Installation guide

Before youstart+++
Your safety and the safety of others are
very important.
We have provided many important
safety messages in this manua[ and on
your appiiance. Aiways read and obey
all[ safety messages.
This is the safety aiert symbol
This symbo[ aierts you to
potenfia[ hazards that can MH[
or hurt you and others.
AH[ safety messages will[ foiiow the
safety aiert symbo[ and either the word
"DANGER" or "WARNHNG".These
words mean:
You can be killed or sedousJy injured
if you don't immediateJy foJJow
instructions.
You can be k+Hed or seriously injured if
you don't follow instructions.
All safety messages will tell you what
the potential hazard is, tell you how to
reduce the chance of injury, and tell
you what can happen if the
instructions are not followed.
iMPORTANT: Observe all governing
codes and ordinances,
WARNING: Jf the
information +nthis manua_
+s not followed exactmy, a
fire or expRos+on may result
causing property damage,
persona_ injury or death.
m Do not store or use
gasom+ne or other
flammabme vapors and
[iqu+ds +n the v+c+nity of
th+s or any other
appliance.
WHAT TO DO +FYOU
SMELL GAS
o Do not try to light any
app[+ance.
o Do not touch any
emectr+ca[ sw+tch.
o Do not use any phone +n
your bu+[d+ng.
o +mmed+atemy caromyour
gas supplier from a
ne+ghbor's phone. Follow
the gas suppHer's
+nstruct+ons.
o +fyou cannot reach your
gas supplier, call the fire
department.
+nstaHat+on and service
must be performed by a
qualified +nstaHer, service
agency or the gas
supplier.
NOTE:This cooktop is manufactured for
use with Natural gas×+.To convert to
hR/Propane gas, see instructions in the
Gas Conversion Kit provided in literature
package_
Proper gas supply connection must be
available. See "Gas supply
requirements;' Page 4_
Proper installation is your responsibility.
Have a qualified technician install this
cooktop.
Make sure you have everything
necessary for correct installation. It is the
responsibility of the installer to comply
with the installation clearances specified
on the model/serial rating plate.The
model/serial rating plate can be found on
the underside of the cooktop burner box.
Check location where cooktop will be
instalbd.The location should be away
from strong draft areas, such as
windows, doors and strong heating vents
or fans.
Do not obstruct flow of combustion and
ventilation air.
All openings in the wall or floor where
the cooktop is to be installed must be
sealed.
When installing a cooktop under existing
cabinets and the installation does not
meet the minimum cabinet clearances,
install a range hood above the cooktop
to avoid burn hazards.
Electrical ground is required. See
"Electrical Requirements;' Pages 4-5.
It is the customer's responsibility:
+ To contact a qualified electrical installer.
+ To assure that electrical installation is
adequate and in conformance with
National Electrical Code, ANSl/NEPA
70 -- latest edition xx, or Canadian
Electrical Code, C22.1 -1982 antiC22.2
No. 01982 (or latest edition) +__+ and aii
local codes and ordinances.
Copies of the standards listed may be
obtained from:
_National Fire Protection Association
One Batterymarch Park
Quincy, Massachusetts 02269
_*_CSA International
8501 East Pleasant Valley Rd.
Cleveland, OH 44131-5575
+Exception: Model KGCR055 is
manufactured for use with LP gas _,
Assemble the required tools and parts
before starting installation. Read and
follow the instructions provided with any
tools listed here.
+ ruler or tape measure
* flat-blade screwdriver
* pencil
* pliers