Cooktop User Manual

3
Product Dimensions Cutout Dimensions
Clearance Dimensions
21-13/16"
(54.4 cm)
depth
14-5/8" (37.1 cm)
blower housing
depth
3-ft. (91.4 cm) long
power supply cable
factory installed.
2-15/16"
(74.6 mm)
burner box
depth
Side clearance — 6" (15.2 cm) minimum clearance between side
of cooktop and side wall is recommended for maximum
ventilation performance.
Rear clearance — 3/4" (19.1 mm) clearance between rear edge of
cooktop and rear wall is recommended.
Motor/blower clearance — 2" (51 mm) minimum clearance
between motor and cabinet is required for proper cooling.
6" (15.2 cm) clearance is recommended for servicing access.
Note: 24" (61 cm) minimum when bottom of wood or metal cabinet is
protected by not less than 1/4" (6.4 mm) flame retardant millboard covered
with not less than No. 28 MSG sheet steel, 0.015" (0.4 mm) stainless steel,
0.024" (0.6 mm) aluminum or 0.020" (0.5 mm) copper.
30" (76.2 cm) minimum clearance between the top of the cooking platform
and bottom of unprotected wood or sheet metal.
**
21" (53.3 cm)
opening depth
See Note ** for
minimum clearances
Do Not seal
cooktop to countertop.
Minimum distance
to nearest combustible
vertical surface
extending 18" (45.7 cm)
above cooktop
Cutout preparation:
Decorative laminate —
Chamfer all exposed edges to
prevent chipping laminate.
Cut radius corners and file to
smooth edges and to prevent
cracking.
2" (5.1 cm) minimum
space to front edge of
countertop
Install rear
wall junction
box in shaded
area. Darker
shaded area is
preferred.
Select required duct cutout
(see Page 4 for exhaust duct
cutout location).
Countertop must be
supported within
3" (7.6 cm) of cutout.
21" (53.3 cm)
cutout depth
Minimum base cabinet dimensions —
30" (76.2 cm) base cabinet width
24" (61 cm) base cabinet depth
25" (63.5 cm) countertop depth
Countertop opening dimensions that are shown must
be used. Given dimensions are minimum clearances and
provide required 0" (0 cm) clearance.
New installations — Follow minimum dimensions given.
5" (12.7 cm)
17"
(43.2 cm)
11" (27.9 cm)
8" (20.3 cm)
countertop
floor
Replacement installation — Be sure that front edge of
cooktop is at least 1-1/2" (38.1 mm) back from front
edge of countertop.
If cabinet has drawers, drawers will need to be
removed and drawer fronts installed on front of cabinet.
29-1/2" (74.9 cm) - 30" (76.2 cm) cooktop
35-1/2" (90.2 cm) - 36" (91.4 cm) cooktop
cutout width
29-1/2" (74.9 cm) - 30" (76.2 cm) cooktop
35-1/2" (90.2 cm) - 36" (91.4 cm) cooktop
cutout width
30" (76.2 cm) min - 30" (76.2 cm) cooktop
36" (91.4 cm) min - 36" (91.4 cm) cooktop
when higher than 18" (45.7 cm)
31-1/2" (80 cm) - 30" (76.2 cm) cooktop
37-1/2" (95.3 cm) - 36" (91.4 cm) cooktop
width
1" (25.4 mm)