Use & Care Guide
4
■ To add rinse aid, open the dispenser lid by gently pushing in
the center of the lid with your thumb while lifting up on the edge.
Pre Wash
OPEN
SLIDE
■ Pour rinse aid into the opening until the indicator level shows
that it is full.
SLIDE
■ Close dispenser by pushing down gently on the lid.
NOTE: For most water conditions, the factory setting will give
good results.
If you are experiencing poor drying performance, try
a higher setting. Turn the arrow adjuster to the next
higher number to increase the amount of rinse aid.
5. Select a cycle
Efcient dishwashers run longer to save water and energy, just as
driving a car slower saves on gas. Typical cycle time is approximately
2
1
/
2
hours but can take less or more time to complete depending
on selections. Push door rmly closed and touch START to repeat
the same cycle and options as in the previous wash cycle, or select
another cycle appropriate for your load. See the Cycle Guide.
6. Select options
You can customize your cycles by selecting the options desired. See
the Cycle Guide. If you change your mind, touch the option keypad
again to turn off the option. Not all options are available for every
cycle. If an invalid option is selected for a given cycle, the lights will
ash. Adding options may increase the cycle time.
7. Start or resume a cycle
NOTE: If needed, run hot water at the sink nearest your dishwasher
until water is hot. Turn off water. With door rmly closed, touch START.
IMPORTANT: If the door is opened for more than a few seconds after
the cycle is started (even during the Delay time), the Start keypad
must be touched again after the door is closed. If Start keypad is not
touched, the Start keypad light with ash, and audible tone will be
heard, and cycle will not resume.
8. Follow the progress of your dishwasher
The display will indicate cycle progress such as Washing, Drying,
Clean, and Sanitized. The cycle has completed when the Clean light
is lit. Refer to the Control chart in the Cycle Guide section for
operation of the Sanitized indicator.
CYCLE GUIDE
IMPORTANT: The sensor in your dishwasher monitors the soil level. Cycle time and/or water usage can vary as the sensor adjusts the cycle for
the best wash performance. If the incoming water is less than the recommended temperature or food soils are heavy, the cycle will automatically
compensate by adding time, heat, and water as needed.
CYCLES ESTIMATED
WASH TIME*
W/O OPTIONS
(HR:MIN)
WATER USAGE
GALLONS
(LITERS)
This cycle senses the load size, soil amount, and toughness of soil, to adjust the cycle
for improved cleaning, using only the amount of water and energy needed.
The ProWash™ cycle is automatically selected if you rst touch the Start keypad.
Includes a heated drying option.*
2:10 to 3:15 3.38 to 7.4
(12.8 to 28.0)
Use for hard-to-clean, heavily soiled pots, pans, casseroles, and regular tableware.
Includes a heated drying option.
2:45 to 3:25 7.4 (28.0)
This cycle is recommended for daily, regular, or typical use to completely wash and dry
a full load of normally soiled dishes. This dishwasher’s government energy certications
were based on the Normal cycle with only the Heat Dry option selected.**
2:00 to 3:10 2.4 to 7.4
(9.09 to 28.0)
For fast results, the Express Wash will clean dishes using slightly more water and energy.
For improved drying, select a heated drying option.
NOTE: Some detergents are not recommended for short wash cycles, please refer
to your detergent packaging for more information. Includes a heated drying option.
0:55 to 1:05 7.87 (29.8)
Use for rinsing dishes, glasses, and silverware that will not be washed right away.
Do not use detergent.
6:45 to 7:25 7.4 (28.0)
*The government energy certications are not based on this cycle. See the Normal cycle description for the government energy certication
cycle. Using the ProWash™ cycle may increase your energy usage.
**No other washing and drying temperature options were selected, and the dishwasher was not subjected to truncated testing. Rinse aid was
not used, and there was no detergent used in the prewash.