Installation guide

Before youstart,,,
Your safety and the safety of
others are very important.
We have provided many important
safety messages in this manuaJ and
on your appliance. Ak_iays read and
obey all safety messages.
This is the safety alert
symbol.
This symbol alerts you to
potential hazards that can kill or hurt
you and others.
All safety messages will follow the
safety alert symbol and either the
word "DANGER" or "WARNING".
These words mean:
You can be kitled or seriously
injured if you don't immediately
follow instructions.
You can be killed or seriously
injured if you don't follow
instructions.
All safety messages will tell you
what the potential hazard is, tell you
how to reduce the chance of injury,
and tell you what can happen if the
instructions are not followed.
Important: Observe atl governing
codes and ordinances.
WARNING: _f the
information in this manua_
is not followed exactly, a
fire or expRosion may result
causing property damage,
persona_ injury or death.
m Do not store or use
gasoline or other
flammable vapors and
_iquids in the vicinity of
this or any other
appliance.
WHAT TO DO _FYOU
SMELL GAS
o Do not try to _ight any
appliance.
o Do not touch any
eRectrica_ switch.
o Do not use any phone in
your building.
o _mmediatemy call your
gas supplier from a
neighbor's phone. Follow
the gas supp_[er's
instructions.
o _f you cannot reach your
gas supplier, call the fire
department.
_nstaHation and service
must be performed by a
quamified installer, service
agency or the gas
supplier.
Note: The range cooktop is
manufactured for use with Natural gas.
To convert to LR/Propane gas, see the
Gas Conversion instructions provided in
literature package.
Proper gas and electrical supply
¢or_nectionsmust be available. See "Gas
supply requirements," Page 4 and
"Electrical requirements," Page 5.
Important: Obseve at1governing codes
and ordinances.
Do not obstruct flow of combustion
and ventilation air.
Proper installation is your responsibility.
Have a qualified technician install this
range. Make sure you have everything
necessary for correct installation. It is the
installer's responsibility to comply with the
installation clearances specified on the
gas information label. The gas information
label and model/serial rating plate are
located on the surface below the control
panel.
This installation must conform with atl
local codes and ordinances. In the
absence of local codes, installation must
conform with American National
Standard, National Fuel Gas Code ANSi
Z223.1 --latest edition* or CAN/CGA --
B149 -- latest edition* installation codes.
it is the customer's responsibility:
o To contact a qualified electrical installer.
• To assure that electrical installation is
adequate and in conformance with
National Electrical Code, ANSI/NFPA
70 -- latest edition**, or CSA Standard,
C22.1 Canadian Electrical Code, Part 1
-- latest edition*, and all local codes
and ordinances.
Cabinet opening dimensions shown
must be used. Given dimensions are
minimum clearances.
Note: Some cabinet and building
materials are not designed to withstand
the heat produced by the oven for baking
and selfocleaning. Check with your builder
or cabinet supplier to make sure that the
materials used will not discolor,
delaminate or sustain other damage.
The backguard included with the range
must be installed when a standard 24"
(61 cm) deep base cabinet is used and
there is zero clearance between the back
edge of range and combustible rear wall.
For island installations or other
installations with more than 1" (25.4 mm)
clearance to the back wall, use the
optional stainless steel island trim,
included with the range, to cover the
backguard mounting flanges.
All openings in the wall or floor where the
range is to be installed must be sealed.
it is recommended that a range hood be
installed above this range.
Copies of the standards listed may be obtained
from:
• CSA mnternationai
8501 East P_easant Valley Road
Cleveland, Ohio 44131-5515
•* National Fire Protection Association
One Batterymarch Park
Quincy, Massachusetts 02269