Use & Care Guide

5
OPTIONS CAN BE
SELECTED
WITH
WHAT IT DOES ADDED TIME
TO CYCLE
(HR:MIN)
ADDED
WATER
GALLONS
(LITERS)
Raises the main wash temperature to improve
cleaning for loads containing tough, baked-on
food.
ProWash™
Normal
Raises the main
wash temperate
up to 135°F (57°C).
0:00 to 0:30 0 to 3.0
(0 to 11.2)
Dries dishes with heat. This option, with the
use of rinse aid, will provide the best drying
performance. Plastic items are less likely to
deform when loaded in the top rack. Turn the
Heat Dry option off for an air dry.
Available
with any
cycle except
Rinse Only
Activates the heating
element at the end of
a wash cycle to speed
drying times. Heat Dry
defaults to On when
any cycle is selected,
except for Express
Wash and Rinse Only.
Heat Dry:
0:10 to 0:50
Extended
Heat Dry
(includes Heat
Dry time):
0:40 to 1:20
0
Sanitizes dishes and glassware in accordance
with NSF International NSF/ANSI Standard 184
for Residential Dishwashers. Certied residential
dishwashers are not intended for licensed food
establishments. Only sanitizing cycles have
been designed to meet the requirements of the
NSF/ANSI 184 performance standard for soil
removal and for sanitization efcacy. There is
no intention, either directly or indirectly, that all
cycles on a NSF/ANSI 184 certied dishwasher
meet the NSF/ANSI 184 performance standard
for soil removal and for sanitization efcacy.
The Sani Rinse indicator glows at the end of the
cycle if the Sani Rinse option was successfully
completed. If the indicator does not activate, it
is probably due to the cycle being interrupted.
ProWash™
Normal
Increases the main
wash temperature from
105°F (41°C) to 140°F
(60°C) and the nal
rinse from 140°F (60°C)
to 155°F (68°C).
0:00 to 2:20 1.2 to 6.2
(4.8 to 23.3)
Runs the dishwasher at a later time or during
off-peak electrical hours. Select a wash cycle
and options. Touch the Delay keypad. Touch
START/RESUME. Close the door rmly.
NOTE: Anytime the door is opened (such as, to
add a dish), the Start/Resume keypad must be
touched again to resume the delay countdown.
Available
with any
cycle
Delays the start
of a cycle to the
specied time.
0
Use the Control Lock option to avoid unintended use of dishwasher between cycles, or cycle and option changes during
a cycle.
To turn on Control Lock, touch and hold CONTROL LOCK for 3 seconds. Control Lock light will stay on for a short time,
indicating that it is activated. When the Lock indicator is lit, all keypad selections are disabled. If you touch any keypad
selection while your dishwasher is locked, the light ashes three times. The dishwasher door can still be opened/closed
while the controls are locked.
To turn off Control Lock, touch and hold CONTROL LOCK for 3 seconds. Control Lock light turns off.
CONTROL PURPOSE COMMENTS
To start or resume
a wash cycle.
If the door is opened during a cycle or the power is interrupted, the Start/Resume
indicator ashes. Cycle will not resume until the door is closed and Start is touched.
To cancel a wash
cycle after it has
been started
Close the door rmly. Touch and hold CANCEL/DRAIN for 3 seconds. The
dishwasher starts a 2-minute drain (if needed). Let dishwasher drain completely.
To turn the
audible tones
on or off.
Touch and hold HI-TEMP WASH for 3 seconds to turn the audible tones on or
off. Only audible tones for conrming keypad touches can be turned on/off.
Important audible tones, such as indicating a cycle has been interrupted, cannot
be deactivated.
To indicate the
stauts of the
cycle.
The display will indicate cycle progress such as Washing, Drying, Clean, and
Sanitized. The cycle has completed when the Clean light is lit.
If you select the Sani Rinse option, when the cycle is nished, the Sanitized
indicator glows. If the dishwasher did not properly sanitize your dishes, the
Sanitized indicator ashes at the end of the cycle. This can happen if the cycle is
interrupted or if water could not be heated to required temperature. The light goes
off when you open and close door or touch CANCEL.