Owners Manual
Table Of Contents
- RANGE SAFETY
- Range Safety
- RANGE MAINTENANCE AND CARE
- Self-Cleaning Cycle
- General Cleaning
- INSTALLATION INSTRUCTIONS
- REQUIREMENTS
- Tools and Parts
- Location Requirements
- Electrical Requirements (for Dual Fuel models) - U.S.A. Only
- Electrical Requirements (for Dual Fuel models) - Canada Only
- Electrical Requirements (for Gas models)
- Gas Supply Requirements
- INSTALLATION
- Unpack Range
- Install Anti-Tip Bracket
- Make Gas Connection
- Verify Anti-Tip Bracket Is Installed and Engaged
- Level Range
- Electronic Ignition System
- Complete Installation
- Remove Oven Doors
- Adjust Leveling Legs
- GAS CONVERSIONS
- Propane Gas Conversion
- Natural Gas Conversions
- Moving the Range
- SECURITE DE LA CUISINIERE
- Sécurité de la cuisinière
- ENTRETIEN ET REPARATION DE LA CUISINIERE
- Programme d’autonettoyage (sur certains modèles)
- Nettoyage général
- INSTRUCTIONS D'INSTALLATION
- EXIGENCE
- Tools and Parts
- Exigences d’emplacement
- Spécifications électriques (Pour les modèles à bi-combustible) - Canada seulement
- Spécifications électriques (pour cuisinières à gaz)
- Spécifications de l’alimentation en gaz
- INSTALLATION
- Déballage de la cuisinière
- Installation de la bride antibasculement
- Raccordement au gaz
- Vérifier que la bride antibasculement est bien installée et engagée
- Réglage de l’aplomb de la cuisinière
- Système d’allumage électronique
- Achever l’installation
- Enlever la/les portes du four
- Réglage des pieds de nivellement
- CONVERSIONS POUR CHANGEMENT DE GAZ
- Propane Gas Conversion
- Natural Gas Conversion
- Déplacement de la cuisinière
20
6. Position the broil burner against the roof of the oven cavity
and attach with screw.
A. Broil burner orifice hood
B. Broil burner
To Convert Surface Burners (Natural gas to
Propane)
1. Remove burner cap.
2. Remove the burner base.
A. Burner cap
B. Burner base
C. Alignment pins
D. Igniter electrode
E. Gas tube opening
3. Apply masking tape to the end of a 9/32" (7 mm) nut driver to
help hold the gas orifice spud in the nut driver while changing
it. Press nut driver down onto the gas orifice spud and remove
by turning it counterclockwise and lifting out. Set gas orifice
spud aside.
A. Igniter electrode
B. Orifice spud
C. Orifice spud holder
D. Screws
4. Remove the orifice spuds shipped in the literature package in
the oven. Gas orifice spuds are stamped with a number and
have a groove in the hex area. Replace the Natural gas orifice
spud with the correct Propane gas orifice spud.
A. Propane groove
Refer to the following chart for correct Propane gas orifice
spud ratings and to spud holder card for proper placement.
Propane Gas Orifice Spud Chart for Surface Burner
Burner Rating Number
4,000 BTU
7,000 BTU
9,100 BTU
14,000 BTU
064AM
080AM
096AM
108AM
NOTE: Refer to the Model Number and Serial Number Plate
located on the oven frame behind the top right side of the oven
door for proper sizing of spuds for each burner location.
5. Place Natural gas orifice spuds in the orifice spud bag.
IMPORTANT: Keep the Natural gas orifice spuds in case of
reinstallation with Natural gas.
6. Replace the burner base.
7. Replace burner cap.
8. Repeat steps 1-7 for the remaining burners.
9. Place Natural gas orifice spuds in plastic parts bag for future
use and keep with literature package.
10. Replace burner grates.
11. Complete installation. See the “Make Gas Connection” and
“Electronic Ignition System” sections.
Checking for proper cooktop burner flame is very important.
The small inner cone should have a very distinct blue flame 1/4" to
1/2" (0.64 to 1.3 cm) long. The outer cone is not as distinct as the
inner cone. Propane gas flames have a slightly yellow tip.
IMPORTANT: You may have to adjust the LO setting for each
cooktop burner. See “Adjust Flame Height” in the “Electronic
Ignition System” section.