Use and Care Manual

4
■ To add rinse aid, open the dispenser lid by gently pushing in the
center of the lid with your thumb while lifting up on the edge.
Pre Wash
OPEN
SLIDE
■ Pour rinse aid into the opening until the indicator level shows that
it is full.
SLIDE
Full
Ad
d
■ Close dispenser by pushing down gently on the lid.
NOTE: For most water conditions, the factory setting will give
good results.
If you are experiencing poor drying performance, you may
want to try a higher setting. Turn the arrow adjuster to a
higher number to increase the amount of rinse aid.
5. Select a cycle
Efficient dishwashers run longer to save water and energy, just as
driving a car slower saves on gas. Typical cycle time is approximately
2
1
/
2
hours but can take less or more time to complete depending
on selections.
6. Select options
You can customize your cycles by touching the options desired. If you
change your mind, touch the option again to turn off the option. Not
all options are available for every cycle. If an invalid option is selected
for a given cycle, the lights will flash.
7. Follow the progress of your dishwasher
The pocket display will indicate cycle progress such as Washing,
Drying, Clean, and Sanitized. Also, each segment of the progress bar
represents approximately 25 minutes of time remaining. The fan icon
animates during the dry portion of the cycle unless you have selected
a cycle with air dry or the air dry option.
8. Start or resume a cycle
NOTE: If needed, run hot water at the sink nearest your dishwasher
until water is hot. Turn off water.
Push door firmly closed within 4 seconds of touching Start/Resume.
If door is not closed within 4 seconds, the Start/Resume LED will
flash, an audible tone will be heard, and cycle will not start.
IMPORTANT: If anyone opens the door (such as, for adding a dish,
even during the Delay Hours option), Start/Resume keypad must be
touched each time.
CYCLE GUIDE
This information covers several different models. Your dishwasher may not have all of the cycles and options described.
IMPORTANT: The sensor in your dishwasher monitors the soil level. Cycle time and/or water usage can vary as the sensor adjusts the cycle for
the best wash performance. If the incoming water is less than the recommended temperature or food soils are heavy, the cycle will automatically
compensate by adding time, heat, and water as needed.
CYCLES ESTIMATED
WASH TIME
W/O OPTIONS
(HR:MIN)
WATER USAGE
GALLONS
(LITERS)
This cycle senses the load size, soil amount, and toughness of soil, to adjust the
cycle for improved cleaning, using only the amount of water and energy needed.
The ProWash™ cycle is automatically selected if you first touch the Start keypad.*
Includes a heated drying option.
2:30 to 3:20 3.8 to 5.3
(14.3 to 20.2)
Use for hard-to-clean, heavily soiled pots, pans, casseroles, and regular tableware.
Includes a heated drying option.
2:50 to 4:00 4.3 (16.3)
This cycle is recommended for daily, regular, or typical use to completely wash
and dry a full load of normally soiled dishes. This dishwasher’s government
energy certifications were based on the Normal cycle with only the ProDry™
option selected.**
2:20 to 3:30 2.7 to 5.3
(10.4 to 20.2)
Use for lightly soiled items or china and crystal. Includes a heated drying option. 2:10 to 3:30 2.7 to 5.3
(10.4 to 20.2)
When you need fast results, the Express Wash will clean dishes using slightly more
water and energy. Select a heated drying option to improve drying.
0:55 to 1:05 5.2 (19.8)
Use for rinsing dishes, glasses, and silverware that will not be washed right away.
Do not use detergent.
0:15 2.1 (8.1)
*The government energy certifications are not based on this cycle. See the Normal cycle description for the government energy certification
cycle. Using the ProWash™ cycle may increase your energy usage.
**No other washing and drying temperature options were selected, and the dishwasher was not subjected to truncated testing. Rinse aid was not
used, and there was no detergent used in the prewash.