Congratulations Kirby Sentria in Moscow - $2000 - Tel: (495) 506-9032 Dear Kirby Customer, Congratulations on your purchase. You now own a superior, complete home care system designed to help make your home and furnishings look better and last longer. Most importantly, repeated use of your Kirby Sentria™ system will give you the type of clean in-home environment you want and deserve.
Important Safety Instructions WHEN USING AN ELECTRICAL APPLIANCE, BASIC PRECAUTIONS SHOULD ALWAYS BE FOLLOWED. BE FAMILIAR WITH ALL THE IMPORTANT SAFETY INSTRUCTIONS BEFORE USING YOUR Sentria HOME CARE SYSTEM. WARNING - To reduce the risk of fire, electric shock or injury: • Do not leave appliance unattended when running or plugged in. Unplug from outlet when not in use and before servicing. • Do not use outdoors. Use only on dry surfaces or with the Kirby Carpet Shampoo System. Do not expose to rain.
Table of Contents Important Safety Instructions About this Manual Kirby® Micron Magic® HEPA Filtration Part 1 - Getting Started Moving Your System/Handle Tilt Latch Lock/Toe-Touch Control Power Nozzle Height Adjustment/Tech Drive® Power Assist Installing/Changing Disposable Filter Bags Bag Support Strap/Mini Em-Tor® Collector/The Belt Lifter Part 2 — Upright & Portable Cleaner Upright Cord Management The Upright Cleaner Straight Suction Cleaner The Portable Cleaner Part 3 — Canister Cleaner & Attachments Co
About This Manual This Owner's Manual was designed to be easy to read and follow. It has been organized in sections based on the various ways you may use your new Kirby ® Sentria™ system. Within each section, simple step-by-step illustrations will help you easily visualize the steps required to properly operate your new Sentria system and its many attachments and optional accessories.
MICRON MAGIC® • • • • HEPAFILTRATION With MicroAllergen Technology You bought the best; you expect the best. That's why the Kirby Company developed the Micron Magic HEPA (High Efficiency Particle Arrest) Filtration System featuring the latest in clean air technology without sacrificing tremendous airflow. Your new Sentria™ system includes our BEST filters: • Traps over 99% of particles as small as 0.
Getting Started PART ONE This section outlines general information you will need as you begin using your new Sentria™ system.
Getting Started MOVING YOUR SYSTEM Your Sentria system is equipped with Tech Drive ® power assist. In order to push your unit with the motor OFF, the Tech Drive Pedal (11) must be turned OFF (disengaged). Turn Tech Drive power assist OFF by pushing down on the gray "N" side (marked "N" for Neutral) of the Tech Drive N/ D Pedal. (See page 8 for additional information.) CARRYING YOUR SYSTEM NOTE: The Carrying Grip (18) is designed for convenience in carrying your Sentria system.
Getting Started POWER NOZZLE HEIGHT ADJUSTMENT When using the Power Nozzle (25), it is important to adjust the height properly. Start by pressing the Toe-Touch Control Bottom Pedal (9) all the way down, raising the front of your system all the way up. The Toe-Touch Control adjusts the Power Nozzle to seven different heights. The highest four positions are used for attaching accessories. Positions #1-3 are used for carpet and floor cleaning.
Getting Started TURNING TECH DRIVE POWER ASSIST OFF (NEUTRAL) To move your Sentria™ system with the motor OFF or to vacuum without power assist, Tech Drive power assist must be put in Neutral. To place Tech Drive power assist in Neutral, push down the gray "N" side (marked "N" for Neutral) of the Tech Drive N/D Pedal (11). • INSTALLING/CHANGING DISPOSABLE FILTER BAGS A Disposable Filter Bag must be installed before you begin vacuuming.
Getting Started BAG SUPPORT STRAP 4 Check to make sure the Bag Support Strap (4)is connected to the Top Adaptor (5). The Bag Support Strap provides the support required for proper operation of the Disposable Filter Bag. If it is not connected, thread the strap through the small hole of the Top Adaptor. Then place the hole in the strap over the stud on the Top Adaptor. Finally, insert the adaptor and new filter bag into the Outer Permanent Bag (1)and close the zipper completely for maximum performance.
