KDFX 6020 Instructions for use
Before using the dishwasher/connections 4 Electrical connection 5 Precautions and general recommendations 6 How to fill the salt container 7 How to fill the rinse aid dispenser 8 How to fill the detergent dispenser 9 Care and maintenance 10
Before using the dishwasher/connections 1. Removing the packaging and controls: • After unpacking, make sure that the dishwasher is undamaged and that the door closes correctly. If in doubt, contact a qualified technician or your local retailer. • Keep the packaging materials (plastic bags, polystyrene parts, etc.) out of reach of children, as they are potentially dangerous. • This dishwasher has been factory tested to ensure it functions correctly.
Electrical connection 1) For Great Britain only Warning - this appliance must be earthed Fuse replacement If the mains lead of this appliance is fitted with a BS 1363A 13amp fused plug, to change a fuse in this type of plug use an A.S.T.A. approved fuse to BS 1362 type and proceed as follows: 1. Remove the fuse cover (A) and fuse (B). 2. Fit replacement 13A fuse into fuse cover. 3. Refit both into plug.
Precautions and general recommendations • If a fault occurs, switch off the appliance and turn off the water tap. • On completion of the programme switch off the dishwasher and turn off the water tap. • Repairs and technical modifications must be carried out exclusively by a qualified technician. • The water in the dishwasher is not potable. • Do not store inflammable liquids near the dishwasher. • Do not operate the appliance outdoors. • Attention: Danger when door is opened. 6.
How to fill the salt container Settings for dishwashers without water hardness sensor only. In appliances provided with a water hardness sensor, the setting is automatically executed. If the water hardness level falls within category 1 (soft), no salt is required. From a water hardness category of 1–2 (medium), before using the dishwasher, fill the salt container with regeneration salt (to find out the hardness level of water in your area, contact your local Water Board or check the last bill you received).
How to fill the rinse aid dispenser (Not necessary when using a combined action detergent) The rinse aid facilitates drying and prevents the formation of unsightly spots and streaks on crockery. Before using the dishwasher for the first time, fill the rinse aid dispenser. Only use rinse aids recommended for use in domestic dishwashers. 1. Press button A to open the cover (see drawing). 2. Fill the dispenser with rinse aid up to the dotted line (about 100 ml maximum).
How to fill the detergent dispenser Only use detergents recommended for use in domestic dishwashers. Only fill the detergent dispenser prior to starting a wash programme (see the Quick Reference Guide). 1. Press button C to open the cover. 2. How to fill the detergent dispenser. Programmes with pre-rinse: • Powder and/or liquid detergent: pour two thirds of the recommended dosage into the compartment (A); pour one third into the compartment (B).
Care and maintenance Before cleaning or carrying out maintenance, switch off the appliance, disconnect the mains plug and turn off the water tap. Cleaning the outside of the appliance: To clean the outside of the appliance, use a neutral detergent and a damp cloth. Clean the control panel with a damp cloth only. Do not use abrasive detergents. Cleaning the inside of the dishwasher: Regularly wipe the door seal and inside of the door with a damp cloth to remove any food residue. Upper spray arm: 1.
Care and maintenance Cleaning the filters 1. Rotate the microfilter counter-clockwise (in the direction of the arrow “0”) and extract it (E). 2. Remove the wide-mesh filter (F). 3. Remove the fine-mesh filter (G). 4. Clean all filters under running water, paying attention not to bend the fine-mesh filter. Check that no impurities are left inside the dishwasher! 5. To reassemble: insert the wide-mesh filter into the microfilter so it clicks into place. Insert the fine-mesh filter.
Printed in Italy 12/07 5019 796 02005 n GB
