Installation Instructions
Table Of Contents
- REFRIGERATOR SAFETY
- MODELS
- INSTALLATION REQUIREMENTS
- Tools and Parts
- Location Requirements
- Electrical Requirements
- Water Supply Requirements
- Tipping Radius
- Product Dimensions
- Door Swing Dimensions
- Overlay Series Door Panel and Cabinetry Clearance
- Custom Overlay Panel Dimensions
- Overlay Series Custom Panels
- Stainless Steel and Overlay Series Both 36" and 42" models have the same cabinet side trim
- INSTALLATION INSTRUCTIONS
- Unpack the Refrigerator
- Reduce Tipping Radius (if required)
- Move the Refrigerator into House
- Install Anti-Tip Boards
- Connect the Water Supply
- Plug in Refrigerator
- Move Refrigerator to Final Location
- Level and Align Refrigerator
- Install Overlay Custom Panels
- Adjust Door(s)
- Install Side Panel
- Install Base Grille
- Complete Installation
- SÉCURITÉ DU RÉFRIGÉRATEUR
- MODÈLES
- EXIGENCES D’INSTALLATION
- Outils et pièces
- Exigences d’emplacement
- Spécifications électriques
- Spécifications de l’alimentation en eau
- Rayon de basculement
- Dimensions du produit
- Dimensions pour l’ouverture des portes
- Dégagement des panneaux de porte de série Overlay et des armoires
- Panneaux personnalisés de série Overlay
- Dimensions des panneaux personnalisés
- Les modèles de série Overlay et en acier inoxydable de 36" et 42" sont dotés de la même garniture latérale de caisse
- INSTRUCTIONS D’INSTALLATION
- Déballage du réfrigérateur
- Réduire le rayon de basculement (le cas échéant)
- Déplacement du réfrigérateur dans le domicile
- Installation de planches antibasculement
- Raccordement à la canalisation d’eau
- Brancher le réfrigérateur
- Déplacement du réfrigérateur à son emplacement définitif
- Réglage de l’aplomb et alignement du réfrigérateur
- Installation des panneaux personnalisés Overlay
- Ajustement des portes
- Installation du panneau latéral
- Installation de la grille de la base
- Terminer l’installation
23
5. Replace the top grille in the cabinet side trims and pull the
panel down slightly to lock it into place.
Adjust Door(s)
Door Alignment
1. Loosen, but do not remove, the four Torx
†
27 at-head
mounting screws. Remove the 1/4" hex-head mounting
screws in the top hinge.
2. Adjust the top hinge of the door to align it.
3. Tighten the Torx
†
27 at-head mounting screws to a torque of
approximately 100 inch-pounds (11.3 Nm).
4. Discard the 1/4" hex-head screws.
Door Height Adjustment (36" [91.4 cm] and
42" [106.7 cm] French Door Models)
Use the following steps to adjust the door height, up or down,
after the refrigerator has been leveled.
NOTE: Adjust the right-hand door to the position of the left-hand
door rst. If it is necessary to adjust the left-hand door, you must
make sure that the hinged center rail located on the left-hand
door does not drag when closing the door.
1. Open the freezer drawer. Remove the locking plate screw
from the bottom side of the refrigerator door hinge using a
1/4" open-end wrench.
2. Remove the locking plate as shown.
3. Turn the bushing located underneath the bottom of the hinge
using a 1/2" open-end wrench. Turning the bushing to the
left will lower the door. Turning the bushing right will raise the
door.
4. After adjusting, check the doors to make sure they are even at
the top and bottom. If the doors are not even, continue to turn
the bushing to adjust the door.
5. Replace the locking plate.
■ Turn the bushing slightly to align the hinge and locking
plate screw holes.
■ Replace and tighten the locking plate screw.
6. Make nal check to make sure the doors are aligned and
even.
B BA
B BA
A. Top grille
B. Cabinet side trims
A
B
A. Torx
†
27 at-head mounting screws
B. 1/4" hex-head mounting screws
BC
A
A. Bushing
B. Locking plate
C. Locking plate screw