Owner's Manual

28
� The quality of your ice will be only as good as the quality of the
water supplied to your ice maker.
� Avoid connecting the ice maker to a softened water supply.
� Water softener chemicals (such as salt) can damage parts of
the ice maker and lead to poor quality ice. If a softened water
supply cannot be avoided, make sure the water softener is
operating properly and is well maintained.
� It is normal for the ice cubes to be attached at the corners.
They will break apart easily.
� For Style 1 ice maker, do not force the wire shutoff arm up or
down.
� Do not store anything on top of the ice maker or in the ice
storage bin/bucket.
Setting Liters and Ounces
C
OZ
Hold [Max Freezer] + [FreshChill] buttons to switch between L and
OZ.
When activated, the corresponding point LED is lit at FULL
brightness. The LED will turn off after 10 seconds if it’s not in the
mode associated to the water amount mode.
The L/OZ only turns on when there is an interaction associated to
water amount (eg, measured fill, calibration).
Measured Fill
Calibrate Measured Fill
Household water pressure may affect the accuracy of the
Measured Fill feature. For optimum performance of your water
dispenser, you must first calibrate Measured Fill.
Start Calibration Mode
1. Press and hold the Measured Fill button for 3 seconds to enter
Calibration Mode. The button will display along with the
0.2 L or 8 oz default settings.
2. Pressing the water pad will dispense water (e.g. into a
measuring cup) until the desired amount is dispensed.
Releasing the water pad will stop water dispensing.
Save and Exiting Calibration
1. If water was dispensed, pressing the Measured Fill button will
save the amount dispensed, a tone will play and the
calibration amount display will blink twice.
2. If no water was dispensed, Pressing the Measured Fill button
will exit Calibration mode without saving the calibration
amount.
NOTE: The amount of water you select will be dispensed. Be sure
that the container is empty and can hold the entire volume. If ice is
in the container, you may need to adjust your selection.
IMPORTANT: Low water pressure may affect the accuracy of this
feature.
1. Press MEASURED FILL to turn the feature on. When the
feature is on, the Measured Fill screen appears on the display.
2. To dispense water, press a sturdy glass against the water
dispenser pad or place the glass below the water dispenser
and press the MEASURED FILL button. Hold the glass close
to the water dispenser spout to ensure that the water
dispenses into the glass.
3. The Measured fill button can be pressed to loop the preset
amounts. Each press advances the preset amount until the
end of the options are reached. Example -
8 oz to 16 oz to 24oz, END (0.2L to 0.5L to 1.0L, END).
NOTE:
� The dispenser will automatically turn off Measured Fill after
1 minute of inactivity. When Measured Fill is turned off, any
changes you have made will be lost and all defaults will be
restored.
� Most coffee cups are 4-6 oz (118-117 ml) and are not the same
size as an 8 oz (237 ml) measuring cup. You may need to
adjust the volume to avoid overfilling coffee cups.
� While dispensing water, the digital display will count down how
much water remains to be dispensed, according to the volume
you selected. The flow of water will automatically stop once the
desired volume has been dispensed.
Water Filtration System
Do not use with water that is microbiologically unsafe or of
unknown quality without adequate disinfection before or after the
system. Systems certified for cyst reduction may be used on
disinfected waters that may contain filterable cysts.
Water Filter Status Indicator
The water filter indicator, located on the control panel, will help
you know when to change the water filter.
Replace status:
� Replace the water filter cartridge when the water filter status
display changes to “Replace.”
Replace Overdue status:
� When the light turns red on the control panel, this tells you that
it is time to change the water filter cartridge.
� It is recommended that you replace the filter when the status
light turns red or water flow to your water dispenser or ice
maker decreases noticeably.
NOTE: If water flow to your water dispenser or ice maker
decreases noticeably, change the filter sooner. The filter should be
replaced at least every 6 months, depending on your water quality
and usage.