® TILT-HEAD STAND MIXERS MIXER INSTRUCTIONS / Model 5K45SS Mode[ 5KSM150PS
Table of Contents Important Safeguards ........................................................................................ 1 Electrical Requirements ...................................................................................... 2 5K45SS Tilt-Head Stand Mixer Features ............................................................. 3 5KSM1 50PS Tilt-Head Stand Mixer Features ...................................................... 4 Assembling Your Tilt-Head Stand Mixer ......................
IMPORTANT SAFEGUARDS When using electrical appliances, basic safety precautions should always be followed including the following: 1. Read all instructions. 2. To protect against risk of electrical shock, do not put Stand Mixer in water or other liquid. 3. Close supervision is necessary when any appliance is used by or near children. 4. Unplug Stand Mixer from outlet when not in use, before putting on or taking off parts and before cleaning. 5. Avoid contacting moving parts.
Electrical Requirements Your Stand Mixer operates on a regular 220-240 volt A.C., 50/60 hertz house current. The wattage rating for your Stand Mixer is printed on the trim band. This wattage is determined by using the attachment which draws the greatest power. Other recommended attachments may draw significantly less power. Do not use an extension cord. If the power supply cord is too short, have a qualified electrician or serviceman install an outlet near the appliance.
K45SS Tilt-Head Stand Mixer Features Attachment Motor Head Hub Attachment Knob Motor __ Control Speed Lever Beater _, , Height , . : i_ Head Locking Lever (not shown) Beater Shaft -- Adjustment Screw Flat Beater G 4,25 liter (4.
5KSM150PS Tilt-Head Stand Mixer Features Attachment Motor Head Hub Attachment Knob Speed Control Lever Beater Height Adjustment Screw "_" , *_ 0 Pouring Shield 4,8 miter (5 qrt) stainmess steem bowl Wire Whip Bowl Clamping Dough Hook Plate
Assembling Your Tilt-Head Stand Mixer To Remove Flat Beater, Wire Whip, or Dough Nook To Attach Bowl 1. Turn speed control to "0". 2. Unplug stand mixer or disconnect power. 3. Hold the locking lever in the UNLOCK position and tilt motor head back. 4. Place bowl on bowl clamping plate. 5. Turn bowl gently in clockwise direction. To Remove Bowl 1. Turn speed control to "0". 2. Unplug stand mixer or disconnect power. 3. Hold the locking lever in the UNLOCK position and tilt motor head back. 4.
Assembling Your Pouring Shield* Insert the tabs on the front half of the shield (with the chute) under the tab openings on the back half of the shield, then lower the shield to lock into place. . i \ Pouring Chute To Attach Pouring Shield 1. Turn speed control to "0". 2. Unplug stand mixer or disconnect power. 3. Attach flat beater, dough hook or wire whip and bowl. See page 5. 4. Place the back half of the shield (without the chute) on rim of the bowl. To Remove Pouring Shield 1.
Beater to Bowl Clearance Your Stand Mixer is adjusted at the factory so the flat beater just clears the bottom of the bowl. If, for any reason, the flat beater hits the bottom of the bowl or is too far away from the bowl, you can correct clearance easily. 1. Turn speed control to "0". 2. Unplug stand mixer or disconnect power. 3. Lift motor head. 4. Turn screw (A) SLIGHTLYcounter clockwise (left) to raise flat beater or clockwise (right) to lower flat beater. 5.
Care and Cleaning Bowl, white flat beater and white dough hook may be washed in an automatic dishwasher. Or, clean them thoroughly in hot sudsy water and rinse completely before drying. Do not store beaters on shaft. Planetary During operation, the flat beater moves around the stationary bowl, at the same time turning in the opposite direction on its own axis. The diagram shows the Stand Injury Hazard Unplug mixer before touching beaters.
Speed Control Guide - 10 Speed Mixers All speeds have the Soft Start feature which automatically starts the Stand Mixer at a lower speed to help prevent ingredient splash-out and "flour puff" at startup then quickly increases to the selected speed for optimal oerformance. Number of Speed Stir Speed 10 STIR For slow stirring, combining, mashing, starting all mixing procedures. Use to add flour and dry ingredients to batter, and add liquids to dry ingredients.
Mixing Tips Cake Mixes Converting Your Recipe for the Stand Mixer When preparing packaged cake mixes, use Speed 4 for medium speed and Speed 6 for high speed. For best results, mix for the time stated on the package directions. The mixing instructions found in this book can be used to convert your favorite recipes for use with your KitchenAid _:Stand Mixer. To help determine a mixing procedure, your own observations and experience will be needed.
Mixing and Kneading "Rapid Mix" describes a bread baking method that calls for dry yeast to be mixed with other dry ingredients before liquid is added. In contrast, the traditional method is to dissolve yeast in warm water. 1. Place all dry ingredients including yeast into bowl, except last 125 to 250 gr (1 to 2 cups) flour. 2. Attach bowl and dough hook. Lock mixer head. Turn to Speed 2 and mix about 15 seconds, or until ingredients are combined. Yeast Dough 5.
Egg Whites Placeroom temperature egg whites in clean, dry bowl. Attach bowl and wire whip. To avoid splashing, gradually turn to designated speed and whip to desired stage. Seechart below. AMOUNT Begins to Hold Shape Air bubbles are fine and compact; product is white. Soft Peak SPEED Tips of peaks fall over when wire whip is removed. 1 egg white ....... GRADUALLYto 10 2-4 egg whites ........ GRADUALLYto 8 6 or more egg whites ........
Attachments General and Accessories Information KitchenAid _'Attachments are designed to assure long life. The attachment power shaft and hub socket are of a square design, to eliminate any possibility of slipping during the transmission of power to the attachment. The hub and shaft housing are tapered to assure a snug fit, even after prolonged use and wear. KitchenAid '_'Attachments require no extra power unit to operate them; the power unit is built-in.
When You Need Service If your Stand Mixer should malfunction or fail to operate, please check the following: Electrical - Is the Stand Mixer plugged in? - Is the fuse in the circuit to the Stand Mixer in working order? If you have a circuit breaker box, be sure the circuit is closed. - Turn the Stand Mixer off for 10-15 seconds, then turn it back on. If the mixer still does not start, allow it to cool for 30 minutes before turning it back on.
Household KitchenAid ® Tilt-Head Stand Mixer Warranty Length of Warranty: KitchenAid Will Pay For: KitchenAid Will Not Pay For: Europe, Australia and New Zealand: For the Artisan _'mixer 5KSM150PS: Five years Full Warranty from date of purchase. Replacement parts and repair labor costs to correct defects in materials or workmanship. Service must be provided by an Authorized KitchenAid Service Center A. Repairs when Stand Mixer is used for operations other than normal household food preparation.
Customer In U.K. & Ireland: Address: Service Tollfree number 00800 38104026 KitchenAid Europa, Inc. PO BOX 19 B-201 8 ANTWERP 11 BELGIUM www.KitchenAid.com FOR THE WAY IT'S MADE. TM @Registered Trademark of KitchenAid, U.S.A. 'Trademark of KitchenAid, U.S.A. The shape of the stand mixer is a trademark of KitchenAid, U.S.A. ,_c;2005. All rights reserved. Specifications subject to change without 9709309 notice.
