Performance Data Sheet
2
Linuron 140 ± 20%
20 ng/L
>97.9%
Estrone
140 ± 20%
20 ng/L
93.8%
Nonylphenol
1400 ± 20%
200 ng/L
96.1%
Carbamazepine
1400 ± 20%
200 ng/L
99.20%
Phenytoin
200 ± 20%
30 ng/L 99.3% / 98.6.%
Naproxen
140 ± 20%
20 ng/L
93.3%
Bisphenol A
2000 ± 20%
300 ng/L
98.9%
Test Parameters: pH = 7.5 ± 0.5 unless otherwise noted. Flow = 0.5 gpm (1.89 lpm). Pressure = 60 psig (413.7 kPa). Temp. = 68°F to 71.6°F
(20°C to 22°C). Rated service capacity = 200 gallons (757 liters).
The compounds certified under NSF 401 have been deemed as “emerging compounds/incidental contaminants.” Emerging compounds/incidental
contaminants are those compounds that have been detected in drinking water supplies at trace levels. While occurring at only trace levels, these
compounds can affect the public acceptance/perception of drinking water quality.
� For installation, operation, and maintenance instructions please
refer to the Owner's Manual.
� It is important that operational, maintenance, and filter
replacement requirements be carried out for the product to
perform as advertised. Property damage can occur if all instructions
are not followed.
� The disposable cartridge must be changed at least every 6 months.
� Use replacement filter part #EDR1RXD1/EDR1RXD1B. 2015
suggested retail price of $49.99 U.S.A./$49.99 Canada. Prices are
subject to change without notice.
� The filter monitor system measures the amount of water that
passes through the filter and alerts you when it is time to replace
the filter.
� Refer to the “Using the Controls” or “Water Filtration System”
section (in the User Instructions or User Guide) to learn how to
check the water filter status.
� After changing the water filter, flush the water system. See “Water
and Ice Dispensers” or “Water Dispenser” in the User Instructions
or User Guide.
� These contaminants are not necessarily in your water supply. While
testing was performed under standard laboratory conditions, actual
performance may vary.
� For installation, operation and maintenance instructions please
refer Owner's Manual.
Consumer Support 1.800.442.9991
By Whirlpool Corporation
2000 North M63
Benton Harbor, MI 49022
Made in Taiwan.
� The product is for cold water use only.
� The water system must be installed in compliance with state and
local laws and regulations.
� Do not use with water that is microbiologically unsafe or of
unknown quality without adequate disinfection before or after the
system. Systems certified for cyst reduction may be used on
disinfected waters that may contain filterable cysts. EPA Est. No.
082047-TWN-001
� Refer to the “Warranty” section (in the User Instructions or User
Guide) for the Manufacturer’s limited warranty, name and
telephone number.
Application Guidelines/Water Supply Parameters
Water Supply
Water Pressure
Water Temperature
Service Flow Rate
Potable City or Well
30 psi - 120 psi
(207 kPa - 827 kPa)
33° - 100°F (0.6° - 37.8° C)
0.50 GPM (2.27 L/min.) @ 60 psi.
(413.7 kPa)
� Your water filtration system will withstand up to 120 pounds per
square inch (psi) water pressure. If your water supply is higher
than 80 psi, install a pressure reducing valve before installing the
water filtration system.
*Class I particle size: >0.5 to 1 um
†Based on the use of Cryptosporidium parvum oocysts
††Fibers greater than 10 um in length
®
NSF is a registered trademark of NSF International.
10-May-2021 11:18:44 EDT | RELEASED
In some European factories the letter "W" of the part code mentioned herein will be automatically
replaced by the number "4000" (e.g. "W12345678" becomes "400012345678")