STAND MIXER BATEDEIRA DOMÉSTICA W10544160C_v04.
Table of Contents Important Safeguards..............................................................................................3 Electrical Requirements for Brazil Only...................................................................6 About Your Mixer Tilt Head Mixer Features......................................................................................7 Bowl Lift Mixer Features......................................................................................
English Tilt Head Mixer Features Attachment Hub Motor Head Attachment Knob Motor Head Locking Lever (not shown) Speed Control Lever Beater Shaft IMPORTANT SAFEGUARDS When using electrical appliances, basic safety Flat Beater precautions should always be followed, including the following: 1. Read all instructions. Misuse of appliance may result in personal injury. 2. To protect against risk of electrical shock, do not put Food Processor in water or other liquid. 3.
7. Do not operate mixer unattended or near edge of work surface. When used for heavy loads or at high speeds, mixer may move on work surface. 8. Remove flat beater, wire whip, or dough hook from mixer before washing. 9. Do no operate any appliance with a damaged cord set or after the appliance has been dropped or damaged in any manner. If the supply cord is damaged, it must be replaced by the manufacturer, its service agent or similarly qualified persons in order to avoid a hazard. 10.
English Tilt Head Mixer Features 19. ELECTRICAL REQUIREMENTS: Your KitchenAid mixer operates on a regular 220-240 volt A.C., 50-60 hertz house current. The wattage rating for your KitchenAid Mixer is printed on the trim band. This wattage is determined by using the attachment that draws the Attachment Hub greatest power. Other recommended attachments may draw significantly less power. Motor Head Attachment Knob 20.
W10544160C_v04.
English English Tilt Head Head Mixer Mixer Features Features Tilt Attachment Hub Hub Attachment Motor Head Head Motor Attachment Knob Knob Attachment Motor Head Head Motor Locking Lever Lever Locking (not shown) shown) (not Speed Speed Control Control Lever Lever Beater Shaft Shaft Beater Flat Beater Beater Flat R-5 R-5 Wire Whip Whip Wire Dough Hook Hook Dough 55 W10544160C_v04.indd 7 4.8 LL (5 (5 Qt) Qt) 4.
0 12 8 10 4 6 d , USA enAi igan tch Mich ph, KiJose St. OFF ON TO LOCK MOTOR HEAD IN RAISED POSITION • Push locking lever into UNLOCK position and hold. • Tilt motor head back. • Move locking lever into LOCK position. TO ATTACH BOWL • Be sure speed control is OFF. • Tilt motor head back. • Place bowl on bowl-clamping plate. • Turn bowl gently in clockwise direction (see picture above). • Sit pouring shield on bowl.* * If Pouring Shield is included TO REMOVE BOWL • Turn speed control to OFF.
Tilt Head Bowl Lift Mixer Features English Motor Head AttachmentAttachment Hub Hub Motor Head Attachment Attachment Knob Knob Speed Control Lever BowlHead Lift Handle Motor (not shown) Locking Lever (not shown) Speed Spring Latch and Control Bowl Pin (notLever shown) Locating Pins Beater Shaft Beater Shaft Bowl Support Wire Whip Flat Beater Flat Beater Dough Hook R-5 Wire Whip Dough Hook 75 W10544160C_v04.indd 9 4.8 L (5 Qt) Stainless 4.
TO ATTACH BOWL • Be sure speed control is OFF. • Place bowl lift handle in down position. • Fit bowl supports over locating pins. • Press down on back of bowl until bowl pin snaps into spring latch. • Sit pouring shield* on bowl. • Raise bowl before mixing. TO RAISE BOWL • Rotate handle back and up until it snaps into the locked vertical position. • Bowl must always be in raised, locked position when mixing. TO ATTACH POURING SHIELD* 1. Turn speed control to OFF. 2. Unplug Stand Mixer or disconnect power.
Using YourMixer KitchenAid Tilt Head FeaturesAttachments See the Stand Mixer Attachments Use and Care Guide for speed settings and operating times.
Planetary Mixing Action Your KitchenAid Mixer will mix faster and more thoroughly than most other electric mixers. Therefore, the mixing time in most recipes must be adjusted to avoid overbeating. During operation, the flat beater moves around the stationary bowl, at the same time turning in the opposite direction on its own axis. The diagram shows the complete coverage of the bowl made by the path of the beater.
Mixing Tips Tilt Head Mixer Features Converting Your Recipe to the Mixer The mixing instructions found in this book can be used to convert your favorite recipes for use with your KitchenAid Mixer. To help determine a mixing procedure, your own observations and experience will be needed. Watch the batter or dough and mix only until it has the desired appearance described in your recipe,Motor such asHead “smooth and creamy.” Use the “Speed Control Guide” to help determine proper mixing speeds.
6. Unlock and raise Tilt Head or lower bowl on Bowl Lift and remove dough from hook. 5. When dough clings to hook, knead on Speed 2 for 2 minutes or until dough is smooth and elastic. NOTE: These instructions illustrate bread making with the Rapid Mix method. When using the conventional method, dissolve yeast in warm water in warmed bowl. Add remaining liquids and dry ingredients – except last 250 mL to 500 mL flour. Turn to Speed 2 for about 1 minute, or until ingredients are thoroughly mixed.
Before YouMixer Call For Service Tilt Head Features Please read the following before calling your service center. 1. The mixer may warm up during use. Under heavy loads with extended mixing time periods, you may not be able to comfortably touch the top of the unit. This is normal. 2. The mixer may emit a pungent odor, Motor Head with especially when new. This is common electric motors. 3. If flat beater strikes bowl, stop the mixer. See “Beater-to-Bowl Clearance.” English 3.
© 2015. All rights reserved. © 2015. Todos os direitos reservados. W10544160C W10544160C_v04.
