5KSM125, 5KSM175PS 5K45SS, 5KSM45
ENGLISH TABLE OF CONTENTS PARTS AND FEATURES.........................................................................................6 Parts and accessories......................................................................................6 STAND MIXER SAFETY .........................................................................................7 Important safeguards .....................................................................................7 Electrical requirements .........................
PARTS AND FEATURES PARTS AND ACCESSORIES Attachment hub Attachment knob Motor head Speed control lever Pouring shield* Motor head locking lever (not shown) Beater shaft 3 L stainless steel bowl* Beater height adjustment screw (not shown) Dough hook Bowl** Bowl clamping plate Flat beater Flex Edge beater* Wire whip * Included with select models only. Also available as optional accessory. ** The bowl design and material depend on the Stand Mixer model.
ENGLISH STAND MIXER SAFETY IMPORTANT SAFEGUARDS When using electrical appliances, basic safety precautions should always be followed, including the following: 1. Read all instructions. 2. To protect against risk of electrical shock, do not put Stand Mixer in water or other liquid. 3. Unplug Stand Mixer from outlet when not in use, before putting on or taking off parts, and before cleaning. 4. Never leave the Stand Mixer unattended while it is in operation.
STAND MIXER SAFETY 5. This appliance can be used by children aged from 8 years and above and persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning use of the appliance in a safe way and understand hazards involved. Children shall not play with the appliance. Cleaning and user maintenance shall not be made by children without supervision. 6. Avoid contacting moving parts.
ELECTRICAL REQUIREMENTS WARNING Wattage: 300 Watts for models 5KSM125 and 5KSM175PS 275 Watts for models 5K45SS and 5KSM45 Voltage: 220-240 V Hertz: 50-60 Hz Electrical Shock Hazard Plug into an earthed outlet. Do not remove earth prong. Do not use an adapter. Do not use an extension cord. NOTE: If the plug does not fit in the outlet, contact a qualified electrician. Do not modify the plug in any way. Do not use an adapter. Do not use an extension cord.
USING THE STAND MIXER SPEED CONTROL GUIDE All speeds have the Soft Start feature which automatically starts the Stand Mixer at a lower speed to help avoid ingredient splash-out and “flour puff” at start-up, then quickly increases to the selected speed for optimal performance. SPEED ACTION ATTACHMENT DESCRIPTION 1 STIR For slow stirring, combining, mashing, starting all mixing procedures. Use to add flour and dry ingredients to batter, and to add liquids to dry ingredients.
ENGLISH USING THE STAND MIXER ACCESSORY GUIDE ACCESSORY USES Flat beater and Flex Edge beater* for normal to heavy mixtures: Cakes, creamed frostings, candies, cookies, pie pastry, biscuits, meat loaf, mashed potatoes Wire whip for mixtures that need air incorporated: Eggs, egg whites, heavy cream, boiled frostings, sponge cakes, mayonnaise, some candies Dough hook for mixing and kneading yeast doughs: Breads, rolls, pizza dough, buns * Included with select models only.
USING THE STAND MIXER LIFTING/LOWERING THE MOTOR HEAD 1 To lift motor head: Push the locking lever to the UNLOCK position and lift the head. Once lifted, the lever will automatically go back in LOCK position to keep the head lifted. 2 To put down motor head: Push the locking lever to UNLOCK and gently bring the head down. The locking lever will automatically go back in LOCK position when the head is down. Before mixing, test lock by attempting to raise motor head.
2 Hold the locking lever in the UNLOCK position and tilt motor head back. 4 To remove accessory: Repeat steps 1 and 2. Press accessory upward as far as possible and turn to the left. Then pull accessory from the beater shaft. 3 ENGLISH USING THE STAND MIXER Slip accessory onto beater shaft and press upward as far as possible. Then, turn accessory to the right, hooking accessory over the pin on the shaft.