Getting Started USING THE BELT LIFTER (cont) 1 To use the Belt Lifter, you must first raise the Headlight Hood (21). > 2 Flip out the handle on the Belt Lifter (20). Use it to turn the Belt Lifter fully to the left (counter-clockwise) until it stops and the red arrows line up. This stretches the belt and lifts it off the motor shaft. Return the handle on the Belt Lifter to its closed position. If you are using your Sentria™ system as a straight suction cleaner, simply lower the Headlight Hood.
Upright & Portable Cleaner PART TWO Your Sentria™ home care system is extremely versatile.
Upright & Portable Cleaner UPRIGHT CORD MANAGEMENT The Sentria system Upright handle incorporates a series of hooks and fasteners to keep the cord off the floor and attached to the upright handle for your convenience. 1 When using your Sentria system as an upright, snap the power cord into the two cord holders located on the back of the handle.
Upright & Portable Cleaner THE UPRIGHT CLEANER Before you begin vacuuming, it's important to have the Power Nozzle (25) adjusted to the proper height setting. This gives you the most efficient cleaning action. Lowering the Power Nozzle too far prevents proper cleaning and shortens belt life. The proper height setting can be achieved by doing the following: > 1 2 Before you turn the Sentria™ system ON, raise the Power Nozzle by stepping on the Toe Touch Control Bottom Pedal (9) all the way down.
Upright & Portable Cleaner 4 If desired, engage Tech Drive® power assist by pushing down the red "D" side (marked "D" for Drive) of the Tech Drive N/D Pedal (12) located just below the Power Switch (13). > 5 To turn your Sentria™ system OFF, press the ToeTouch Control Bottom Pedal (9) all the way down until nozzle is fully raised. Disengage Tech Drive power assist by stepping on the gray "N" side (marked "N" for Neutral) of the Tech Drive N/D Pedal (11).
Upright & Portable Cleaner THE HARD FLOOR PAD (optional) By attaching the optional Hard Floor Pad to your Sentria™, system you may dust bare floors. While the unit is turned OFF, raise the Power Nozzle (25) as far as it will go by pressing the Toe-Touch Control Bottom Pedal (9). Attach the Hard Floor Pad onto the nozzle opening using the spring clips on the plate. Then lower the Power Nozzle by pressing the Toe-Touch Control Upper Pedal (8) one notch at a time until the bristles touch the floor.
Upright & Portable Cleaner PORTABLE CLEANER SET-UP (cont) 4 Bend the Filtration Bag Assembly (1) in half and insert the Bag Latch Tab (2) into the slot on the Portable Handle until it snaps into place. You are now ready for portable power cleaning. • NOTE: Do not use portable mode on upholstered furniture. CARPETED STAIRS Place your Sentria™ system on one of the carpeted steps, while supporting the rear.
Canister Cleaner & Attachments PART THREE Your Kirby ® Sentria™ system comes with a wide variety of attachments for added versatility.
Canister Cleaner & Attachments CONVERTING TO A CANISTER CLEANER/ INSTALLING THE ATTACHMENT HOSE When using different cleaning attachments, the Attachment Hose is connected to the front of the cleaner in place of the Power Nozzle (25). NOTE: When connecting the Attachment Hose, you may choose between the Upright Handle (17) or the Portable Handle (15). To install the Portable Handle, see page 16. To install the Attachment Hose, you must first convert to a Canister by removing the Power Nozzle.
Canister Cleaner & Attachments INSTALLING ATTACHMENTS ON THE ATTACHMENT HOSE To attach tools to the hose, push lightly while twisting the smaller end of the hose into the tool. • EXTENSION TUBES One or two Extension Tubes can be attached to the end of the hose to extend your reach and efficiently use various attachments. • SURFACE NOZZLE UNDER LOW FURNITURE/BARE FLOORS The Surface Nozzle should be used on bare floors or for surface cleaning carpets and under low furniture.
Canister Cleaner & Attachments UPHOLSTERY NOZZLE The Upholstery Nozzle is used for cleaning upholstered furniture, carpeted steps, and clothing. It can also be used to clean the inside of cars. • CREVICE TOOL WITH REMOVABLE BRUSH Without the removable brush, the Crevice Tool can be used for cleaning cracks, crevices, corners, grooves and narrow openings. Install the removable brush in the end of the Crevice Tool to remove dirt from corners, button tufts, between radiator coils and sliding window tracks.
