® STAND MIXER INSTRUCTIONS BATIDORA CON BASE INSTRUCCIONES BATEDEIRA STAND MIXER INSTRUÇÕES W10399721A KitchenAid.
Table of Contents English Important Safety Instructions ..........................................................................................3 About Your Mixer Tilt Head Mixer Features..........................................................................................4, 5 Bowl Lift Mixer Features..........................................................................................6, 7 Using Your KitchenAid® Attachments ........................................................................
Important Safety Instructions When reading the Instructions Manual… Pay special attention to sections marked by the following words: wCAUTION These help you avoid damage to the product and/or other property. “NOTE” or “IMPORTANT” These sections give you helpful tips on using the product. wWARNING These help you avoid accidents that could lead to injury for someone using the product incorrectly. head, the head must be completely down 1. Read all instructions. before locking. Before mixing, make sure 2.
Tilt Head Mixer Features Attachment Hub Motor Head Attachment Knob English Motor Head Locking Lever (not shown) Beater Shaft Speed Control Lever Flat Beater R-4 4.
0 12 8 10 4 6 d , USA enAi igan tch Mich ph, KiJose St. ON TO LOCK MOTOR HEAD IN RAISED POSITION • Push locking lever up into UNLOCK position and hold. • Tilt motor head back. • Move locking lever into LOCK position. TO ATTACH BOWL • Be sure speed control is OFF. • Tilt motor head back. • Place bowl on bowl-clamping plate. • Turn bowl gently in clockwise direction (see picture above). • Sit pouring shield on bowl.
Bowl Lift Mixer Features Motor Head Attachment Hub English Attachment Knob Speed Control Lever Bowl Lift Handle (not shown) Spring Latch and Bowl Pin (not shown) Locating Pins Beater Shaft Bowl Support Flat Beater Wire Whip Dough Hook 4.
TO RAISE BOWL • Rotate handle back and up until it snaps into the locked vertical position. • Bowl must always be in raised, locked position when mixing. TO ATTACH POURING SHIELD* 1. Turn speed control to OFF. 2. Unplug Stand Mixer or disconnect power. 3. Attach Flat Beater, Dough Hook, or Wire Whip and bowl. 4. From the front of the mixer, slide the Pouring Shield over the bowl until the shield is centered. The bottom rim of the shield should fit within the bowl.
Using Your KitchenAid® Attachments See the Stand Mixer Attachments Use and Care Guide for speed settings and operating times.
Planetary Mixing Action Your KitchenAid® Mixer will mix faster and more thoroughly than most other electric mixers. Therefore, the mixing time in most recipes must be adjusted to avoid overbeating. English During operation, the flat beater moves around the stationary bowl, at the same time turning in the opposite direction on its own axis. The diagram shows the complete coverage of the bowl made by the path of the beater.
Mixing Tips English Converting Your Recipe to the Mixer The mixing instructions found in this book can be used to convert your favorite recipes for use with your KitchenAid® Mixer. To help determine a mixing procedure, your own observations and experience will be needed. Watch the batter or dough and mix only until it has the desired appearance described in your recipe, such as “smooth and creamy.” Use the “Speed Control Guide” to help determine proper mixing speeds.
5. When dough clings to hook, knead on Speed 2 for 2 minutes or until dough is smooth and elastic. NOTE: These instructions illustrate bread making with the Rapid Mix method. When using the conventional method, dissolve yeast in warm water in warmed bowl. Add remaining liquids and dry ingredients – except last 250 mL to 500 mL flour. Turn to Speed 2 for about 1 minute, or until ingredients are thoroughly mixed. Proceed with steps 4 through 6. Egg Whites Tips of peaks fall over when wire whip is removed.
Before You Call For Service English 3. Are the bowl and pouring shield* properly in place? 4. Model 5KPM50 is equipped with an overload device. If the mixer is overloaded, the Overload Reset Button will pop out and the mixer will shut off (see page 7). Turn the Speed Control Lever to OFF. Wait a few minutes, then push in the Overload Reset Button. Turn the Speed Control Lever to the desired speed and continue mixing. Please read the following before calling your service center. 1.