USING THE STAND MIXER BEATER TO BOWL CLEARANCE Your Stand Mixer is adjusted at the factory so the flat beater just clears the bottom of the bowl. If, for any reason, the flat beater hits the bottom of the bowl or is too far away from the bowl, you can correct clearance easily. 1 Turn speed control to “0”. Unplug Stand Mixer. 2 Lift motor head. Turn screw slightly counterclockwise (left) to raise flat beater or clockwise (right) to lower flat beater.
3 To remove pouring shield: Turn speed control to “0”. Unplug Stand Mixer. 4 ENGLISH USING THE STAND MIXER Lift the front of the pouring shield clear of the bowl rim and pull forward. Remove attachment and bowl. USING THE POURING SHIELD* Use the pouring shield to avoid having ingredients splashing out of the bowl when mixing, as well as to easily pour ingredients in the bowl while mixing. 1 For best results, rotate the shield so the motor head covers the U-shaped gap in the shield.
USING THE STAND MIXER OPERATING THE SPEED CONTROL NOTE: The Stand Mixer may warm up during use. Under heavy loads with extended mixing time, the top of the unit may become hot. This is normal. 1 Plug Stand Mixer into proper electrical outlet. Always set speed control lever on lowest speed to start, then gradually increase speed to avoid splashing ingredients. See “Speed control guide” chart. 2 Do not scrape bowl while Stand Mixer is operating.
ENGLISH USING THE STAND MIXER 3 Insert attachment shaft housing into attachment hub, making certain that attachment power shaft fits into square attachment hub socket. It may be necessary to rotate attachment back and forth. When attachment is in proper position, the pin on the attachment will fit into the notch on the hub rim. 4 Tighten attachment knob by turning clockwise until attachment is completely secured to Stand Mixer. 5 Plug into proper electrical outlet.
USING THE STAND MIXER 7 Loosen attachment knob by turning it counterclockwise. Rotate attachment slightly back and forth while pulling out. 8 Replace attachment hub cover. Tighten attachment knob by turning it clockwise. NOTE: See the Use and Care Guide of each specific attachment for recommended speed settings and operating times. TIPS FOR GREAT RESULTS EGG WHITES Place room temperature egg whites in clean, dry bowl. Attach bowl and wire whip.
MIXING TIPS Mixing time Your KitchenAid Stand Mixer will mix faster and more thoroughly than most other electric mixers. Therefore, the mixing time in most recipes must be adjusted to avoid over beating. To help determine the ideal mixing time, observe the batter or dough and mix only until it has the desired appearance described in your recipe, such as “smooth and creamy.” To select the best mixing speeds, use the “Speed control guide” section.
CARE AND CLEANING WARNING Electrical Shock Hazard Plug into an earthed outlet. 1 Always be sure to unplug Stand Mixer before cleaning. Wipe Stand Mixer with a soft, damp cloth. Do not use household/commercial cleaners. Wipe off beater shaft frequently, removing any residue that may accumulate. Do not immerse in water. 3 IMPORTANT: The wire whip is not dishwasher-safe. Clean it thoroughly in hot sudsy water and rinse completely before drying. Do not store wire whip on shaft. Do not remove earth prong.
WARNING Electrical Shock Hazard Plug into an earthed outlet. Do not remove earth prong. Do not use an adapter. Do not use an extension cord. Failure to follow these instructions can result in death, fire, or electrical shock. Please read the following before calling your service centre. 1. The Stand Mixer may warm up during use. Under heavy loads with extended mixing time periods, you may not be able to comfortably touch the top of the unit. This is normal. 2.
WARRANTY AND SERVICE KITCHENAID STAND MIXER WARRANTY Length of Warranty: KitchenAid Will Pay For: KitchenAid Will Not Pay For: Europe, Middle East and Africa: For Artisan models 5KSM125 and 5KSM175PS: five years full warranty from date of purchase. The replacement parts and repair labour costs to correct defects in materials or workmanship. Service must be provided by an Authorised KitchenAid Service Centre. A.