Canister Cleaner & Attachments MASSAGE CUP Used with the Attachment Hose, the Massage Cup provides an invigorating skin or scalp massage. It can also be used to clean the floors of cars. • CONTROLLING AIRFLOW WITH THE SUCTION CONTROL GRIP Sometimes when using the attachments, vacuuming drapes or delicate lamp shades, for example, you might wish to control the amount of suction. The Suction Control Grip features a valve to control the amount of suction.
Canister Cleaner & Attachments BLOWER SET-UP Your Sentria system can also be used as a blower. To do so, you must first remove the Power Nozzle (25). NOTE: When using your Sentria system as a blower, you may choose between the Upright Handle (17) or the Portable Handle (15). 1 Turn the power OFF, place the Tech Drive® power assist in Neutral (see page 8 for details), unplug the unit from the wall outlet and press the Toe-Touch Control Bottom Pedal (9) all the way down until nozzle is fully raised.
Canister Cleaner & Attachments BLOWER SET-UP (cont) 5 To remove the entire Bag Assembly, grasp the Mini Em-Tor ® collector (6) in the hand-hold provided and rotate it out and away from the Sentria system as far as it will go. Then lift it off. Release the Outer Permanent Bag Top from the Bag Support by pressing the Bag Release Button (16) and sliding the bag top down. > 6 Place the large end of the Attachment Hose over the Air Exhaust Port (19).
Canister Cleaner & Attachments THE PORTABLE SPRAYER The Portable Sprayer is used only in the Blower Mode. It is an excellent tool to apply many different types of water-based liquids to any type of surface. The spray can be adjusted ranging from very fine to coarse. PORTABLE SPRAYER SET-UP 1 2 Unscrew the jar from the Portable Sprayer and fill 3/4 full with non-flammable liquid. Before reinstalling the jar, make sure the portable sprayer dip tube is attached to the spray gun body.
Canister Cleaner & Attachments USING THE PORTABLE SPRAYER (cont) 2 With the nozzle pointed away from you, adjust the spray by turning the Spray Adjustment Control on the trigger of the Portable Sprayer. > 3 Use slow, sweeping motions to spray the desired area with solution. Always squeeze the trigger fully to permit maximum flow. This will give you the best spray control.
Canister Cleaner & Attachments CLEANING THE PORTABLE SPRAYER (cont) The spray opening on the front of the Sprayer also pulls out so that the inside of the Sprayer and the nozzle jet can be cleaned. 3 To remove the nozzle jet, press on the two latches on the front of the nozzle jet and pull it out. (The latches must be aligned with the holes on the front of the Sprayer when returning the nozzle jet to the front of the Sprayer.) Then, fill the jar with water. Spray water until the spray becomes clear.
Canister Cleaner & Attachments USING THE PORTABLE SHAMPOOER 1 Before shampooing, vacuum surface thoroughly. To make suds, turn the Sentria™ system ON and pull the trigger of the Portable Sprayer. A stream of suds will come out of the cap. The suds can be sprayed directly onto the surface being cleaned or on a plain paper bag or in a bowl and then applied to the surface being cleaned. > 2 Adjust the Portable Sprayer for proper suds volume by turning the Spray Adjustment Control located on the trigger.
Optional Accessories PART FOUR Optional Kirby® Accessories greatly enhance the usefulness of your new Sentria™ system.
Optional Accessories CARPET SHAMPOO SYSTEM SET-UP Vacuum thoroughly before shampooing for maximum cleaning. Then, remove the Outer Permanent Bag (1) and the Power Nozzle (25) to prepare for shampooing. 1 By using the handle, turn the Carpet Shampoo System Nozzle Belt Lifter to the right (clockwise) until the green arrows line up. > 2 Slide the slots on the side of the Carpet Shampoo System Nozzle over the outer shoulders of the Carpet Shampoo System Tray.
Optional Accessories CARPET SHAMPOO SYSTEM SET-UP (cont) 5 While sliding the Carpet Shampoo System Nozzle/ Tray Assembly toward the Sentria™ system and over the Motor Shaft (23), connect the hooks on the bottom rear of the nozzle to the Attaching Bar (24). > Push the nozzle up against the unit and turn the Accessory Lock (22) to the right (clockwise) to lock the nozzle in place.
