User Manual

ManualsBrandsKitchenAid ManualsBlendersMagnetic Drive Blender Candy Apple Red

5KSB5080A

5KSB5085A

INSTRUCTIONS

W10729916B_EN_v03.indd 1 3/20/15 3:13 PM

Summary of content (16 pages)

PAGE 1
5KSB5080A 5KSB5085A INSTRUCTIONS W10729916B_EN_v03.
PAGE 2
BLENDER BLENDERINSTRUCTIONS INSTRUCTIONS B TABLE OF CONTENTS BLENDER SAFETY Important safeguards........................................................................................... 3 Electrical requirements....................................................................................... 5 Electrical equipment waste disposal.................................................................... 5 Motor horsepower.....................................................................................
PAGE 3
English BLENDER SAFETY IMPORTANT SAFEGUARDS When using electrical appliances, basic safety precautions should always be followed, including the following: 1. Read all instructions. Misuse of appliance may result in personal injury. 2. To protect against risk of electrical shock, do not put Blender in water or other liquid. 3.
PAGE 4
BLENDER SAFETY B 6. Do not operate the Blender with a damaged cord or plug or after appliance malfunctions, or is dropped or damaged in any manner. Return appliance to the nearest Authorised Service Center for examination, repair or electrical or mechanical adjustment, in order to avoid a hazard. 7. Do not use outdoors. 8. Do not let cord hang over edge of table or counter. 9. Keep hands and utensils out of container while blending to reduce the risk of severe injury to persons or damage to the Blender.
PAGE 5
BLENDER SAFETY Electrical requirements Frequency: 50/60 Hz Wattage : 1300 watts NOTE: If the plug does not fit in the outlet, contact a qualified electrician. Do not modify the plug in any way. Do not use an adapter. English Voltage: 220-240 volts Do not use an extension cord. If the power supply cord is too short, have a qualified electrician or serviceman install an outlet near the appliance.
PAGE 6
PARTS AND FEATURES A Parts and accessories Removable ingredient cap with measuring markings Removable funnel Function selection dial* BPA Free pitcher with lid Die-cast metal base O Stainless steel blades Pitcher release lever Magnetic drive (not visible) * See the “Blender function guide” section. 6 W10729916B_EN_v03.
PAGE 7
ASSEMBLING THE BLENDER Preparing the Blender for use Before using your Blender for the first time, wipe Blender base with a warm damp cloth, then wipe clean with a damp cloth. Dry with a soft cloth. Wash pitcher, lid, and ingredient cup in warm, sudsy water (see “Care and cleaning” section). Rinse parts and wipe dry. English Before first use Before using the Blender, plug into a grounded outlet.
PAGE 8
OPERATING THE BLENDER 1 Remove the pitcher from the Blender base in order to fill it with ingredients. Pull the pitcher release lever to help remove the pitcher. Grab the handle firmly, and pull the pitcher straight towards you to remove. O 2 Put ingredients in the pitcher. Add liquids first, then soft foods, then ice or frozen fruit last. Do not fill the pitcher beyond the max fill line - especially when using primarily liquids.
PAGE 9
English OPERATING THE BLENDER 5 Turn the selection knob to your desired pre-set program or variable speed selection (see the “Blender function guide” for more information). 6 Press the START/PAUSE button. 7 You may use the removable ingredient cap and removable funnel to add more ingredients to the pitcher while blending, if needed. The cap includes convenient measuring indicators for precise measurement of added ingredients.
PAGE 10
OPERATING THE BLENDER T Blender function guide The four pre-set recipe programs were each developed based on typical recipes in that category. However, you’ll find that not all recipes are exactly the same, and sometimes a particular recipe might blend more to your preference on a program that is not obvious. For example, some milkshakes with frozen fruit blend better on the Icy Drinks/Smoothies program. Also, when making smoothies, you might prefer the finer texture that the Juice program creates.
PAGE 11
TIPS FOR GREAT RESULTS Using the Blender • Stop the Blender before using utensils in the pitcher. Use a rubber spatula to mix ingredients only when the Blender is off. Never use any utensil, including spatulas, in the pitcher while the motor is running. • The Blender is capable of handling hot ingredients. Cool hot foods, if possible, before blending. • The Blender is not intended to be used as a heating device.
PAGE 12
TIPS FOR GREAT RESULTS C How to... Dissolve flavoured gelatin: Pour boiling water into the pitcher; add gelatin. Remove centre ingredient cup, and place a towel over the lid. Use the variable speeds setting and blend at a slow speed until gelatin is dissolved, about 10 to 30 seconds. Add other ingredients. Chop fruits and vegetables: Put 2 cups (475 mL) of fruit or vegetable chunks in pitcher.
PAGE 13
CARE AND CLEANING Cleaning the Blender 1 To clean the Blender base and cord: Unplug the Blender before cleaning. Wipe with a warm, damp cloth; wipe clean with a damp cloth, and dry with a soft cloth. Make sure to clean inside the ingredient feed each time. 3 To clean pitcher, lid, ingredient cap, and funnel: Wash all items in the dishwasher on the top or bottom rack. Or hand wash with soapy water, rinse, and wipe dry. 2 English • Clean the Blender thoroughly after every use.
PAGE 14
TROUBLESHOOTING T Understanding the Blender flash codes IMPORTANT: The Blender will not operate at any speed unless the START/PAUSE button is pressed first. LED is flashing slowly LED is flashing rapidly LED is not flashing Ready mode If the LED slowly glows with increasing intensity and then is off, the Blender is ready for blending. Press START/PAUSE button to start blending. Error mode If the LED flashes on/off in rapid bursts, the Blender is not ready for blending.
PAGE 15
TROUBLESHOOTING • If the LED is flashing on/off in rapid bursts, the pitcher might not be fully in place or the Blender might have gone into “sleep mode” and need to be reset to “OFF/O”. Follow the “Error mode” instructions. • Check to see if the Blender is plugged into a grounded outlet. If it is, press START/PAUSE; then unplug the Blender. Plug it back in to the same outlet, and press START/PAUSE.