps in a fixture. VistaBeams can be jumpered using the IN and OUT ports. As many as 100 fixtures can be jumpered on one chain as long as the DMX cable run remains under 1000 feet or 40 x 25ft DMX cables.
Accessories and Parts GFR-V6 VistaBeam 610 Gel Frame GFR-V3 VistaBeam 310 Gel Frame LVR-V690 LVR-V660 LVR-V645 LVR-V390 LVR-V360 LVR-V345 VistaBeam 610 Louver, 90° VistaBeam 610 Louver, 60° VistaBeam 610 Louver, 45° VistaBeam 310 Louver, 90° VistaBeam 310 Louver, 60° VistaBeam 310 Louver, 45° MTP-V63C VistaBeam 63 Center Mount Assembly MTP-V63H1 VistaBeam 63 Center Hanging Adapter (28mm) MTP-V63JR VistaBeam 63 Junior Adapter (28mm) XLR-515 DMX Cable 5-Pin XLR, 15ft XLR-525 DMX Cable 5-Pin XLR
True Match® Lamps 964-K32 96W Kino KF32 Twin 964-K55 96W Kino KF55 Twin Cases KAS-V61 KAS-VL8-C KAS-V31 Part Number Description Dimensions KAS-V61 VistaBeam 610 Center Ship Case 41.5 x 16 x 44” (105.5 x 40.5 x 112cm) 93 lb (42kg) VistaBeam 610, Louver (2) KAS-V31 VistaBeam 310 Center Ship Case 41.5 x 14.5 x 25.5” (102.5 x 37x 65cm) 53 lb (24kg) VistaBeam 310, Louver (2) KAS-VL8 VistaBeam 8-Lamp Ship Case 38 x 7 x 14” (96.5 x 18 x 36cm) 13.
Fixture Specifications Model: VIS-610C VistaBeam 610 DMX Center Mount VistaBeam 610 Center Mount Power Requirements: 120VAC or 230VAC Amperage: 8.0 amps at 120VAC 4.7 amps at 230VAC Lamp Switching: 1~6 Output Switching: HO/Std Weight w/ lamps: 46.5 lb / 21kg Dimensions: 37.5 x 35.5 x 8.5” (95.5 x 90 x 21.5cm) Lamp type: 96W CFL Model: VIS-610Y VistaBeam 610 DMX Yoke Mount VistaBeam 610 Yoke Mount Power Requirements: 120VAC or 230VAC Amperage: 8.0 amps at 120VAC 4.
Model: VIS-310C VistaBeam 310 DMX Center Mount VistaBeam 310 Center Mount Power Requirements: 120VAC or 230VAC Amperage: 4.0 amps at 120VAC 2.4 amps at 230VAC Lamp Switching: 1~3 Output Switching: HO/Std Weight w/ lamps: 28.5 lb / 13kg Dimensions: 37.5 x 20 x 9” (95.5 x 51.5 x 23cm) Lamp type: 96W CFL Model: VIS-310Y VistaBeam 310 DMX Yoke Mount VistaBeam 310 Yoke Mount Power Requirements: 120VAC or 230VAC Amperage: 4.0 amps at 120VAC 2.