Optional Accessories CARPET SHAMPOO SYSTEM SET-UP (cont) Taking care to avoid spilling liquid on the Sentria™ system or the floor, place the opening in the bottom front of the Shampoo Tank over the Air Exhaust Port (19) on the unit. Angle the Shampoo Tank outward from the unit until the arrows line up. Next, slide the Shampoo Tank down over the locking pins on the Air Exhaust Port. 8 Rotate the Shampoo Tank toward the unit (clockwise) to lock it in place.
Optional Accessories USING THE CARPET SHAMPOO SYSTEM (cont) As you move the Sentria™ system back and forth, foam will be released and the brush will work it into the carpet. NOTE: Suds should be dispensed the full width of the tray when the unit is pulled backward. If not, pull back more slowly or check and clean the Shampoo Tank Filter, if necessary (see page 35). After suds have been on the carpet at least five minutes, pick up the foam by turning the Shampoo Tank to the OFF position.
Optional Accessories CLEANING THE CARPET SHAMPOO SYSTEM (cont) 4 Turn the Accessory Lock (22) to the left (counterclockwise). The Carpet Shampoo System Nozzle/Tray Assembly will tip forward. Lift the Nozzle/Tray Assembly off the Sentria™ system and carry it to the sink. > 5 Remove the hose from the tray and rinse. 6 By using the handle, turn the Belt Lifter to the right (clockwise) until the green arrows line up. Pull the tray and nozzle apart. Rinse tray.
Optional Accessories CLEANING THE CARPET SHAMPOO SYSTEM (cont) 8 To remove the Shampoo Tank from the Air Exhaust Port (19), rotate it away from the Sentria™ system as far as it will go, then lift it upwards. > 9 Remove and clean the Suds Screen Cap, Cup and Sponge Filter. Rinse out the Shampoo Tank with cold water and replace the Screen Cap, Cup and Sponge Filter. NOTE: The belt should not be stretched for extended periods. Make sure the green arrows on the nozzle line up for storage.
Optional Accessories REPLACING A WORN CARPET SHAMPOO SYSTEM NOZZLE BELT (cont) 3 Align the metal ends of the brush with the slots on the tray and push the brush in until it snaps into place. The brush will only fit the tray the correct way. NOTE: The belt should not be stretched when stored for an extended period. Make sure the green arrows line up for storage.
Optional Accessories PROTECTING YOUR CARPET (cont) 4 If Kirby Guard has been sprayed onto any hard surfaces such as furniture, baseboards, tile, etc., wipe off before drying occurs. Allow carpets to dry thoroughly before resuming normal use. > 5 Thoroughly clean the Portable Sprayer after use. • USING THE KIRBY MIRACLE WAXER® FLOOR POLISHER 1 To assemble the roller waxer applicator, attach the top half of the roller waxer handle to the bottom half (if not already done).
Optional Accessories USING THE MIRACLE WAXER® FLOOR POLISHER (cont) 2 With the wax roller bag facing the hooked end of the long roller handle, push the wax roller over the connector on the bottom of the handle until secure. > 3 Pull the roller bag off the wax roller and save the packing bag. Begin waxing according to the directions in box on previous page. > 4 To remove the wax roller from the long handle, hold the original wax roller packing bag with the open end facing the roller.
Optional Accessories FLOOR BUFFER SET-UP Your Sentria™ system can be used as an effective floor buffer for wood or tile floors. To use the Floor Buffer, you must first insert the Buffer Brush into the Floor Buffer Nozzle. 1 /!\ CAUTION: Center the belt of the Buffer Brush in the middle area between the tufts of the brush. > 2 Turn the Buffer Nozzle over and slide the ends of the Brush into the slots at each end of the nozzle. The Buffer Brush will only fit the correct way.
Optional Accessories FLOOR BUFFER SET-UP (cont) 5 Place the hooks located on the rear of the nozzle over the Attaching Bar (24) and push the nozzle up against the Sentria™ system. Turn the Accessory Lock (22) all the way to the right (clockwise) to lock the nozzle in place. > 6 To engage the drive belt and Buffer Brush, use the handle to turn the Belt Lifter all the way to the right (clockwise) until the green arrows line up. Lower the Headlight Hood (21).
Optional Accessories USING THE FLOOR BUFFER (cont) 9 Press the Toe-Touch Control Upper Pedal (8) to lower the brush one notch at a time. Lower the brush as far as the Toe-Touch Control will allow. With the Buffer running, move the Sentria™ system over the floor as though you were cleaning a carpet, using slow, steady strokes. NOTE: The belt should not be stretched when stored for an extended period. Make sure the green arrows line up for storage.
Optional Accessories USING THE CARPET FLUFFER (cont) 3 Lower the Carpet Fluffer Nozzle one notch at a time by pushing the Toe-Touch Control Upper Pedal (8). The instant the brush contacts the carpet, stop lowering the brush. > 4 Then engage Tech Drive® power assist by pressing down on the red "D" side of the "N/D" Pedal. You are now ready to fluff the carpet by pushing the cleaner back and forth over the carpet. NOTE: • Lowering the brush too far on cable yarn type carpets may cause the carpet to fuzz.
Optional Accessories TURBO-SANDING SET-UP (cont) 3 Select the correct grade of sandpaper needed for the job. Use fine paper for a smooth finish and coarse paper to clear rough surfaces or remove paint. Slide the sheet into the front clamp and lock the clamp lever. NOTE: Three grades of sandpaper come with the Sander. Each piece is a standard 1/3 sheet. > 4 Tightly wrap the paper around the bottom of the Turbo Accessory and tuck the end into the rear clamp. Lock the rear clamp.
Optional Accessories TURBO POLISHING Attach the synthetic lamb's wool pad using the same procedure as attaching sandpaper (see page 42). The Turbo Accessory now becomes a polisher. Use it for polishing hard waxed surfaces, such as table tops, paneling, and large flat surfaces. It can be used to polish cars. The Dust Shroud is not used when polishing. • TURBO SCOURING Attach the webbed nylon scouring pad using the same procedure as attaching sandpaper (see page 42).
Optional Accessories USING THE ZIPPBRUSH When attached to the Attachment Hose, the Zippbrush can be used for a wide variety of cleaning surfaces, including upholstery, and carpeted steps. It can be used to clean automotive interiors. For optimum results, do not press down heavily on the Zippbrush. Allow the brush to rotate at maximum speed by gently moving it side to side on the surface being cleaned.
Optional Accessories Handi-Butler® Tool Important Safety Instructions The Handi-Butler Model #298906 or #298806 is for use only with the Sentria™ (G10 series) system. Use only as described in this manual. Before using this accessory, read and follow the "Important Safety Instructions" and "Warnings" in the Sentria vacuum cleaner Owner's Manual in addition to the warnings noted below. WARNING - BE FAMILIAR WITH ALL THE IMPORTANT SAFETY INSTRUCTIONS BEFORE USING YOUR HAND-BUTLER TOOL.
Optional Accessories Specific Personal Safety Rules (cont.): • Always hold the tool firmly in your hands. • Secure Flexible Shaft or Rotator Shaft to the Handi-Butler tool before use. • Do not reach in the area of the spinning tool on the end of the Flexible Shaft or Rotator shaft. • Do not remove the Flexible Shaft or 6" Rotator Shaft while the unit is running. • Do not touch the spinning parts immediately after use because the tools or tip might be hot. • Do not force the Handi-Butler tool.
Optional Accessories FUNCTIONAL DESCRIPTION The Handi-Butler tool is an air-powered rotary tool that can be used for a wide variety of fine, detailed cleaning and polishing tasks. It can be used as a hand-held tool or as a stationary, table-top tool.
Optional Accessories USING THE HANDI-BUTLER TOOL IN THE HAND-HELD MODE The Handi-Butler Tool Hand-Held Mode gives the user maximum flexibility when cleaning and polishing an item. 1 To use the Handi-Butler tool in the hand-held mode, begin with the hose attached to the front of your Sentria™ system. > 2 For ease of use, attach the bit to the Flexible Shaft (B) before assembling the Handi-Butler tool.
Optional Accessories 4 Select one of the cleaning or polishing tools and insert into the tip of the Flexible Shaft (B). Firmly tighten the tip to secure the tool in place with the Mini Wrench (E) . Remove the Angled Key (D). > NOTE: The Angled Key (D) must be inserted into the holes in order to attach or remove a polishing or cleaning tool. 5 Now you are ready to attach the Handi-Butler tool to your Sentria™ system. Firmly twist the Handi-Butler tool (A) on to the end of the hose.
Optional Accessories USING THE HANDI-BUTLER TOOL IN THE TABLE-TOP MODE The Hand-Butler tool table-top mode allows you to hold the item you wish to polish or clean with two hands for better control. In the Table-Top mode, the cleaner should be securely fixed in the Handi-Butler Mounting Cradle (G) to prevent the cleaner from moving on the work surface. The cradle should be bolted (using the provided holes as shown using 1/4" or M6 bolts, washers and nuts) to a stable surface.
Optional Accessories 5 Now you are ready to attach a tool to the 6" Rotator Shaft. Rotate the tip of the Rotator Shaft (C) until the hole in the tip lines up with the hole in the grip section. Insert the long end of the Angled Key (D) into the holes. > 6 Use the enclosed Mini Wrench (E)to loosen the silver rotating tip at the end of the Rotator Shaft (C). > 7 Select one of the cleaning or polishing tools and insert into the tip of the Rotator Shaft (C).
Optional Accessories MAINTENANCE Kirby recommends that all tools be serviced by an authorized Kirby Distributor. The polishing tips and brushes in the Handi-Butler tool have been designed for many hours of use. Check them regularly for wear and replace when necessary. Only genuine Kirby ® Handi-Butler® tool parts should be used. 1 Oil the flexible shaft by dripping 3-4 drops of oil along the drive shaft after every ten uses.
Optional Accessories LOCKING OUT THE HANDI-BUTLER TOOL® When leaving the Handi-Butler tool in the table-top mode unattended, it is recommended that the user lock out the tool to prevent accidental starting or access to the tool by children. With the unit securely seated in the Mounting Cradle (G), insert the tines of the Lockout Bar (I) in to the slots at the base of the On-Off pedal of the Sentria unit. Then, slide the hole on the Lockout Bar over the eyelet on the Mounting Cradle.
Operating/Maintenance Tips CHANGING THE POWER NOZZLE BELT After extended use, the Power Nozzle Belt on your Sentria™ system may become stretched and worn causing the belt to slip.(See page 11 - Brush Roll Performance Indicator Light.) If this condition exists, simply replace the old belt with a new one. NOTE: Use only approved Kirby ® belts. To change the belt, remove the nozzle from the Sentria system.
Operating/Maintenance Tips CHANGING THE POWER NOZZLE BELT (cont) Make sure the Brash Roll Bristle Height Adjustment setting (1, 2, or 3) is the same on both ends as when the brush was removed. See below for discussion of the Brush Roll Bristle Height Adjustment (1, 2, or 3). Place the belt and Brush Roll back into the nozzle. One of the plastic Brush Roll ends is larger than the other, thus the Brush Roll will only fit in the nozzle one way. 5 Then center the belt on the Brush.
Operating/Maintenance Tips ADJUSTING THE BRUSH ROLL HEIGHT (cont) 1 Remove the Power Nozzle (25) from the Sentria system. > 2 Release the belt tension by using the handle on the Belt Lifter (20) to turn it all the way to the right (clockwise) until the green arrows line up. Unlock the two latches on the rear of the Power Nozzle to remove the Rug Plate (26). Then lift the brush out of the nozzle. > 3 Rotate the plastic Brash Roll ends to the 1,2 or 3-notch settings as desired.
Operating/Maintenance Tips Miscellaneous Parts Replacement WHEEL WEAR/ REPLACEMENT Kirby® wheels are made with a pliable tread that is designed to prevent carpet wear and prevent damage to non-carpeted floors. After extended periods of use, the tread on the wheels will wear out and the wheels will need to be replaced. Check wheel tread occasionally to determine if the wheels need to be replaced. The tread material is lighter in color than the plastic wheel itself.
Operating/Maintenance Tips Questions and Answers/Troubleshooting Q WHAT IS A DOUBLE-INSULATED MACHINE? (Servicing of double-insulated appliances) A In a double-insulated appliance, two systems of insulation are provided instead of grounding. No grounding means is necessary on a double-insulated appliance, nor should a means for grounding be added to the appliance. A double-insulated appliance is marked with the words "DOUBLE-INSULATED" (U.S.A. and Canada).
Operating/Maintenance Tips Questions and Answers/Trouble shooting Q I SMELL BURNING RUBBER WHEN I USE MY Sentria™ SYSTEM WHAT SHOULD I DO? A 1. Check to see if the Brash Roll is turning when the Sentria system is running. If not, then the Brush Roll may be stalled due to threads around the ends. Remove Brush Roll and make sure it rotates freely at both ends. (See page 54.) 2. The belt may not be fully engaged (or disengaged). Make sure the green arrows or red arrows on the Belt Lifter (20) match up fully.
Operating/Maintenance Tips Questions and Answers/Troubleshooting Q HOW DO I VACUUM MY UPHOLSTERED FURNITURE? A 1. Convert to a canister. (See page 19.) (Do not use Power Nozzle (25) on furniture.) 2. Use the Attachment Hose with or without the following attachments: • the Upholstery Nozzle. • the Crevice Tool with the brush removed. (Use in between seat cushions and in crevices.) • the optional Zippbrush.
Operating/Maintenance Tips Questions and Answers/Troubleshooting Q HOW DO I CLEAN OTHER HOME FURNISHINGS? A Books and Bookcases: 1. Convert to a canister. (See page 19.) 2. Attach the Duster Brush to the end of the Attachment Hose and "dust" the books and bookcase. 3. Other options include using an Extension Tube with the Duster Brash or the Wall & Ceiling Brush to dust the bookcase top. Lampshades and Pictures: 1. Convert to a canister. (See page 19.) 2.
Consumer Relations Got a Question? Need Assistance? Your local authorized distributorship is available to answer any questions regarding your purchase or the operation of your Sentria™ Home Care System. The Kirby Company also has Consumer Relations Specialists available to answer any questions you may have about the Sentria Home Care System or provide you with the name of your nearest Kirby distributor. You can contact USA Consumer Relations by: e-mail consumer@kirbywhq.
Kirby® Home Care Products From Your Factory Authorized Distributors and Service Centers ALLERGEN CONTROL PRODUCTS MicroAllergen Filter Bags Traps 99.97% of particles as small as 0.3 microns. Rated HEPA 11. Minimizes bag odor. Allergen Control Shampoo Neutralizes dust mite particles. Reduces allergens caused by pollen. Cleans and brightens carpets. Kirby Guard Carpet & Upholstery Protector Minimizes dirt penetration to keep carpets cleaner, longer. Helps to keep spills from seeping in.
Kirby® Home Care Products From Your Factory Authorized Distributors and Service Centers HARD SURFACE PRODUCT FAMILY Scuttle® Glass & Surface Cleaner A traditional Kirby favorite; great for hard surfaces such as countertops, appliances as well as windows, mirrors and more. Dries to a streak-free shine. Citrus Scuttle Heavy-duty cleaner for all types of indoor and outdoor surfaces. Great for ovens, grills, machinery and work areas.
Index E A About this Manual Accessories Accessory Lock Air Intake Guard Attaching Bar Attachments Attachment Hose Crevice Tool Duster Brush Extension Tubes Inflator/Deflator Massage Cup Suction Control Grip Surface Nozzle Upholstery Nozzle Wall & Ceiling Brush 4 29 19 23 19 18 19 21 20 20 24 22 22 20 21 21 B Bag Assembly-removal Bag Release Button Bag Support Strap Changing Bags Disposable Filter Bags . . . . Outer Permanent Bag . . . .
C€ DECLARATION OF CONFORMITY We, Kirby, declare under our sole responsibility that, where applicable, the Kirby Model G10E Vacuum Cleaner is in conformity with the following standards or standardized documents.
Sentria™ No.
Accessories and Attachments No. Part Recommended Uses 30 Kaddy Storage of accessories. 31 Portable Sprayer Attach onto attachment hose with unit in blower mode only to apply water-based, non-flammable liquids. 32 Portable Handle To transform unit from upright to portable position by removing upright handle and inserting portable handle. Aids in cleaning of carpeted stairs and mattress cleaning.
IMPORTANT The following information need only apply when changing plugs on Sentria™ models that are used in the U.K., Australia, South Africa and New Zealand.